Installation Guide

ManualsBrandsMetra ManualsAudioMetra Dash Kit Nissan Sentra 2020-Up

Metra. The World’s Best Kits.



INSTALLATION INSTRUCTIONS

95-7 638

Attention! Let the vehicle sit with the key

out of the ignition for a few minutes before

removing the factory radio. When testing the

aftermarket equipment, ensure that all factory

equipment is connected before cycling the

key to ignition.

KIT FEATURES

• ISO DDIN radio provision †

• Pioneer modular DDIN radio provision †

• Painted with a gloss black face, silver trim, and a textured housing.

KIT COMPONENTS

• A) Radio housing (front) • B) Radio housing (rear) • C) Radio trim panel • D) Radio brackets • E) Pioneer adapter brackets

• F) #4 x 3/8” Phillips screws (4) • G) #6 x 3/8” Phillips screws (4) • H) Panel clips (3)

TOOLS REQUIRED

• Panel removal tool • Phillips screwdriver

• 10mm socket wrench

TABLE OF CONTENTS

Dash Disassembly ..................................................2

Kit Assembly

– ISO DDIN radio provision ................................3-4

– Pioneer modular DDIN radio provision.........5-6

WIRING & ANTENNA CONNECTIONS

(sold separately)

Wiring Harness: 70-7552

Antenna Adapter: 40-NI12

A B C

F G

D E

Nissan Sentra 2020-Up

Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle

speciﬁc applications

† This kit can only be used with an ISO DDIN radio with an “L” shaped chassis design, with the radio

chassis at the bottom of the screen. As of this writing, only the Alpine INE-W967HD (discontinued,

replaced by INE-W977HD), iLX-107, and iLX-207 have this design. Also, The Pioneer modular radios,

DMH-C2550NEX and DMH-C2500NEX, can also be used with the included adapter brackets.

Summary of content (8 pages)

PAGE 1
95-7638 I N S TA L L AT I O N I N S T R U C T I O N S Nissan Sentra 2020-Up Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle specific applications KIT FEATURES • ISO DDIN radio provision † • Pioneer modular DDIN radio provision † • Painted with a gloss black face, silver trim, and a textured housing. † This kit can only be used with an ISO DDIN radio with an “L” shaped chassis design, with the radio chassis at the bottom of the screen.
PAGE 2
DASH DISASSEMBLY 1. Unclip and remove the trim panel behind the radio. There are (4) clips securing this panel to the dash. Use caution as the front of the trim panel can easily be damaged. (Figure A) Note: Dash vents may vary depending on Nissan model. 2. Remove (4) 10mm screws securing the radio. Take note that the lower radio brackets are angled inward, hiding the bottom (2) screws from being easily seen. Slide the radio out, then unplug and remove the radio.
PAGE 3
KIT ASSEMBLY ISO DDIN radio provision 1. Attach (3) panel clips provided onto the radio housing (front). (Figure A) 2. Snap the radio housing (front) to the radio housing (rear), then secure using (4) #4 x 3/8” Phillips screws provided (Figure B) 3. Secure the radio brackets to the radio housing using (4) #6 x 3/8” Phillips screws provided. (Figure C) (Figure A) (Figure B) (Figure C) Continued on the next page REV.
PAGE 4
KIT ASSEMBLY (CONT.) 4. Slide the radio into the radio housing assembly through the front, then secure it to the assembly using screws supplied with the radio. (Figure D) 5. Clip the radio trim panel onto the radio housing assembly. (Figure E) 6. Locate the factory wiring harness and antenna connector in the dash and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra and/or Axxess. Test the radio for proper operation. 7.
PAGE 5
KIT ASSEMBLY Pioneer Modular DDIN radio provision 3. Secure the radio brackets to the radio housing using (4) #6 x 3/8” Phillips screws provided. (Figure C) Note: For steps 4 and 5, reference the installation manual provided with the radio for which hardware to use. The display screen and radio chassis use two different types of screws. 4. Secure the radio display to the Pioneer adapter brackets using (6) screws supplied with the radio. (Figure D) Continued on the next page 1.
PAGE 6
KIT ASSEMBLY (CONT.) 8. Locate the factory wiring harness and antenna connector in the dash and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra and/or Axxess. Test the radio for proper operation. 5. Secure the display and bracket assembly to the radio chassis using (4) screws supplied with the radio. (Figure E) 6.
PAGE 7
REV.
PAGE 8
95-7638 I N S TA L L AT I O N I N S T R U C T I O N S If you are having difficulties with the installation of this product, contact our Tech Support line either by phone at 386-257-1187, or email at techsupport@metra-autosound.com. Before doing so, look over the instruction booklet a second time and ensure that the installation was performed exactly as the instruction booklet is stated. Have the vehicle apart and ready to perform troubleshooting steps before contacting Metra/Axxess Tech Support.