User Manual

ManualsBrandsMetra ManualsAutomotiveMetra 99-7332 Installation Kit for 2007-up Radio Delete Hyundai Elantra Vehicles (Black)

INSTALLATION INSTRUCTIONS FOR PART 99-7332

99-7332

KIT FEATURES

• DIN Radio Provision with Pocket

• ISO Radio Provision with Pocket

A) Radio Housing B) ISO Brackets C) Trim Plate

KIT COMPONENTS

Small Flat Blade Screwdriver/ Panel Removal Tool

• Phillips Screwdriver

1-800-221-0932

www.metraonline.com

TOOLS REQUIRED:

APPLICATIONS

Hyundai Elantra

(Radio Delete Models)

2007-2010

Wiring &

Antenna Connections (sold separately)

• 70-1004 - Hyundai 2006-up / Kia2004-up Harness

• 70-7303 - Hyundai / Kia Harness 2009

• 40-KI11 - Kia Antenna Adapter 2007-up

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 99-7332 APPLICATIONS Hyundai Elantra (Radio Delete Models) 2007-2010 99-7332 KIT FEATURES • DIN Radio Provision with Pocket • ISO Radio Provision with Pocket KIT COMPONENTS A) Radio Housing B) ISO Brackets C) Trim Plate C B A Wiring & Antenna Connections (sold separately) • 70-1004 - Hyundai 2006-up / Kia2004-up Harness • 70-7303 - Hyundai / Kia Harness 2009 • 40-KI11 - Kia Antenna Adapter 2007-up TOOLS REQUIRED: Small Flat Blade Screwdriver/ Panel Removal Tool • P
PAGE 2
99-7332 TABLE OF CONTENTS Dash Disassembly - Hyundai Elantra (Radio Delete Models) 2007-2010 . . . . . . . . . . . . . . . . . . . . 1 Kit Assembly - DIN Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - ISO Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 3
99-7332 DASH DISASSEMBLY HYUNDAI ELANTRA (RADIO DELETE MODELS) 2007-2010 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip the panel surrounding the radio including the a/c vents and hazard switch. Unplug the hazard switch and remove the panel. (Figure A) A/C 3 Remove (4) Phillips screws securing the blank plate/pocket covering the radio cavity and remove the plate. (Figure B) 1 2 3 4 Continue to kit assembly.
PAGE 4
99-7332 KIT ASSEMBLY DIN RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs outward. (Figure A) 2 Slide the aftermarket radio into the cage until it snaps into place. (Figure B) Continue to final assembly.
PAGE 5
99-7332 KIT ASSEMBLY ISO RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Mount the ISO Brackets to the aftermarket radio using the screws supplied with the radio. (Figure A) 2 Slide the radio into the radio opening until the side clips snap into place. (Figure B) 3 Snap the trim plate onto the front of the Radio Housing. (Figure B) Continue to final assembly.
PAGE 6
99-7332 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disassembly.
PAGE 7
99-7332 NOTES 5
PAGE 8
99-7332 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV.