Installation Guide

ManualsBrandsMetra ManualsAudioMetra Audi A4 And A5 2009-2016 Car Dash Installation Kit

Metra. The World’s Best Kits.



INSTALLATION INSTRUCTIONS

95-9110B

Attention! Let the vehicle sit with the key

out of the ignition for a few minutes before

removing the factory radio. When testing the

aftermarket equipment, ensure that all factory

equipment is connected before cycling the

key to ignition.

• ISO DDIN radio provision

• Includes all necessary data interfaces, wiring harnesses, and antenna

adapter, for a complete installation

• Info Adapter kit, retains information on display

• Painted matte black

KIT FEATURES

KIT COMPONENTS

• A) Radio trim panel • B) Radio brackets • C) Radio screws (8) • D) Panel clips (2) • E) AXSWC/camera retention wiring harness (not shown)

• F) Axxess interface and wiring harness (not shown) •G) Antenna adapter (not shown)

TOOLS REQUIRED

• Panel removal tool • Phillips screwdriver

• 8mm Socket wrench • Pick tool

TABLE OF CONTENTS

Dash Disassembly ..................................................2

Kit Assembly ..........................................................3

Axxess Interface Installation .............................4-8

Final Assembly .......................................................9

User Guide .........................................................9-12

WIRING & ANTENNA CONNECTIONS

Wiring Harness: Included with kit

Antenna Adapter:

Included with kit

Steering Wheel Control Interface: Included with kit

Audi A4 (8K) A5 (8TF/8/F7/8TA) 2009-2016

A B C D

Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle

speciﬁc applications

Audi with MMI

Audi w/o MMI

(w/o MMI / w/o factory ampliﬁer / dual zone only / excluding ’09 convertible)

Summary of content (16 pages)

PAGE 1
95-9110B I N S TA L L AT I O N I N S T R U C T I O N S Audi A4 (8K) A5 (8TF/8/F7/8TA) 2009-2016 Audi with MMI (w/o MMI / w/o factory amplifier / dual zone only / excluding ’09 convertible) Visit MetraOnline.
PAGE 2
DASH DISASSEMBLY 1. Unclip, unplug, and remove the bezel surrounding the OE screen. (Figure A) Disconnect the Hazard and Airbag connector from the trim panel. 3. To remove the HVAC controls place the hook tool in the hole on the bottom left of the VAC controls and pull gently. (Figure D) 2. The vent assembly has four spring clip in each corner of the A/C vents. Insert metal hook tool through the A/C vent and press the metal clip inside releasing each corner.
PAGE 3
KIT ASSEMBLY 1. Secure the radio brackets to the radio using either the screws supplied with the radio, or the radio screws provided. (Figure A) (Figure A) REV.
PAGE 4
AXXESS INTERFACE INSTALLATION INTERFACE FEATURES • Provides accessory power • Retains audio/phone† controls on the steering wheel • Retains vehicle personalization and setting menus • Provides NAV outputs (parking brake, reverse, speed sense) • Provides input for aftermarket reverse camera • Retains balance • Micro-B USB updatable † Radio dependent INTERFACE COMPONENTS • 9110B interface • 9110B harness • AXSWC interface • SWC/camera retention harness • Female 3.
PAGE 5
CONNECTIONS From the 9110B harness to the aftermarket radio: The following (3) wires are only for multimedia/navigation radios that require these wires. • Connect the Black wire to the ground wire. • Connect the Blue/Pink wire to the speed sense wire. • Connect the Yellow wire to the battery wire. • Connect the Green/Purple wire to the reverse wire. • Connect the Red wire to the accessory wire. • Connect the Light Green wire to the parking brake wire.
PAGE 6
CONNECTIONS From the SWC/camera retention harness to the aftermarket radio: This harness is to be used if the vehicle is equipped with steering wheel controls. • Connect the Red wire to the accessory wire. • For the radios listed below: Connect the female 3.5mm connector with stripped leads, to the male 3.5mm SWC jack from the AXSWC harness. Any remaining wires tape off and disregard: • Eclipse: Connect the steering wheel control wire, normally Brown, to the Brown/White wire from the connector.
PAGE 7
INSTALLATION PROGRAMMING With the key in the off position: 1. Press and hold the Volume Up button on the steering wheel. 1. Connect the 9110B harness to the interface. 2. Turn the ignition on, the L.E.D. in the AXSWC interface will start flashing rapidly, which means the AXSWC interface is looking for the vehicle and the radio. 2. Connect the SWC/camera retention harness to the AXSWC interface, and then to the 9110B interface. 3. Connect the video cables according to the type of camera.
PAGE 8
PROGRAMMING (CONT.) L.E.D. Feedback The (18) Red L.E.D. flashes represent the brand of radio the AXSWC interface believes it is connected to. Each flash count represents a different radio Manufacturer. For example, if you are installing a JVC radio, the AXSWC interface will flash Red (5) times, then stop. Following is a legend that explains which radio Manufacturer corresponds to the flash count provided. L.E.D.
PAGE 9
FINAL ASSEMBLY 1. Using the 8mm bolts secure the radio assembly to the dash. USER GUIDE SWC Controls and menu operation 2. Reconnect HVAC harnessing and snap back into dash. 2 3. Reconnect and attach the a/c vent panel. 4. Snap the screen trim panel back into the dash, this will complete your installation. 4 1 3 In Normal Mode In Infodapter Menu 1. Track + (Scroll Up) Track - (Scroll Down) Source (Short Press) Enter Infodapter Menu (Long Press) 1.
PAGE 10
INFOADAPTER MENU Configuration Menu Press and hold Button 1 or Button 2 to enter the Infodapter Configuration menu and navigate through the various options and settings. 10 Drive Select Settings Individual / Comfort / Auto / Dynamic / Off Road / Efficiency 386.257.1187 | MetraOnline.
PAGE 11
INFOADAPTER MENU Vehicle Settings (CONT.) Unit Settings • Distance • Speed • Temperature • Tire Pressure Units The Infodapter interface currently retains the following vehicle settings*: Time/Date • Hours • Minutes • Years • Month • Day • Set Time Format • Set Date Format *Note: Although care has been taken to ensure the accuracy of this menu structure at the time of printing this document, sudden changes in software by the manufacturer or incompatibilities with the interface cannot be accounted for.
PAGE 12
INFOADAPTER MENU (CONT.
PAGE 13
REV.
PAGE 14
386.257.1187 | MetraOnline.
PAGE 15
REV.
PAGE 16
95-9110B I N S TA L L AT I O N I N S T R U C T I O N S Having difficulties? We’re here to help. Contact our Tech Support line at: 386-257-1187 Or via email at: techsupport@metra-autosound.com Tech Support Hours (Eastern Standard Time) Monday - Friday: 9:00 AM - 7:00 PM Saturday: 10:00 AM - 7:00 PM Sunday: 10:00 AM - 4:00 PM ® KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.