Installation Instructions

ManualsBrandsMetra ManualsAudioMetra Porsche Cayenne (958) 2011-2016 Dash Kit

The World’s Best Kits.

INSTALLATION INSTRUCTIONS

95-9609B

Attention!

Let the vehicle sit with the key

out of the ignition for a few minutes before

removing the factory radio. When testing the

aftermarket equipment, ensure that all factory

equipment is connected before cycling the

key to ignition.

KIT FEATURES

• ISO DDIN radio provision

• Includes an Axxess interface for retaining CAN data information

• Includes an Axxess interface for retaining steering wheel control

functionality

• Painted matte black

KIT COMPONENTS

• A) Radio bezel • B) Radio brackets • C) ISO DDIN trim ring •

D) Phillips

machine-thread

screws (4)

• E) Phillips

standard-thread

screws (4)

• F) Axxess interface (not shown) • G) Axxess SWC interface (not shown)

TOOLS REQUIRED

• Panel removal tool • Phillips screwdriver

• Thin ﬂat-blade screwdriver • T-27 Torx screwdriver

TABLE OF CONTENTS

Dash Disassembly ..................................................2

Kit Assembly ..........................................................3

Axxess Interface Installation ..............................4-6

Final Assembly .......................................................7

A B C

Porsche Cayenne

(958)*

2011-2016

* Without amp

Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle

speciﬁc applications

WIRING & ANTENNA CONNETIONS

Wiring Harness: Included with kit

Antenna Adapter: Included with kit

Steering Wheel Control Interface: Included with kit

Summary of content (8 pages)

PAGE 1
95-9609B I N S TA L L AT I O N I N S T R U C T I O N S Porsche Cayenne (958)* 2011-2016 * Without amp Visit MetraOnline.
PAGE 2
DASH DISASSEMBLY 1. Unclip, unplug and remove the center a/c vents. There are (6) clips † on each vent that secure it to the dash. To release the clips, insert a thin flat-blade screwdriver into the vents, then push on the clips outward. Release the outermost clips first. (Figure A) † The clips are located: (1) top, (1) bottom, (2) each side. (Figure B) 2. Remove (4) T-27 Torx screws securing the radio. Slide the radio out, then unplug and remove.
PAGE 3
KIT ASSEMBLY 1. Secure the radio brackets to the radio using screws supplied with the radio. (Figure A) Note: There are (4) Phillips machinethread screws provided in case the radio doesn’t come with screws. 2. Place the radio bezel over the radio assembly, then secure using (4) Phillips standard-thread screws provided. (Figure B) Note: An ISO DDIN trim plate is provided for smaller nose radios which produce a gap around the radio. (Figure A) (Figure B) Continue to Axxess Interface Installation REV.
PAGE 4
AXXESS INTERFACE INSTALLATION 4 INTERFACE FEATURES • Provides accessory power • Provides illumination, parking, brake, reverse, and speed sense outputs • Retains audio controls on the steering wheel • Retains parking sensor audio • Retains the factory backup camera • Retains the factory AUX-IN jack and USB port • Designed for non-amplified models • Retains balance and fade • Micro-B USB updatable TABLE OF CONTENTS Connections................................................................................
PAGE 5
CONNECTIONS • Light Green wire to the parking brake wire. † From the 9609 harness to the aftermarket radio, connect the: • Black wire to the ground wire. • Yellow RCA jack to the backup camera input. † • Yellow wire to the battery wire • Red & White RCA jacks labeled “AUX Left” and “AUX Right” to the audio AUX-IN jacks. † • Red wire to the accessory wire. • Disregard the Red & White RCA jacks labeled “FRONT LEFT” and “FRONT RIGHT”.
PAGE 6
INSTALLATION With the ignition switch in the off position, connect the: 1. SWC harness to the SWC interface, then to the 9609 interface. 2. 9609 harness to the 9609 interface, then to the wiring harness in the vehicle. 3. USB harness to the radio, then to the wiring harness in the vehicle. 4. Locate the factory antenna connector in the dash and complete all necessary connections to the radio. Use the antenna adapter provided to adapt the factory antenna to the aftermarket radio. PROGRAMMING 1.
PAGE 7
FINAL ASSEMBLY 1. Slide the radio assembly into the dash, then secure using the factory screws. 2. Reassemble the dash in reverse order of disassembly to complete the installation. REV.
PAGE 8
95-9609B I N S TA L L AT I O N I N S T R U C T I O N S If you are having difficulties with the installation of this product, contact our Tech Support line either by phone at 386-257-1187, or email at techsupport@metra-autosound.com. Before doing so, look over the instruction booklet a second time and ensure that the installation was performed exactly as the instruction booklet is stated. Have the vehicle apart and ready to perform troubleshooting steps before contacting Metra/Axxess Tech Support.