User Manual

ManualsBrandsMetra ManualsAudio & Video AccessoriesMetra 99-7875T Single/Double DIN Installation Kit for 2008-2009 Honda Accord Vehicles with Dual Zone Climate Control, Taupe

INSTALLATION INSTRUCTIONS FOR PART 99-7875/99-7875T

99-7875/99-7875T

APPLICATIONS

Honda Accord 2008-up

(For Non-Navigation models with Dual Zone Climate controls)

Honda Accord Crosstour 2010-up

KIT FEATURES

• Painted To Match Factory Dash

99-7875=Charcoal, 99-7875T=Taupe

• DIN Radio Provision with Pocket

• ISO Mount Radio Provision with Pocket

• Double DIN Radio Provision

• Stacked ISO Mount Units Provision

• A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets

• E) Double DIN Trim Plate • F) Pocket

KIT COMPONENTS

1-800-221-0932

www.metraonline.com

Small Flat Blade Screwdriver • Panel Removal Tool

Phillips Screwdriver • Cutting Tool

WIRING AND ANTENNA CONNECTIONS (Sold Separately)

Harness:

• 70-1729 - Honda harness 2008-up

• 70-1730 - Honda amp interface harness 2008-up

Antenna Adapter:

• 40-HD10 - Honda antenna adapter 2005-up

TOOLS REQUIRED:

CBA

Summary of content (12 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 99-7875/99-7875T APPLICATIONS Honda Accord 2008-up (For Non-Navigation models with Dual Zone Climate controls) Honda Accord Crosstour 2010-up 99-7875/99-7875T KIT FEATURES • Painted To Match Factory Dash 99-7875=Charcoal, 99-7875T=Taupe • DIN Radio Provision with Pocket • ISO Mount Radio Provision with Pocket • Double DIN Radio Provision • Stacked ISO Mount Units Provision KIT COMPONENTS • A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets
PAGE 2
99-7875/99-7875T TABLE OF CONTENTS Dash Disassembly Honda Accord 2008-up / Crosstour 2010-up (With dual zone automatic climate controls) . . . . . . . . . . . . . . . . . . . . .1,2 Kit Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Kit Assembly - DIN Mount Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . 4 - ISO Mount Radio Provision with Pocket. . . . . . . . . . . . . . . . . . . . . . . .
PAGE 3
99-7875/99-7875T DASH DISASSEMBLY HONDA ACCORD 2008-UP/CROSSTOUR 2010-UP 1 Disconnect the negative battery terminal to prevent an accidental short circuit. A 2 Unclip and remove the trim panel from above the glove box at the right side of the factory radio. (Figure A) 3 Unclip and remove the trim panel at the left side of the factory radio. (Figure B) B 4 Remove the (2) Phillips screws from the left and right side of the of the factory radio.
PAGE 4
99-7875/99-7875T DASH DISASSEMBLY HONDA ACCORD 2008-UP/CROSSTOUR 2010-UP 9 Remove (2) Phillips screws facing up on the bottom of the factory radio. (Figure H) F 10 Unclip the factory radio assembly. Unplug and remove the radio assembly. (Figure I) 11 Remove (6) Phillips screws securing the climate controls to the factory radio assembly and remove the controls from the assembly. (Retain the screws and climate controls for reuse during kit preparation.
PAGE 5
99-7875/99-7875T KIT PREPARATION HONDA ACCORD 2008-UP/CROSSTOUR 2010-UP A 1 Snap the hazard switch/passenger air bag light assembly into the radio housing from front. (Figure A) 2 Secure the a/c vents into the radio housing using the factory hardware from rear. (Figure B) PASS AIRBENGE AG R 3 Secure the climate controls into the radio housing using the factory hardware from rear. (Figure C) B 4 Secure the trim panel onto the radio housing using the factory hardware.
PAGE 6
99-7875/99-7875T KIT ASSEMBLY DIN MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs outward. (Figure A) 2 Slide the aftermarket radio into the DIN cage until it snaps into place. (Figure B) 3 Snap the pocket into the radio housing. (Figure C) Continue to final assembly.
PAGE 7
99-7875/7875T KIT ASSEMBLY ISO MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Mount the ISO Brackets to the radio using the screws supplied with the radio. (Figure A) 2 Slide the radio into the Radio Housing until it snaps into place. (Figure B) 3 Snap the Trim Plate onto the front of the Radio Housing. (Figure C) 4 Snap the Pocket into the Radio Housing. (Figure C) B Continue to final assembly.
PAGE 8
99-7875/99-7875T KIT ASSEMBLY DOUBLE DIN/STACKED ISO MOUNT UNITS PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Cut and remove the center bar from the Radio Housing. (Figure A) 2 Snap the Double DIN brackets to the inside edge of the Radio Housing. (Figure B) 3 Slide the Double DIN or stacked ISO mount units into the bracket/radio housing assembly and secure the unit(s) to the assembly using the screws supplied with the unit(s).
PAGE 9
9-7875/99-7875T FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation.
PAGE 10
99-7875/7875T NOTES 8
PAGE 11
99-7875/99-7875T NOTES 9
PAGE 12
99-7875/7875T INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV.