User Manual

ManualsBrandsMetra ManualsAutomotiveMetra 99-5821B Single or Double DIN Installation Dash Kit for 2010 Ford Fusion and Mercury Milan (Matte Black)

INSTALLATION INSTRUCTIONS FOR PART 99-5821B

• A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets

• E) Double DIN Trim Plate • F) Pocket

KIT COMPONENTS

C DE

1-800-221-0932

www.metraonline.com

WIRING AND ANTENNA CONNECTIONS

(Sold Separately)

Wire harness:

• XSVI-5520-NAV Ford Interface 2006-up

• AFSI-02 -Ford SYNC Interface 2007-up

Antenna adapter:

• 40-CR10 Ford/Chrysler antenna adapter

TOOLS REQUIRED:

Small Flat Blade Screwdriver • Panel Removal Tool

Phillips Screwdriver • Socket Set

APPLICATIONS

FORD Fusion/

MERCURY Milan 2010-up

(Non Factory NAV)

99-5821B

KIT FEATURES

• DIN Head Unit Provision with Pocket

• ISO DIN Head Unit Provision with Pocket

• Double DIN Head Unit Provision

• ISO Stacked Head Unit Provision

• Painted Matte Black

99-5812BL - Blue

99-5812S - Silver

99-5812R - Red

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 99-5821B APPLICATIONS FORD Fusion/ MERCURY Milan 2010-up (Non Factory NAV) 99-5821B KIT FEATURES • DIN Head Unit Provision with Pocket • ISO DIN Head Unit Provision with Pocket • Double DIN Head Unit Provision • ISO Stacked Head Unit Provision • Painted Matte Black 99-5812BL - Blue 99-5812S - Silver 99-5812R - Red KIT COMPONENTS • A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets • E) Double DIN Trim Plate • F) Pocket A B C D E WIRIN
PAGE 2
99-5821B TABLE OF CONTENTS Dash Disassembly - Ford Fusion/Mercury Milan 2010-up (Non factory NAV) . . . . . . . . . . . . . . .1,2 Kit Assembly - Kit Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - DIN Head Unit Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 - ISO DIN Head Unit Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 3
99-5821B DASH DISASSEMBLY FORD FUSION/ MERCURY MILAN (NON FACTORY NAV) 2010-UP A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unsnap and remove cup holders/ shifter trim from top of center console. (Figure A) 3 Unsnap and remove coin tray from front of center console. (Figure B) 4 Open upper dash pocket, remove two 8mm screws from inside pocket, and remove pocket/ vent assembly. (Figure C) Note: Some models have a safety strap attached to this pocket/ vent panel.
PAGE 4
99-5821B DASH DISASSEMBLY FORD FUSION/ MERCURY MILAN (NON FACTORY NAV) 2010-UP 5 Remove two 7 mm screws from top of radio/climate panel. D 6 Unsnap and remove radio/ climate panel. (Figure D) 7 Remove climate controls (4 T-20’s) and lower three button switch plate (snap) from factory radio/ climate panel. (Retain for kit assembly) (Figure E) 8 Remove (6) metal “snap in” clips from back of factory panel and save to re-attach to the Metra radio housing during kit assembly.
PAGE 5
99-5821B KIT ASSEMBLY KIT PREPARATION 1 Mount the climate controls to the Metra radio housing using the factory hardware. (Figure A) A 2 Snap the three button switch plate into the Metra Radio housing. (Figure B) 3 Re-attach (6) metal “snap in” clips previously saved from back of factory panel and attach to the Metra housing. (Figure C) Continue to kit assembly.
PAGE 6
99-5821B KIT ASSEMBLY DIN HEAD UNIT PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation. 2 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure A) 3 Snap the pocket into the bottom opening of the radio housing.
PAGE 7
99-5821B KIT ASSEMBLY ISO DIN HEAD UNIT PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation. 2 Mount the ISO Brackets to the head unit with the screws supplied with the unit. (Figure A) 3 Snap the pocket into the bottom opening of the radio housing.
PAGE 8
99-5821B KIT ASSEMBLY DOUBLE DIN HEAD UNIT PROVISION/ STACKED ISO DIN HEAD UNIT PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation. 2 Cut and remove the center bar from the radio housing.