User Manual

ManualsBrandsMetra ManualsAutomotiveMetra '07-08 Honda Fit Radio Install Kit

INSTALLATION INSTRUCTIONS FOR PART 99-7872

99-7872

APPLICATIONS

Honda Fit 2007-2008

KIT FEATURES

• DIN Radio Provision with Pocket

• ISO Mount Radio Provision with Pocket

• Double DIN Radio Provision

• Stacked ISO Mount Units Provision

•

Painted To Match Factory Dash

99-7872=Gray

• A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets

• E) Double DIN Trim Plate • F) Pocket

KIT COMPONENTS

Small Flat Blade Screwdriver/ Panel Removal Tool

• Phillips Screwdriver • Socket Set

1-800-221-0932

www.metraonline.com

WIRING AND ANTENNA CONNECTIONS

(Sold Separately)

Harness:

• 70-1722 - Honda harness 2006-up

Antenna Adapter:

• 40-HD10 - Honda antenna adapter

2005-up

TOOLS REQUIRED:

Summary of content (12 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 99-7872 APPLICATIONS Honda Fit 2007-2008 99-7872 KIT FEATURES • DIN Radio Provision with Pocket • ISO Mount Radio Provision with Pocket • Double DIN Radio Provision • Stacked ISO Mount Units Provision • Painted To Match Factory Dash 99-7872=Gray KIT COMPONENTS • A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets • E) Double DIN Trim Plate • F) Pocket C B A E D WIRING AND ANTENNA CONNECTIONS (Sold Separately) Harness: • 70-1722 - Honda
PAGE 2
99-7872 TABLE OF CONTENTS Dash Disassembly - Honda Fit 2007-2008 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1,2 Kit Assembly - Kit Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - DIN Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 - ISO Mount Radio Provision with Pocket. . . . . . . . . . . . . . . . . . . . . . . . 5 - Double DIN Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 3
99-7872 DASH DISASSEMBLY HONDA FIT 2007-2008 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Squeeze sides of glove box then pull out and let hang to access cables behind it. 3 Unclip the (3) a/c control cables behind glove box. (Figure A) 4 Remove (1) Phillips screw from the panel on the bottom of the a/c controls then unclip and remove the panel.
PAGE 4
99-7872 DASH DISASSEMBLY HONDA FIT 2007-2008 D 6 Unclip and remove the A/C & Rear Defroster switches and the Passenger Air Bag Off Light and set them aside for use during kit assembly. (Figure D) 7 Remove (8) Phillips screws securing the climate control to the back of the factory center panel. Remove climate controls and set aside for use during kit assembly.
PAGE 5
99-7872 KIT PREPARATION KIT PREPARATION A 1 Secure the climate controls into the radio housing using the factory hardware. (Figure A) 2 Snap the A/C & Rear Defroster switches and the Passenger Air Bag Off Light into the radio housing. (Figure B) 3 Attach the (7) retaining clips to the radio housing in the same location as removed from the factory center panel. (Figure C) B Continue to kit assembly.
PAGE 6
99-7872 KIT ASSEMBLY DIN MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Slide the DIN cage into the radio housing and secure by bending the metal locking tabs outward. (Figure A) 2 Slide the aftermarket radio into the DIN cage and until it snaps into place. (Figure B) 3 Snap the pocket into the radio housing. (Figure C) Continue to final assembly.
PAGE 7
99-7872 KIT ASSEMBLY ISO MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Mount the ISO Brackets to the radio using the screws supplied with the radio. (Figure A) 2 Slide the radio into the radio housing until it snaps into place. (Figure B) 3 Snap the trim plate onto the front of the Radio Housing. (Figure B) 4 Snap the Pocket into the radio housing. (Figure C) B Continue to final assembly.
PAGE 8
99-7872 KIT ASSEMBLY DOUBLE DIN RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Cut and remove the center bar from the radio housing. (Figure A) 2 Snap the Double DIN brackets to the inside edge of the radio housing. (Figure B) 3 Slide the Double DIN radio into the DDIN bracket/radio housing assembly and secure the radio to the assembly using the screws supplied with the radio.
PAGE 9
9-7872 KIT ASSEMBLY STACKED ISO MOUNT UNITS PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Cut and remove the center bar from the radio housing. (Figure A) 2 Snap the Double DIN brackets to the inside edge of the radio housing. (Figure B) 3 Slide the stacked ISO mount units into the bracket/housing assembly and secure the units to the assembly using the screws supplied with the units.
PAGE 10
99-7872 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation.
PAGE 11
99-7872 NOTES 9
PAGE 12
99-7872 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV.