Owner's Manual

ManualsBrandsMetra ManualsAudio accessories & installationDash Kit

5

6

7

8

9

:;;;tI1tt,.\,:::

· : ,

·.

;:i\

. . . ,

'}:•

Z-:~1Rlf-,'~J,:;;t=.:~

~:-{t.~;:

. ·

1

:

~!~;1t:~\:'v,

:.

~,n,

:->~:~_\J

_~:~,-,l;',~

.

~

~

·.'A;

.

;;i;,,:

-

Connection!i

to

be

made

•

Connect

the

Green/Black

wire

to

the

left

rear

negative

speaker

output.

•

Connect

the

Purple

wire

to

the

right

rear

positive

speaker

output

of

the

aftermarket

radio.

•

Connect

the

Purple/Black

wire

to

the

right

rear

negative

speaker

output

of

the

aftermarket

radio.

•

Connect

the

RCA

jacks

to

the

audio

AUX-IN

jacks

(if

applicable).

Note:

(a)

This

will

allow

you

to

retain

the

3.5

AUX-IN

jack

in

the

console.

(b)

The

3.5

jack

can

only

be

used

if

it

is

a

single

AUX-IN

jack.

(c)

If

the

AUX-IN

jack

has

a

USB

port,

neither

can

be

used.

12-pin

pre-wired

ASWC-1

harness:

•

This

harness

is

to

be

used

along

with

the

optional

ASWC-1

(not

included)

to

retain

steering

wheel

audio

controls.

If

the

ASWC-1

is

not

being

used,

disregard

this

harness.

If it

will

be

used,

please

refer

to

the

ASWC-1

instructions

for

radio

connections

and

programming.

Note:

Disregard

the

hamess

that

comes

with

the

ASWC-1.

•

Connect

the

Red

wire

to

the

accessory

wire.

Note:

The

relay

attached

to

the

GMOS-044

is

only

for

audible

turn

signal

clicks.

No

extra

steps

are

required

to

retain

this,

so

leave

it

as-is.

3

ln!italling

the

liMD!i-044

With

the

key

in

the

off

position:

•

Connect

the

GMOS-044

harness

into

the

interface,

and

then

into

the

vehicle.

Initializing

the

liMD!i-044

Attention!

If

the

interface

loses

power

for

any

reason,

the

following

steps

will

need

to

be

performed

again.

Also,

if

installing

an

ASWC-1

connect

it

after

you

initialize

and

test

the

interface/radio,

with

the

key

in

the

off

position.

•

Turn

the

key

(or

push-to-start

button)

to

the

ignition

position

and

wait

until

the

radio

comes

on.

Note:

If

the

radio

does

not

come

on

within

60

seconds,

tum

the

key

to

the

off

position,

disconnect

the

interface,

check

all

connections,

reconnect

the

interface,

and

then

try

again

.

•

Turn

the

key

to

the

off

position,

and

then

to

the

accessory

position.

Test

all

functions

of

the

installation

for

proper

operation,

before

reassembling

the

dash.

·•