User Manual

ManualsBrandsMetra ManualsAutomotiveMetra 99-7345B Kia Optima 2011-UP Single/Double DIN Dash Fitment Kit with Pocket

METRA. The World’s best kits.

™

metraonline.com

REV. 8/19/2015 INST99-7345B

Installation instructions for part 99-7345B

CAUTION!

Metra recommends disconnecting the negative bat

tery terminal before beginning any installation, unless the vehicle

manufacturer recommends against so. Please check with your local

Dealership for more information. All accessories, switches, climate

controls panels, and especially air bag indicator lights must be con

nected before reconnecting the battery or cycling the ignition. Also,

do not remove the factory radio with the key in the on position, or the

vehicle running. It would be best to remove the key from the ignition

and then wait a few seconds before removing the factory radio.

• ISO DIN radio provision with pocket

• Painted matte black match factory dash

• A) Radio Brackets • B) Radio trim panel • C) Pocket • D) (3) #8 x 3/8” Phillips pan head screws

• E) (4) #8 x 3/8” Phillips truss head screws

KIT FEATURES

KIT COMPONENTS

WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness: • Non Amplified System - 70-7304 - Hyundai/Kia 2010-up

• Amplified System - HYBL-04 Hyundai/Kia 2010-up

Antenna Adapter: • Not required

• Panel Removal Tool • Phillips Screwdriver

TOOLS REQUIRED

Kia Optima 2011-2013

99-7345B

Dash Disassembly ..............................................2-3

Kit Preparation ....................................................... 3

Kit Assembly

– ISO DIN radio provision with pocket ...................... 4

Table of Contents

B C D

Summary of content (8 pages)

PAGE 1
Installation instructions for part 99-7345B Table of Contents Kia Optima 2011-2013 99-7345B Dash Disassembly...............................................2-3 Kit Preparation........................................................ 3 Kit Assembly KIT FEATURES • ISO DIN radio provision with pocket • Painted matte black match factory dash –. ISO DIN radio provision with pocket.......................
PAGE 2
99-7345B Dash Disassembly 1. Unsnap and remove the trim from around the radio and climate control. (Figure A) 5. Remove (5) Phillips screws from the instrument cluster panel, and then pull the panel out towards the steering wheel. Unplug all harnesses, making sure not to damage any wires or connectors in the process. (Figure E) 2. Unsnap the driver’s side panel from the outside edge of the dash. (Figure B) 3.
PAGE 3
99-7345B Dash Disassembly Kit Preparation 1. Remove (3) Phillips screws securing the vent on the factory radio trim panel and then remove. (Figure A) 7. Remove (6) Phillips screws securing the radio trim panel and then remove. (Figure G) 8. Remove (4) Phillips screws, (2 above and 2 below) from the radio assembly, then unplug and remove the radio. (Figure H) 2. Install the factory vent to the radio trim panel using (3) #8 x 3/8” Phillips pan head screws supplied.
PAGE 4
Installation instructions for part 99-7345B Kit Assembly IMPORTANT ISO DIN radio provision with pocket If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling. 1.
PAGE 5
Instrucciones de instalación para la pieza 99-7345B Indice Kia Optima 2011-2013 99-7345B Desmontaje Dash.................................................2-3 Preparación del kit................................................. 3 Ensamble del kit CARACTERÍSTICAS DEL KIT • Provisión de radio ISO DIN con cavidad • Pintura negro mate para igualar el tablero de fábrica –. Provisión de radio ISO DIN con cavidad.................
PAGE 6
99-7345B Desmontaje Dash 5. Sacar (5) tornillos Phillips del panel del cuadro de instrumentos, y luego tire del panel hacia el volante. Desconecte todos los arneses, asegurándose de no dañar los cables o conectores en el proceso. (Figura E) 1. Suelte a presión y quite de moldura de cada de todo el control de la radio y el clima. (Figura A) 2. Suelte el panel del lado del conductor desde el borde exterior del tablero. (Figura B) 3.
PAGE 7
99-7345B Preparación del kit Desmontaje Dash 1. Quite los (2) tornillos Phillips que sujetan el rejilla de ventilación en el panel de ajuste de radio de fábrica y luego quitar. (Figura A) 7. Quite los (6) tornillos de cabeza Phillips que sujetan el panel de la moldura del radio y retire. (Figura G) 8. Quite los (4) tornillos Phillips que sujetan el chasís del radio y el ensamble del soporte del aire acondicionado y el amplificador y luego quite el ensamble del tablero.
PAGE 8
Instrucciones de instalación para la pieza 99-7345B Ensamble del kit Provisión de radio ISO DIN con cavidad Si tiene dificultades con la instalación de este producto, llame a nuestra línea de soporte técnico al 1-800-253-TECH. Antes de hacerlo, revise las instrucciones por segunda vez y asegúrese de que la instalación se haya realizado exactamente como se indica en las instrucciones. Por favor tenga el vehículo desarmado y listo para ejecutar los pasos de resolución de problemas antes de llamar. 1.