99-2001 APPLICATIONS GM MULTI MULTI KIT GM KIT 99-2001 AW-200GM KIT FEATURES • DIN Head Unit w/ Equalizer Provision KIT COMPONENTS A) Radio Housing • B) Spacer • C) Equalizer Dummy Plate • D) Shaft Masks A C B D TOOLS REQUIRED: Phillips Screwdriver 1-800-221-0932 • Utility Knife • Socket Wrench www.metraonline.com © COPYRIGHT 2004-2007 METRA ELECTRONICS CORPORATION INST-2001 - Rev.
VEHICLE APPLICATION CONTENTS BUICK Century Le Sabre Park Avenue Rainier Regal Rendezvous Riviera Roadmaster Skylark 3 4,5 4,5 23 3 6 7 8 9 2003-2006 Sonoma Yukon/Denali/XL HUMMER H2 ISUZU Ascender I Series Truck OLDSMOBILE Achieva 2002-2004 2003-2006 11 10 2003-2007 21,22 2003-2005 2006-2008 28 35 1996-1998 24 Alero 1999-2004 25 10 Aurora 1995-2003 26 Bravada 1998-01 11 2003-2006 10 Bravada 2002-04 23 Blazer 2002-2005 11 Cutlass 1997-1999 27 Cavalier 2000-2005 12 Colorado
99-2001 BUICK • Century 1997-04 / Regal 1997 - 04 Disconnect the negative battery terminal to prevent an accidental short circuit. 4. Unclip top edge of panel below steering column and let hang. 5. Remove (1) 9/32" screw from right side of instrument cluster and radio trim panel and remove entire panel from right to left. 6. Remove (3) 9/32" screws to remove radio. Continue to kit assembly. DASH DISASSEMBLY 1. Open both doors and remove end caps from both ends of dashboard. 2.
99-2001 BUICK • LeSabre 1995-99 / Park Avenue 1995-99 Disconnect the negative battery terminal to prevent an accidental short circuit. DASH DISASSEMBLY 1. Unsnap the climate control trim panel (from door to door) and remove (5) 9/32” 4 screws exposed. 2. Pop out the a/c vents and remove (1) Phillips screw exposed in each vent cavity. 3. Unclip the radio trim bezel and remove. 4. Remove the screws securing the factory head unit and disconnect the wiring. Continue to kit assembly.
99-2001 BUICK • LeSabre 2000-04 / Park Avenue 2000-04 Disconnect the negative battery terminal to prevent an accidental short circuit. 2. Remove (2) Phillips screws from underneath steering column cover. 3. Unsnap and remove steering column cover. 4. Unsnap and remove instrument panel. 5. Remove (2) 9/32" screws and remove radio. Continue to kit assembly. DASH DISASSEMBLY 1. Open drivers door and unsnap and remove dash end cap.
99-2001 BUICK • Rendezvous 2002-04 Disconnect the negative battery terminal to prevent an accidental short circuit. DASH DISASSEMBLY 1. Open center console and remove 2 screws at front of console opening. 6 2. Remove liners from cup holders and storage pocket next to cup holders, then remove screws. Unsnap and remove panel. 3. Remove (2) screws from bottom of radio/climate control bezel, unclip and remove. 4. Remove (3) 9/32" hex head screws to remove radio. Continue to kit assembly.
99-2001 BUICK • Riviera 1996-99 Disconnect the negative battery terminal to prevent an accidental short circuit. DASH DISASSEMBLY 1. Unsnap left side panel exposing (1) Phillips screw to remove. 2. Remove (1) Phillips screw and unsnap right side panel to expose (1) Phillips screw beneath panel and remove. 3. Unsnap underside of overhanging dash to unsnap (6) plastic rivets and remove panel. 4. Remove (5) hex head screws now exposed under overhang. 5.
99-2001 BUICK • Roadmaster 1995-96 Disconnect the negative battery terminal to prevent an accidental short circuit. DASH DISASSEMBLY 1. Unclip dash panel sides and remove. 8 2. Unclip panel below steering column and remove. 3. Unclip panel next to glove box on passenger side and remove. 4. Remove (2) 7mm screws above instrument cluster. 5. Set parking brake, turn car on, and move shifter to the lowest gear. Tilt steering wheel down then unsnap entire instrument cluster/radio panel and remove. 6.
9-2001 BUICK • Skylark 1996-98 Disconnect the negative battery terminal to prevent an accidental short circuit. 2. Under glove box and drivers knee bolster, remove (2) plastic panels by turning (2) 1/4 turn fasteners per side. 3. Remove (4) 9/32" screws revealed. (2 per side). 4. Unsnap panel from driver's side to passenger's side. 5. Remove (3) 9/32" screws to remove radio. Continue to kit assembly. DASH DISASSEMBLY 1. Remove (6) 9/32" screws inside glove box.
DASH DISASSEMBLY 99-2001 10 CADILLAC • Escalade 2003-04 CHEVROLET • Avalanche 2003-04 Silverado 2003-04 / Suburban 2003-04 Tahoe 2003-04 GMC • Sierra 2003-04 Yukon / Denali / XL 2003-04 Disconnect the negative battery terminal to prevent an accidental short circuit. 1. Unsnap and remove dash bezel. 2. Remove (3) 9/32" screws and remove radio. Continue to kit assembly.
99-2001 CHEVROLET • Blazer 2002-04 / S-10 2002-04 GMC • Sonoma 2000-04 OLDSMOBILE • Bravada 1998-01 1. Remove (2) 9/32" hex-head screws from the knee bolster. 2. Pull down on the bolster and remove 9/32" screws exposed on the base of the dash trim bezel. 3. Remove (1) Phillips screw above the instrument cluster. 4. Unclip the dash trim bezel and remove. 5. Unclip the dash trim bezel and remove. Continue to kit assembly.
99-2001 CHEVROLET • Cavalier 2000-04 DASH DISASSEMBLY Disconnect the negative battery terminal to prevent an accidental short circuit. 12 1. Open driver door and remove fuse panel on the end of dash. 2. Open passenger door and remove panel on end of dash. 3. Remove (1) Phillips screw from each side exposed. 4. Remove (3) screws from top of glove box liner. 5. Remove (2) screws from the top-left corner of the glove box cavity. 6. Remove (1) Phillips screw from the defroster duct. 7.
99-2001 CHEVROLET • Express Van 2001-02 / GMC • Savanna 2001-02 Disconnect the negative battery terminal to prevent an accidental short circuit. 2. Unsnap radio/climate/instrument panel. 3. Move shift lever to first gear position. 4. Rotate panel counterclockwise to lift over steering column and remove. 5. Remove (3) 9/32" hex head screws to remove radio. Continue to kit assembly. DASH DISASSEMBLY 1. Unsnap and remove small trim panel below steering column.
99-2001 CHEVROLET • Express Van 2003-04 / GMC • Savanna 2003-04 DASH DISASSEMBLY Disconnect the negative battery terminal to prevent an accidental short circuit. 14 1. Remove (2) 10mm bolts from below knee bolster under steering column and remove panel. 2. Remove (2) 10mm bolts from panel below passenger dash air bag and remove panel. 3. Remove (2) 10mm nuts from inside center pocket between power outlets. 4. Unsnap and remove radio and instrument cluster panel.
99-2001 CHEVROLET • Impala 2000-04 Disconnect the negative battery terminal to prevent an accidental short circuit. 2. Remove (2) Phillips screws under the instrument cluster. 3. Unclip the trim panel above the pedals. (It is not necessary to remove the panel, it can be left hanging. 4. Remove (2) Phillips screws from under the knee panel. 5. Unclip the knee panel and remove (1) Phillips screw exposed on the right side of the steering column. 6. Unclip and remove the entire dash trim bezel.
99-2001 CHEVROLET • Malibu 2001-03 / Malibu Classic 2004 Disconnect the negative battery terminal to prevent an accidental short circuit. DASH DISASSEMBLY 1. Unsnap and remove radio bezel. 16 2. Remove (3) 9/32" hex head screws and remove radio. Continue to kit assembly.
99-2001 CHEVROLET • Monte Carlo 2000-04 Disconnect the negative battery terminal to prevent an accidental short circuit. panel, it can remain hanging.) 2. Remove (2) 9/32" screws from the knee panel and unclip the panel. 3. Unsnap the driver's side fuse panel cover and remove (1) 9/32" screw. 4. Open the glove box and remove (1) 9/32" screw from the upper left corner. 5. Remove (3) 9/32" screws securing the factory radio and disconnect the wiring. Continue to kit assembly. DASH DISASSEMBLY 1.
99-2001 CHEVROLET • Trailblazer 2002-04 Disconnect the negative battery terminal to prevent an accidental short circuit. DASH DISASSEMBLY 1. Remove (2) Phillips screws inside instrument cluster. 18 2. Remove (1) Phillips screw under climate controls to the left of the power outlet. 3. Remove (2) 7mm hex heads from under steering column and lower the panel. Remove (3) Phillips screws around steering wheel. 4. Unsnap and remove bezel. (Use caution pulling over hazard switch.
99-2001 CHEVROLET • Venture 2000 OLDSMOBILE • Silhouette 2000 PONTIAC • Montana 2000 1. Remove the ashtray and (1) Phillips screw exposed in the ashtray cavity. 2. Remove (1) Phillips screw from the cigarette lighter compartment. 3. Remove (3) 9/32" hex-head screws securing the factory head unit and disconnect the wiring. Continue to kit assembly. DASH DISASSEMBLY Disconnect the negative battery terminal to prevent an accidental short circuit.
99-2001 DASH DISASSEMBLY CHEVROLET • Venture 2001-04 OLDSMOBILE • Silhouette 2001-04 PONTIAC • Montana 2001-04 20 Disconnect the negative battery terminal to prevent an accidental short circuit. 1. Open cup holders and remove (2) Phillips 7mm screws. 2. Unsnap and remove dual power outlet assembly from lower storage. 3. Open lower storage door and remove (2) 7mm screws inside. 4. Models with DVD - Remove DVD player and remove (2) 7 mm screws from behind and (2) 7 mm screws near the floor. 5.
99-2001 HUMMER • H2 2003-2004 Disconnect the negative battery terminal to prevent an accidental short circuit. remove box. 2. Remove (4) phillips screws from hinge on console door inside console and remove door. 3. Loosen (1) T-15 torx on forward facing side of shift lever and pull up to remove. 4. Unclip cup holder/shifter trim assembly and remove. 5. Remove (6) phillips screws from top of center console. 6. Remove (2) phillips screws from inside pocket on back of center console, then unclip and remove.
99-2001 HUMMER • H2 2003-2004 Disconnect the negative battery terminal to prevent an accidental short circuit. DASH DISASSEMBLY 7. 22 Remove (1) 10mm bolt to right of shift lever. 8. Remove (2) phillips screws from under console box on drivers side and (2) phillips screws from under console trim top on passenger side. 9. Slide control assembly rearward. 10. Remove (2) T-30 torx bolts from top of radio/climate control trim and unclip and remove. 11. Remove (3) 9/32” screws that hold the radio in.
99-2001 GMC • Envoy 2002-04 / ISUZU • Ascender 2003-04 OLDSMOBILE • Bravada 2002-04 Disconnect the negative battery terminal to prevent an accidental short circuit. below dash forward of center console. 2. Slide carpeted panel down and backwards to reveal (2) Phillips screws and remove. 3. Unsnap radio bezel and unplug cigarette lighter and accessories. 4. Remove (3) 9/32" hex head screws and remove radio. Continue to kit assembly. DASH DISASSEMBLY 1.
99-2001 OLDSMOBILE • Achieva 1996-98 DASH DISASSEMBLY Disconnect the negative battery terminal to prevent an accidental short circuit. 24 1. Open the glove box, press inward on the walls of the glove box liner and remove the liner. 2. Remove (10) torx-head screws from the glove box location. 3. Remove (2) 9/32" hex-head screws under the steering column. 4. Unclip the dash trim bezel. 5. Remove the screws securing the factory head unit and disconnect the wiring. Continue to kit assembly.
99-2001 OLDSMOBILE • Alero 1999-04 Disconnect the negative battery terminal to prevent an accidental short circuit. of shifter and pull upward. 2. Unclip and remove shifter trim panel. 3. Unclip and remove radio and climate control panel by pulling from bottom. 4. Remove (3) 9/32" screws from radio and remove. Continue to kit assembly. DASH DISASSEMBLY 1.
99-2001 OLDSMOBILE • Aurora 1995-03 DASH DISASSEMBLY Disconnect the negative battery terminal to prevent an accidental short circuit. 26 1. Unclip the radio trim bezel and remove. 2. Remove (3) 9/32" screws securing the factory head unit and disconnect the wiring. Continue to kit assembly.
99-2001 OLDSMOBILE • Cutlass 1997-99 Disconnect the negative battery terminal to prevent an accidental short circuit. 2. Remove (3) 7mm hex-head screws securing the factory head unit and disconnect the wiring. Continue to kit assembly. DASH DISASSEMBLY 1. Unclip the radio trim bezel and remove.
99-2001 OLDSMOBILE • Eighty Eight 1994-99 / Ninety Eight 1994-96 Disconnect the negative battery terminal to prevent an accidental short circuit. DASH DISASSEMBLY 1. Open the glove box and remove (2) hex-head screws securing the 28 wood trim. 2. Unsnap the wood trim and remove. 3. Remove (2) 9/32" hex-head screws below the radio trim bezel. 4. Lift up on the bezel and remove. 5. Remove (3) 9/32" hex-head screws securing the factory head unit and disconnect the wiring. Continue to kit assembly.
99-2001 OLDSMOBILE • Intrigue 1998-02 Disconnect the negative battery terminal to prevent an accidental short circuit. hex-head screws exposed. 2. Remove the center console. 3. Unclip the radio trim bezel and remove. 4. Remove (3) 9/32" hex-head screws securing the factory head unit and disconnect the wiring. Continue to kit assembly. DASH DISASSEMBLY 1.
99-2001 OLDSMOBILE • LSS 1996-99 / Regency 1997-98 Disconnect the negative battery terminal to prevent an accidental short circuit. DASH DISASSEMBLY 1. Open glove box and remove two-center trim bezels attached by screws. 30 2. Unsnap and remove radio trim bezel. 3. Remove (3) 9/32" hex-head screws and remove radio. Continue to kit assembly.
99-2001 PONTIAC • Aztec 2001-04 Disconnect the negative battery terminal to prevent an accidental short circuit. 2. Remove (1) Phillips screw exposed inside bottom cup holder. 3. Unsnap and remove shifter trim with cup holders. 4. Remove (2) #15 torx at bottom of radio / climate bezel. Continue to kit assembly. DASH DISASSEMBLY 1. Pull out cup holder inserts.
99-2001 PONTIAC • Bonneville 2000-04 DASH DISASSEMBLY Disconnect the negative battery terminal to prevent an accidental short circuit. 32 1. Remove (2) Phillips screws from the instrument cluster. 2. Unclip the ignition trim and remove. 3. Unclip the climate control / radio trim panel and remove. 4. Depress the spring clips on each side of the factory head unit and remove. Continue to kit assembly.
99-2001 PONTIAC • Grand Am 2001-04 Disconnect the negative battery terminal to prevent an accidental short circuit. 2. Remove (3) 9/32" screws from radio brackets and remove radio. Continue to kit assembly. DASH DISASSEMBLY 1. Unsnap and remove radio trim bezel.
99-2001 PONTIAC • Sunfire 2000-04 Disconnect the negative battery terminal to prevent an accidental short circuit. DASH DISASSEMBLY 1. Open the glove box and remove (2) Phillips screws exposed on the right 34 edge of the radio trim bezel. 2. Unclip the bezel and remove. 3. Remove (3) 9/32" hex-head screws securing the factory head unit and disconnect the wiring. Continue to kit assembly.
99-2001 CHEVROLET • Colorado 2004-2005 / GMC • Canyon 2004-2005 Disconnect the negative battery terminal to prevent an accidental short circuit. (Figure A) 2. Remove (3) 9/32” screws securing the radio to remove. (Figure B) Continue to kit assembly. Figure A DASH DISASSEMBLY 1. Unsnap and remove the entire panel surrounding the radio and A/C controls.
99-2001 ALL VEHICLES - DIN HEAD UNIT PROVISIONS Disconnect the negative battery terminal to prevent an accidental short circuit. KIT ASSEMBLY 1. Slide DIN cage into the Radio Housing and secure by bending metal locking tabs outward. (See Figure B) 2. Slide radio into DIN cage. (See Figure B) Note: When installing a DIN head unit you will need to cut and remove the shaft supports in the radio housing.
99-2001 ALL VEHICLES - SHAFT HEAD UNIT PROVISIONS Disconnect the negative battery terminal to prevent an accidental short circuit. Slide the aftermarket head unit into the kit from the back and secure with the shaft nuts provided with the new head unit. Note: If an equalizer will be included slide the unit into the back of the radio housing and secure. If an equalizer will NOT be included, snap the Equalizer Dummy Plate into the opening in the radio housing KIT ASSEMBLY 1.
99-2001 FINAL ASSEMBLY ALL VEHICLES A) Strip wire ends back 1/2" B) Twist ends together C) Solder D) Tape 1. Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) See figure A 2. Re-connect the battery terminal and test the unit for proper operation. 3.
99-2001 NOTES: NOTES 39
99-2001 1-800-221-0932 www.metraonline.com © COPYRIGHT 2004-2007 METRA ELECTRONICS CORPORATION Rev. 10-11-07 INST-2001 - Rev.