Installation Guide

ManualsBrandsMetra ManualsAudioPorsche Macan (95B) 2015-2016 Dash Kit (With OE Amp & Parking Sensors)

Metra. The World’s Best Kits.



INSTALLATION INSTRUCTIONS

95-9616B

Attention! Let the vehicle sit with the key

out of the ignition for a few minutes before

removing the factory radio. When testing the

aftermarket equipment, ensure that all factory

equipment is connected before cycling the

key to ignition.

KIT FEATURES

• ISO DDIN radio provision

• Includes an Axxess interface for retaining CAN data information

• Includes an Axxess interface for retaining the ﬁber-optic MOST-25

ampliﬁer

• Includes an Axxess interface for retaining steering wheel control functionality

• Painted matte black

TOOLS REQUIRED

• 3mm Allen screwdriver • Long hook tool

• Panel removal tool • T-27 Torx screwdriver

TABLE OF CONTENTS

Dash Disassembly ..................................................2

Kit Assembly ..........................................................3

Axxess Interface Installation ............................4-10

Final Assembly .......................................................7

WIRING & ANTENNA CONNECTIONS

Wiring Harness: Included with kit

Antenna Adapter: Included with kit

Steering Wheel Control Interface:

Included with kit

Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle

speciﬁc applications

Porsche Macan (95B)† 2015-2016

For Ampliﬁed vehicles, with OEM parking sensors and graphics on vehicle screen

† With ﬁber optic MOST-25

amp

KIT COMPONENTS

• A) Radio trim panel • B) Radio brackets • C) (4) #8 3/8” Phillips screws

A B C

Summary of content (12 pages)

PAGE 1
95-9616B I N S TA L L AT I O N I N S T R U C T I O N S Porsche Macan (95B)† 2015-2016 For Amplified vehicles, with OEM parking sensors and graphics on vehicle screen Visit MetraOnline.
PAGE 2
DASH DISASSEMBLY 4. Carefully remove the hinged door covering the DVD drive. (Figure D) 1. Unclip and remove the a/c vent panel to the left of the radio. (Figure A) 5. With the parking brake on, put the gear shifter in reverse to allow the radio to be removed in the following step. Tip! A long-hook too can be inserted into the vent to grab it from the back. 2. Unclip and remove the passenger-side dashboard trim panel. (Figure B) 6. Unclip and slide the radio assembly out, then unplug and remove. 3.
PAGE 3
KIT ASSEMBLY 1. Attach the radio brackets to the radio trim panel using (4) #(8) x 3/8” Phillips screws supplied. (Figure A) 2. Slide the radio into the completed assembly, and then secure it to the assembly using screws supplied with the radio. Continue to Axxess Interface Installation (Figure A) (Figure B) REV.
PAGE 4
AXXESS INTERFACE INSTALLATION KIT ASSEMBLY INTERFACE FEATURES • Provides accessory power • Provides illumination, parking brake, reverse, and speed sense outputs • Retains audio controls on the steering wheel • Retains parking sensor audio • Retains parking sensor graphics † • Retains the factory backup camera • Retains the factory AUX-IN jack and USB port • Designed for models with a fiber-optic MOST-25® amplifier• Retains balance • Retains balance • Micro-B USB updatable † Through the backup camera input
PAGE 5
CONNECTIONS From the 9616 harness to the aftermarket radio, connect the: From the SWC harness to the aftermarket radio: • Black wire to the ground wire. • Parrot: Connect the AX-SWC-PARROT (sold separately) to the 3.5mm jack, then to the radio. • Yellow wire to the battery wire • For the radios listed below: Connect the 3.5mm adapter to the 3.5mm jack. • Red wire to the accessory wire. Note: There will also be a Red wire on the SWC harness to connect as well.
PAGE 6
INSTALLATION PROGRAMMING With the ignition switch in the off position, connect the: 1. Open the driver’s door and keep open during the programming process. 1. SWC harness to the SWC interface, then to the 9616 interface. 2. Press and hold the Volume Up button on the steering wheel. For models with a scroll wheel, scroll up quickly. 2. 9616 harness to the MOST-25® interface. a. Remove the dust cover from fiber-optic port in the MOST-25® interface. 3. Cycle the ignition switch on. b.
PAGE 7
FINAL ASSEMBLY 1. Secure the radio assembly into the dash using the factory hardware and reassemble the dash in reverse order of disassembly. REV.
PAGE 8
USER GUIDE Steering Wheel Control Functionlity *Programmable button In Normal Mode The diamond button on the steering wheel can be programmed to perform a specific radio function within the Infodapter menus on both a long and short press. 1. Volume Up (Scroll Up) Volume Down (Scroll Down) Mute (Short Press) Enter Infodapter Menu (Long Press) 2. *Programmable Function (Short Press) Programmable Function (Long Press) 3. 4. 5. 6. 7.
PAGE 9
USER GUIDE (CONT.
PAGE 10
USER GUIDE (CONT.) OEM Parking sensor graphics The Infodapter interface will automatically generate a replication of the OEM front/ rear parking sensor graphics based on the vehicle’s data. These graphics have been designed to exactly replicate Porsche’s original as closely as possible to retain the OEM feel of the system.
PAGE 11
REV.
PAGE 12
95-9616B I N S TA L L AT I O N I N S T R U C T I O N S Having difficulties? We’re here to help. Contact our Tech Support line at: 386-257-1187 Or via email at: techsupport@metra-autosound.com Tech Support Hours (Eastern Standard Time) Monday - Friday: 9:00 AM - 7:00 PM Saturday: 10:00 AM - 7:00 PM Sunday: 10:00 AM - 4:00 PM ® KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.