Specifications

ManualsBrandsMetra Manualschassis components99-2007

INSTALLATION INSTRUCTIONS FOR PART 99-2007

99-2007

APPLICATIONS

Cadillac Escalade

2007-2010

KIT FEATURES

• ISO Mount Radio Provision With Pocket

• Double DIN Radio Provision

• Stacked ISO Units Provision

A) Radio Housing • B) Radio Housing Trim Plate • C) Radio Housing Brackets • D) Pocket

• E) 4) #8 3/8” Screws

KIT COMPONENTS

Small Flat Blade Screwdriver/ Panel Removal Tool

• Phillips Screwdriver • Socket Set

1-800-221-0932

www.metraonline.com

TOOLS REQUIRED:

WIRING AND ANTENNA CONNECTIONS

(Sold Separately)

• 40-CR10 - 2002-up Chrysler/GM Antenna Adapter

• GMOS-LAN-05 - 2007-up GM LAN Digital Amp Interface

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 99-2007 APPLICATIONS Cadillac Escalade 2007-2010 99-2007 KIT FEATURES • ISO Mount Radio Provision With Pocket • Double DIN Radio Provision • Stacked ISO Units Provision KIT COMPONENTS A) Radio Housing • B) Radio Housing Trim Plate • C) Radio Housing Brackets • D) Pocket • E) 4) #8 3/8” Screws S S D C E WIRING AND ANTENNA CONNECTIONS A S (Sold Separately) • 40-CR10 - 2002-up Chrysler/GM Antenna Adapter • GMOS-LAN-05 - 2007-up GM LAN Digital Amp Interface B TOO
PAGE 2
99-2007 TABLE OF CONTENTS Dash Disassembly - Cadillac Escalade 2007-2010. . . . . . . . . . . . . . . . . . . . . . . . . . 1 Kit Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Kit Assembly - ISO Mount Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . 3 - Double DIN Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 - Stacked ISO Units Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 3
99-2007 DASH DISASSEMBLY CADILLAC ESCALADE 2007-2010 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove cup holder and ashtray assembly. (Figure A) 3 Unclip and remove the trim panel above the glove box including the a/c vent. (Figure B) 4 Unclip and remove the entire panel surrounding the radio including the a/c vents. (Figure C) B 5 Remove (6) 9/32” screws to extract radio from dash. (Figure D) Continue to kit assembly.
PAGE 4
99-2007 KIT PREPARATION CADILLAC ESCALADE 2007-2010 1 Cut and remove the shaded areas marked with an “S” only from the radio housing. (Figure A) Right side and top of Radio housing. (Figure B) Left side and top of Radio housing. NOTE: Do NOT remove the tab marked with both “S” and “E”. Continue to kit assembly.
PAGE 5
99-2007 KIT ASSEMBLY ISO MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Flip the radio housing brackets upside down then snap them to the inside edge of the radio housing. (Figure A) 2 Slide the pocket into the top of the opening aligning the holes in the radio housing brackets with the bosses on the pocket and secure using the provided (4) #8 3/8” screws.
PAGE 6
99-2007 KIT ASSEMBLY DOUBLE DIN RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Attach the radio housing brackets to the inside edge of the radio housing. (Figure A) 2 Slide the Double DIN radio into the radio housing bracket assembly and secure the unit using the screws supplied with the radio. (Figure B) 3 Snap the radio housing trim plate onto the front of the radio housing. (Figure C) B Continue to final assembly.
PAGE 7
99-2007 KIT ASSEMBLY STACKED ISO UNITS PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Attach the radio housing brackets to the inside edge of the radio housing. (Figure A) 2 Slide the stacked ISO units into the radio housing bracket assembly and secure the unit using the screws supplied with the units. (Figure B) 3 Snap the radio housing trim plate onto the front of the radio housing. (Figure C) B Continue to final assembly.
PAGE 8
99-2007 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder C D) Tape D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disassembly.