User Manual

ManualsBrandsMetra ManualsAutomotiveMetra 99-7010 Single DIN / Double DIN Installation Kit for 2006-2007 Mitsubishi Eclipse Vehicles

METRA. The World’s best kits.

™

metraonline.com1-800-221-0932

REV. 5/6/2014 INST99-7010

CAUTION: Metra recommends disconnecting the

negative battery terminal before beginning any

installation. All accessories, switches, and especially

air bag indicator lights must be plugged in before

reconnecting the battery or cycling the ignition.

NOTE: Refer to the instructions included with the

aftermarket radio.

INSTALLATION INSTRUCTIONS FOR PART 99-7010

• A) Radio housing • B) ISO brackets • C) ISO trim plate • D) Double DIN bracket • E) Pocket

• F) Double DIN trim plate

KIT COMPONENTS

• DIN radio provision with pocket

• ISO DIN radio provision with pocket

• Double DIN radio provision

• Painted silver to match factory dash

KIT FEATURES

WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness: • MITO-01 - Mitsubishi amp interface 2006-up • 70-7001 - Mitsubishi 1992-up

Antenna Adapter: • Not required

• Phillips screwdriver • Small flat blade screwdriver

TOOLS REQUIRED

Mitsubishi Eclipse/Eclipse Spyder 2006-2012

99-7010

A B C D

Dash Disassembly

– Mitsubishi Eclipse/Eclipse Spyder 2006-2012 ...... 2

Kit Assembly

– Radio housing assembly....................................... 2

– DIN radio provision with pocket ............................ 3

– ISO DIN radio provision with pocket ...................... 3

– Double DIN radio provision ............................(back)

Table of Contents

E F

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 99-7010 Mitsubishi Eclipse/Eclipse Spyder 2006-2012 99-7010 Table of Contents Dash Disassembly – Mitsubishi Eclipse/Eclipse Spyder 2006-2012....... 2 KIT FEATURES • DIN radio provision with pocket • ISO DIN radio provision with pocket • Double DIN radio provision • Painted silver to match factory dash Kit Assembly – Radio housing assembly....................................... 2 – DIN radio provision with pocket.............................
PAGE 2
Dash Disassembly Kit Assembly Mitsubishi Eclipse/Eclipse Spyder 2006-2012 Radio housing assembly 1. Clip the A/C vents into the 99-7010 radio housing. (Figure A) 1. Unclip and remove the trim panel including the radio A/C vents. (Figure A) 2. Clip the hazard switch into the 99-7010 radio housing. (Figure B) 2. Remove (4) Phillips screws securing radio chassis to dash to remove. (Figure B) 3. Unclip and remove the A/C vents from the factory radio trim panel.
PAGE 3
Kit Assembly DIN radio provision with pocket ISO DIN radio provision with pocket 1. Slide the DIN cage into the kit and secure by bending the metal locking tabs down. (Figure A) 1. Mount the ISO brackets to the radio with the screws supplied with the radio. (Figure A) 2. Slide the radio into the kit until the side clips engage. 2. Slide the aftermarket radio into the cage and secure. (Figure B) 3. Snap the ISO trim plate into the radio housing. (Figure B) 3. Snap the pocket into the kit.
PAGE 4
INSTALLATION INSTRUCTIONS FOR PART 99-7010 Double DIN radio provision 1. Cut the center bar rib. (Figure A) 2. Slide the appropriate bracket into the kit aligning the holes in the kit with the holes on the bracket. 3. Slide the double DIN radio radio into the double DIN bracket/radio housing assembly and secure the radio to the kit using the screws supplied with the radio. (Figure B) REV. 5/6/2014 INST99-7010 4. Snap the double DIN trim plate into the kit. (Figure B) Cut center bar rib (Figure A) 5.
PAGE 5
INSTRUCCIONES DE INSTALACIÓN PARA LA PIEZA 99-7010 Mitsubishi Eclipse/Eclipse Spyder 2006-2012 99-7010 Indice Desmontaje del tablero – Mitsubishi Eclipse/Eclipse Spyder 2006-2012....... 2 CARACTERÍSTICAS DEL KIT • Provisión de radio DIN con bolsillo • Provisión de radio ISO DIN con bolsillo • Provisión de radio doble DIN • Pintada en plata para igualar el acabado de fábrica Ensamble del kit – Ensamble de la carcasa del radio.......................... 2 – Provisión de radio DIN con bolsillo..............
PAGE 6
Desmontaje del tablero Ensamble del kit Mitsubishi Eclipse/Eclipse Spyder 2006-2012 Ensamble de la carcasa del radio 1. Desenganche y quite el panel de moldura, incluyendo las rejillas del aire acondicionado del radio. (Figura A) 1. Enganche las rejillas del aire acondicionado en la carcasa del radio 99-7010. (Figura A) 2. Quite los (4) tornillos Phillips que sujetan el chasís del radio al tablero y retire. (Figura B) 2.
PAGE 7
Ensamble del kit Provisión de radio DIN con bolsillo Provisión de radio ISO DIN con bolsillo 1. Deslice la reja DIN en la carcasa del radio y sujétela doblando hacia abajo las pestañas de metal. (Figure A) 1. Monte los soportes ISO en la unidad central con los tornillos incluidos con la unidad. (Figure A) 2. Deslice la unidad central en la apertura del radio hasta que los ganchos laterales entren a presión. 2. Deslice la unidad central de mercado secundario en la reja y sujétela. (Figure B) 3.
PAGE 8
INSTRUCCIONES DE INSTALACIÓN PARA LA PIEZA 99-7010 Provisión de radio doble DIN 1. Corte la costilla de la barra central. (Figure A) 2. Deslice el soporte correspondiente en la carcasa del radio, alineando los orificios de la carcasa con los orificios del soporte. 3. Deslice la unidad de radio DDIN en el soporte/ensamble de carcasa del radio DDIN y sujete la unidad al kit utilizando los tornillos suministrados con la unidad. (Figure B) REV. 5/6/2014 INST99-7010 4.