Owner's Manual

ManualsBrandsMetra ManualsAutomotiveMetra 99-5719 2004-2007 Ford Tarus/Mercury Sable Electronic Climate Control Radio Install Kit (Black)

Metra. The World’s Best Kits.

INSTALLATION INSTRUCTIONS

99-5719

Attention! Let the vehicle sit with the key

out of the ignition for a few minutes before

removing the factory radio. When testing the

aftermarket equipment, ensure that all factory

equipment is connected before cycling the

key to ignition.

KIT FEATURES

• DIN radio provision with pocket

• ISO DIN radio provision with pocket

• ISO DDIN radio provision

• Integrated auto climate controls and display

• Integrated passenger airbag light

• Painted scratch resistant matte black

KIT COMPONENTS

• A) Radio housing • B) ISO Brackets • C) ISO trim plate • D) Pocket • E) ISO DDIN brackets • F) ISO DDIN trim plate • G) Temperature sensor housing

• H) Wiring harness (not shown)

TOOLS REQUIRED

• Radio removal tool (Metra part #86-5618)

• Phillips screwdriver • Panel removal tool

• Cutting tool • T-10 torx screwdirver

TABLE OF CONTENTS

Dash Disassembly ..................................................2

Kit Preparation .......................................................3

Kit Assembly

–DIN radio provision with pocket ........................4

–ISO DIN radio provision with pocket ..................5

–ISO DDIN radio provision .....................................6

Audio Wiring ..........................................................7

WIRING & ANTENNA CONNECTIONS

Wiring Harness: Included with kit

Antenna Adapter: Included with kit

F G

B C D E

Ford Taurus / Mercury Sable

(with auto climate) 2004-2007

Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle

speciﬁc applications

Summary of content (8 pages)

PAGE 1
99-5719 I N S TA L L AT I O N I N S T R U C T I O N S Ford Taurus / Mercury Sable (with auto climate) 2004-2007 Visit MetraOnline.
PAGE 2
DASH DISASSEMBLY 1. Using Metra’s 86-5618, pull the radio/ climate control panel from the dash. (Figure A) 2. Disconnect the audio system connectors, blower motor switch connector, vacuum hose harness, a/c damper door switch connector, and potentiometer connector. Remove the panel. Continue to Kit Preparation (Figure A) 2 1.800.221.0932 | MetraOnline.
PAGE 3
KIT PREPARATION 1. Remove the temperature sensor assembly from the back of the radio/ climate control panel. Insert the assembly into the temperature sensor housing, then secure the assembly under the dash. Ensure that the vent opening is not blocked. This is what monitors the temperature in the vehicle for the climate control to function properly. 2. Remove (2) T-10 Torx screws securing the mounting clips to the sides of the radio/ climate control panel, then remove the clips. (Figure A) 2 Fig.
PAGE 4
KIT ASSEMBLY DIN radio provision with pocket 1. Remove the metal DIN sleeve from the aftermarket radio. 2. Slide the sleeve into the top opening of the radio housing and secure by bending the metal locking tabs down. (Figure B) 3. Snap the pocket into the bottom opening of the radio housing. (Figure B) 4. Slide the radio back into the sleeve until it clicks in. (Figure B) Continue to Audio Wiring 4 (Figure A) (Figure B) 1.800.221.0932 | MetraOnline.
PAGE 5
KIT ASSEMBLY ISO DIN radio provision with pocket 1. Remove the metal DIN sleeve and trim ring from the aftermarket radio. 2. Secure the ISO brackets to the radio using the screws supplied with the radio. (Figure A) 3. Slide the radio into the top opening of the radio housing until the side clips engage. (Figure B) 4. Snap the pocket into the bottom opening of the radio housing. (Figure B) 5. Snap the trim plate into the radio housing. (Figure A) (Figure B) Continue to Audio Wiring REV.
PAGE 6
KIT ASSEMBLY ISO DDIN radio provision 1. Cut and remove the center bar from the radio housing. (Figure A) 2. Snap the ISO DDIN brackets to the inside edge of the radio housing opening. 3. Slide the radio into the bracket/housing assembly, then secure using the screws supplied with the radio. (Figure B) (Figure B) 4. Snap the ISO DDIN trim plate into the radio housing. (Figure B) Continue to Audio Wiring 6 (Figure A) (Figure B) 1.800.221.0932 | MetraOnline.
PAGE 7
AUDIO WIRING This vehicle utilizes a remote radio brain and must be bypassed to work with an aftermarket radio. Radio Brain 1. Open the trunk, remove (4) pop-clips from the driver’s side trunk liner, then remove the liner. (Figure A) 2. Locate the radio brain on the top of the wheelwell. Disconnect the speaker and antenna connectors, then connect the wiring harness provided with the kit to those connectors. Nothing will connect back to the tuner brain as it will be bypassed. (Figure B) 3.
PAGE 8
99-5719 I N S TA L L AT I O N I N S T R U C T I O N S If you are having difficulties with the installation of this product, contact our Tech Support line either by phone at 1-800-253-TECH, or email at techsupport@metra-autosound.com. Before doing so, look over the instruction booklet a second time and ensure that the installation was performed exactly as the instruction booklet is stated. Have the vehicle apart and ready to perform troubleshooting steps before contacting Metra/Axxess Tech Support.