User Manual

ManualsBrandsMetra ManualsAutomotiveMetra 99-2021 Single DIN / Double DIN Installation Kit for 2005-up Buick Lacrosse Vehicles

INSTALLATION INSTRUCTIONS FOR PART 99-2021

99-2021

APPLICATIONS

BUICK Lacrosse

2005-2009

KIT FEATURES

• DIN Radio Provision with Pocket

• ISO Mount Radio Provision with Pocket

• Double DIN Radio Provision

• Stacked ISO Mount Units Provision

• A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets

• E) Double DIN Trim Plate • F) Pocket

KIT COMPONENTS

TOOLS REQUIRED:

Small Flat Blade Screwdriver/ Panel Removal Tool

• Phillips Screwdriver • Socket Set

1-800-221-0932

www.metraonline.com

WIRING AND ANTENNA CONNECTIONS (Sold Separately)

Wire harness:

• GMOS-01 GM interface 2002-up

• GMOS-04 GM amplified interface 2002-up

Antenna adapter:

• 40-GM10 -GM antenna adapter 1988-up

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 99-2021 APPLICATIONS BUICK Lacrosse 2005-2009 99-2021 KIT FEATURES • DIN Radio Provision with Pocket • ISO Mount Radio Provision with Pocket • Double DIN Radio Provision • Stacked ISO Mount Units Provision KIT COMPONENTS • A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets • E) Double DIN Trim Plate • F) Pocket A C B D WIRING AND ANTENNA CONNECTIONS (Sold Separately) Wire harness: • GMOS-01 GM interface 2002-up • GMOS-04 GM amplified int
PAGE 2
99-2021 TABLE OF CONTENTS Dash Disassembly - Buick Lacrosse 2005-2009 . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Kit Assembly - DIN Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 - ISO Mount Radio Provision with Pocket. . . . . . . . . . . . . . . . . . . . . . . . 3 - Double DIN Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - Stacked ISO Mount Units Provision . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 3
99-2021 DASH DISASSEMBLY BUICK LACROSSE 2005-2009 *Note: Refer also to the instructions included with the aftermarket radio. A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove trim panel below a/c control. (Figure A) 3 Remove (2) 9/32” screws securing climate controls to the sub dash. Unplug and remove climate controls. (Figure B) 4 Unclip trim panel above the radio. Unplug and remove the panel. (Figure C) B 5 Remove (4) 9/32” screws securing radio.
PAGE 4
99-2021 KIT ASSEMBLY DIN MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Slide the DIN cage into the radio housing and secure by bending the metal locking tabs outward. (Figure A) 2 Slide the aftermarket radio into the DIN cage and until it snaps into place. (Figure B) 3 Snap the pocket into the radio housing. (Figure C) Continue to final assembly.
PAGE 5
99-2021 KIT ASSEMBLY ISO MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Mount the ISO Brackets to the radio using the screws supplied with the radio. (Figure A) 2 Slide the radio into the radio housing until it snaps into place. (Figure B) 3 Snap the trim plate onto the front of the Radio Housing. (Figure B) 4 Snap the Pocket into the radio housing. (Figure C) B Continue to final assembly.
PAGE 6
99-2021 KIT ASSEMBLY DOUBLE DIN RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Cut and remove the center bar from the radio housing. (Figure A) 2 Snap the Double DIN brackets to the inside edge of the radio housing. (Figure B) 3 Slide the Double DIN radio into the DDIN bracket/radio housing assembly and secure the radio to the assembly using the screws supplied with the radio. (Figure C) B 4 Snap the Double DIN trim plate onto the front of the radio housing.
PAGE 7
99-2021 KIT ASSEMBLY STACKED ISO MOUNT UNITS PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Cut and remove the center bar from the radio housing. (Figure A) 2 Snap the Double DIN brackets to the inside edge of the radio housing. (Figure B) 3 Slide the stacked ISO mount units into the bracket/trim plate assembly and secure the units to the assembly using the screws supplied with the units.
PAGE 8
99-2021 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation.