Installation instructions

ManualsBrandsMetra ManualsMobile Phones99-6518B

METRA. The World’s best kits.

™

metraonline.com1-800-221-0932

REV. 7/23/2014 INST99-6518

CAUTION: Metra recommends disconnecting the

negative battery terminal before beginning any

installation. All accessories, switches, and especially

air bag indicator lights must be plugged in before

reconnecting the battery or cycling the ignition.

NOTE: Refer to the instructions included with the

aftermarket radio.

INSTALLATION INSTRUCTIONS FOR PART 99-6518B

APPLICATIONS

Table of Contents

• ISO DIN radio provisions with pocket

• Painted matte black

KIT FEATURES

KIT COMPONENTS

WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness: • XSVI-6523-NAV Chrysler interface 2013-up • AX-LCD

Antenna Adapter: • 40-EU55

• Panel removal tool • Phillips screwdriver

• Socket Wrench

TOOLS REQUIRED

CB D

Dash Disassembly

– Dodge Ram 2013-up ............................................ 2

Kit Assembly

–

ISO DIN radio provision with pocket ...................... 3

• A) Radio housing • B) Brackets • C) Pocket • D) (4) #8 x 3/8” Phillips screws

Ram Trucks 2013-up (without 8.4 inch touchscreen)

Modifications to factory radio cavity required for this installation

99-6518B

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 99-6518B APPLICATIONS Table of Contents Ram Trucks 2013-up (without 8.4 inch touchscreen) Modifications to factory radio cavity required for this installation 99-6518B Dash Disassembly –. Dodge Ram 2013-up............................................. 2 Kit Assembly –. ISO DIN radio provision with pocket.......................
PAGE 2
99-6518 Dash Disassembly 1. Remove liner inside tray at the top center of the dash and remove two torx screws. (Figure A) 2. Unsnap and remove radio panel. (Figure B) 3. Remove four screws and remove radio. (Figure C) 4. The factory rear support will need to be cut or removed to allow space for a new radio. The bottom section can be removed with two cuts at the bottom corners.
PAGE 3
99-6518 Kit Assembly 4. Locate the factory wiring harness and antenna plug in the dash. Metra recommends using the proper mating adapters from Metra and/or AXXESS. ISO DIN radio provisions Note: For proper orientation, the locating tabs on the Radio Housing are more to the top of the kit than bottom. (Figure A) Top of housing 5. Reassemble dash in reverse order of disassembly. 1. Rotate the brackets into the radio housing. (Figure B) 2.
PAGE 4
INSTALLATION INSTRUCTIONS FOR PART 99-6518 KNOWLEDGE IS POWER REV. 7/23/2014 INST99-6518 Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians METRA. The World’s best kits.™ 1-800-221-0932 metraonline.
PAGE 5
INSTRUCCIONES DE INSTALACIÓN PARA LA PIEZA 99-6518B APLICACIONES Tabla de contenido Ram Trucks 2013 y mas (sin pantalla táctil de 8.4 pulgadas) Se requieren modificaciones a la cavidad del radio de fábrica para esta instalación. 99-6518B Desmontaje del tablero –. Dodge Ram 2013 y mas........................................ 2 Ensamble del kit –. Provisión de radio ISO DIN con bolsillo..................
PAGE 6
99-6518 Desmontaje del tablero 1. Quite el revestimiento interior de la charola en la parte superior central del tablero y quite los dos tornillos torx. (Figura A) 2. Suelte a presión y quite el panel del radio. (Figura B) 3. Quite los cuatro tornillos y quite el radio. (Figura C) 4. El soporte trasero de fábrica deberá cortarse o quitarse para hacer espacio para un nuevo radio. La sección inferior puede quitarse con dos cortes en las esquinas inferiores.
PAGE 7
99-6518 Ensamble del kit Provisión de radio ISO DIN con bolsillos 4. Ubique el arnés de cableado de fábrica y el conector de la antena en el tablero. Metra recomienda el uso de adaptadores adecuados de acoplamiento de Metra y/o de AXXESS. Parte superior de la carcasa Nota: Para una correcta orientación, las pestañas localizadoras de la carcasa del radio están más cerca de la parte superior del kit que de la parte inferior. (Figura A) 5. Vuelva a armar el tablero al revés de como lo desarmó. 1.
PAGE 8
INSTRUCCIONES DE INSTALACIÓN PARA LA PIEZA 99-6518B EL CONOCIMIENTO ES PODER sus habilidades deIS instalación y KMejore NOWLEDGE POWER REV. 7/23/2014 INST99-6518 Enhance your installation and fabrication skills by fabricación inscribiéndose en la escuela de enrolling in the most recognized and respected dispositivos electrónicos móviles más reconocida mobile electronics school in our industry. y respetada de nuestra industria. en Log onto www.installerinstitute.