® Installation instructions for part INST-7800 Acura/Honda 1990-2002 INST-7800 INSTALLATION INSTRUCTIONS • 99-7888 • 99-7889 • 99-7890 • 99-7892 • 99-7893 • 99-7894 Contents Installation Instructions - 99-7888...............................................................1.0 - 99-7889.............................................................. 2.0 - 99-7890.............................................................. 3.0 - 99-7891.............................................................. 4.
® 99-7888 Section 1 F Dash Disassembly G Acura Integra 1990-1993 Acura/Honda/Isuzu 1990-2001 1. Remove (3) screws from each side of the center console and remove the console.
® 99-7888 Dash Disassembly Acura Integra 1994-2001 1. Remove the cover cap located under the emergency brake and remove (2) screws exposed. 2. Remove (2) screws from the rear corners of the lower dash trim bezel and remove. (Figure A) 3. Remove the ashtray and (2) screws exposed. (Figure A) 4. Unsnap the ashtray housing and disconnect the cigarette lighter harness. 5. Remove the gear shifter knob and unsnap the shifter trim. 6.
® 99-7888 Dash Disassembly Acura TL 1996-1998 1. Using a small screwdriver, unclip the perimeter of the radio trim bezel. the metal housing and slide the radio out. Note, it is NOT necessary to remove the screws securing the metal housing to the bezel. 2. Disconnect the climate control and rear defroster wiring and remove the bezel. 5. Disconnect the wiring. 3. Remove (4) Phillips screws securing the factory radio/trim bezel assembly. (Figure A) 6. Cut and remove the top clips from the radio housing.
® 99-7888 Dash Disassembly Honda Accord 1990-1993 1. Remove (4) screws from the lower portion of the center console. (Figure A) 2. Remove the gear shifter knob and lift the console out. 3. Remove the ashtray and ashtray bracket. 4. Remove (2) screws from the bottom of the radio support, slide the unit out and disconnect the wiring. 5. Locate the radio housing. (Figure B) Continue to kit assembly for ALL VEHICLES, Section 1 (Figure A) (Figure B) Honda Odyssey 1995-1998 Isuzu Oasis 1996-1999 1.
® 99-7888 Kit Assembly All Vehicles 2-shaft radio provision: 1. Attach the trim plate and shaft masks to the radio housing. (Figure A1) 2. Slide the radio into the kit and secure with shaft nuts. (Figure A1) Continue to Step 5 If an equalizer will NOT be included: Snap the Equalizer Dummy Plate into the radio housing. (Figure C) 6. Insert the Radio Support into the Mounting Bracket. (Figure D) DIN radio provision: 1. . Cut and remove the shaft supports from the radio housing. 2. .
® 99-7888 Kit Assembly 8. Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra. Test the radio for proper operation. 9. Integra, Accord, Odyssey, Oasis: Snap the completed assembly into the sub-dash. (Figure G) Legend, TL, Vigor: Snap the completed assembly into the factory trim bezel. Secure the bezel to the dash with those screws previously removed. (Figure H) (Figure D) (Figure F) (Figure E) 10.
® 99-7889 Section 2 Honda Prelude 1992-1996 F 3. Pull up on the console trim bezel and remove. E 4. Using an angled screwdriver, remove (2) screws securing the gear shifter bracket to the bezel.
® 99-7889 Kit Assembly All Vehicles DIN radio provision: 2-shaft radio provision: 1. Attach the trim plate and shaft masks to the radio housing. (Figure A) 2. Slide the aftermarket radio into the kit. (Figure A) 3. Secure with shaft nuts. (Figure A) Continue to Step 5 1. Remove the metal DIN sleeve from the aftermarket radio. 2. Cut and remove the shaft supports from the radio housing. 3. Slide the sleeve into the housing and secure by bending the metal locking tabs down. (Figure B) 4.
® 99-7890 Section 3 Acura/Honda/Isuzu 1990-2001 99-7890 F G E H I KIT FEATURES • 2-shaft radio provision • DIN radio provision • Equalizer provision • Rear support provision TOOLS REQUIRED KIT COMPONENTS • Phillips screwdriver • Cutting tool • Socket wrench • A) Radio housing • B) Rear support bracket • C) Shaft supports • D) (2) Nuts • E) Radio support • F) Mounting bracket • G) Equalizer dummy plate • H) (2) Carriage bolts • I) (2) Pal nuts A B C D Table of Contents Dash Disassembly Acura –
® 99-7890 Dash Disassembly Acura CL 1997-1999 (Cont) (Figure A) (Figure C) (Figure B) (Figure D) Acura Integra 1990-1993 1. Remove (3) screws from each side of the center console and remove the console. (Figure A) 2. Remove (2) screws securing the factory radio to the sub-dash support bracket. 3. Slide the radio/pocket assembly out and disconnect the wiring. 4. Cut and remove the top clips and bottom tab from the radio housing. (Figure B) 5. Insert the radio support into the mounting bracket.
® 99-7890 Dash Disassembly Acura Integra 1994-2001 1. Remove the cover cap located under the emergency brake and remove (2) screws exposed. (Figure A) 4. Remove the gear shifter knob and unsnap the shifter trim. 5. Remove (2) screws below the radio opening and remove the upper dash trim bezel. 2. Remove (2) screws from the rear corners of the lower dash trim bezel and remove. (Figure A) 6. Remove (2) 8mm screws securing the factory radio and disconnect the wiring. 3.
® 99-7890 Dash Disassembly Acura Legend 1990 (Cont) Acura Legend 1991-1996 1. Remove (2) screws below the ashtray. Unclip the dash trim bezel. (Figure A) 2. Disconnect the cigarette lighter wiring and remove the bezel. 3. Remove (2) bolts securing the rear of the factory radio and disconnect the wiring. (Figure B) (Figure C) ¼” ¼” 1” Factory radio housing opening (Figure D) (Figure E) (Figure A) (Figure B) (Figure C) (Figure D) 5. Insert the radio support into the mounting bracket.
® 99-7890 Dash Disassembly Acura TL 1996-1998 1. Using a small screwdriver, unclip the perimeter of the radio trim bezel. 2. Disconnect the climate control and rear defroster wiring and remove the bezel. 3. Remove (4) Phillips screws securing the factory radio/trim bezel assembly. (Figure A) 4. Loosen (2) Phillips screws securing the back of the radio to the metal housing. (Figure A) (Figure B) (Figure C) (Figure D) 5. Disconnect the wiring.
® 99-7890 Dash Disassembly Acura Vigor 1992-1994 (Cont) Honda Accord 1990-1993 1. Remove (4) screws from the lower portion of the center console. (FIgure A) 2. Remove the gear shifter knob and lift the console out. Remove the ashtray and ashtray bracket. (Figure A) 3. Remove (2) screws from the bottom of the radio support, slide the unit out and disconnect the wiring. (Figure B) ¼” ¼” ¾” 1¼” 1” (Figure D) (Figure A) (Figure B) (Figure C) (Figure D) 5.
® 99-7890 Dash Disassembly Honda Accord 1994-1997 1. Remove the ashtray and (1) 3/4” #8 Phillips screw exposed. 2. Open the storage compartment and remove (2) #8 Phillips screws exposed. 3. Remove the cupholder tray and (3) #8 Phillips screws inside. (Figure A) 4. Lift the center console out and remove (2) Phillips screws exposed at the base of the dash trim bezel. Unclip the bezel and remove. (Figure A) (Figure A) (Figure B) (Figure C) (Figure D) 5.
® 99-7890 Honda Odyssey 1995-1998 (Cont) Isuzu Oasis 1996-1999 Kit Assembly All Vehicles 2-shaft radio provision: 1. Snap the shaft supports into the radio housing. (Figure A) 2. Slide the radio into the kit and secure with shaft nuts. (Figure A) Continue on the next page, Step 4 (Figure A) (Figure B) (Figure A) DIN radio provision: 1. Remove the metal DIN sleeve from the aftermarket radio. 2. Slide the sleeve into the kit and secure by bending the metal locking tabs down. 3.
® 99-7890 Kit Assembly Notes All Vehicles (Cont) 4. If an equalizer will be included: Slide the unit into the back of the radio housing and secure. If an equalizer will not be included: Snap the equalizer dummy plate into the opening. 5. Locate the factory wiring harness and connector in the dash and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra. Test the radio for proper operation. (Figure A) 6.
® 99-7891 Section 4 Dash Disassembly (Cont) F 3. Pull straight down on the lower steering column panel and remove the panel. Honda Civic 1996-1998 99-7891 4. Remove (2) Phillips screws under the climate control panel.
® 99-7891 Kit Assembly 2-shaft radio provision: 4. Locate the factory wiring harness and connector in the dash and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra. Test the radio for proper operation. 1. Snap the faceplate* and shaft supports into the radio housing. (Figure A) Continue to Step 2 5. 2-shaft radio provision (Figure E): a. Snap the completed assembly into the sub-dash. Ensure that the radio engages the radio support in the dash.
® 99-7892 Dash Disassembly Section 5 E Acura/Honda/Isuzu 1997-2001 TOOLS REQUIRED 99-7892 • Phillips screwdriver • Cutting tool • Socket wrench KIT FEATURES • 2-shaft radio provision with pocket • DIN radio provision with pocket • ISO DIN radio provision with pocket • Rear support provision KIT COMPONENTS • A) Radio housing • B) Faceplate • C) ISO DIN brackets • D) Rear support bracket • E) (2) Phillips screws A B C D Acura CL 1997-1999 Table of Contents Dash Disassembly Acura – CL 1997-1999..
® 99-7892 Dash Disassembly Acura CL 1997-1999 (Cont) Acura Integra 1990-1993 3. Cut and remove the side clips from the radio housing. (Figure B) 1. Remove (3) screws from each side of the center console and remove the console. (Figure A) 4. Secure the rear support bracket to the back of the pocket with (2) Phillips screws supplied. (Figure C) Continue to kit assembly for ALL VEHICLES, Section 5 2. Remove (2) screws securing the factory radio to the sub-dash support bracket. (Figure A) 3.
® 99-7892 Dash Disassembly Acura Integra 1994-2001 Acura Legend 1990 1. Remove the cover cap located under the emergency brake and remove (2) screws exposed. (Figure A) 1. Remove (2) screws below the ashtray. (Figure A) 2. Unclip the dash trim bezel. 3. Disconnect the cigarette lighter wiring and remove the bezel. 2. Remove (2) screws from the rear corners of the lower dash trim bezel and remove. (Figure A) 3. Remove the ashtray and (2) screws exposed.
® 99-7892 Dash Disassembly Acura Legend 1990 (Cont) Acura Legend 1991-1996 5. Cut and remove the top clips from the radio housing. (Figure B) 1. Remove (2) screws below the ashtray. Unclip the dash trim bezel. (Figure A) 6. Modify the factory radio housing by trimming the shaded portions of the housing lip. (Figure C) Continue to kit assembly for ALL VEHICLES, Section 5 2. Disconnect the cigarette lighter wiring and remove the bezel. 3.
® 99-7892 Dash Disassembly Acura TL 1996-1998 Acura Vigor 1992-1994 1. Using a small screwdriver, unclip the perimeter of the radio trim bezel. 1. Remove the access cap from the climate control cluster and (1) screw exposed. (Figure A) 2. Unclip the cluster and remove (2) screws exposed. Remove the ashtray and (2) Phillips screws exposed. (Figure A) 3. Remove the cover caps from each front corner of the center console and the screws exposed. 4.
® 99-7892 Dash Disassembly Honda Accord 1990-1993 Honda Accord 1994-1997 1. Remove (4) screws from the lower portion of the center console. (Figure A) 1. Remove the ashtray and (1) 3/4” #8 Phillips screw exposed. 2. Open the storage compartment and remove (2) #8 Phillips screws exposed. 3. Remove the cupholder tray and (3) #8 Phillips screws inside. (Figure A) 4. Lift the center console out and remove (2) Phillips screws exposed at the base of the dash trim bezel. (Figure B) 5.
® 99-7892 Dash Disassembly Kit Assembly All Vehicles Honda Odyssey 1995-1998, Isuzu Oasis 1996-1999 2-shaft radio provision with pocket: 1. Remove (2) 8mm screws under the glove box. 1. Snap the faceplate into the radio housing. (Figure A) 2. Remove (1) Phillips screw on the glove box arm and remove the box. 3. Remove (2) Phillips screws exposed in the glove box cavity. 4. Remove (2) Phillips screws below the storage box door (under the ashtray).
® 99-7892 Kit Assembly (Cont) DIN radio provision with pocket: All vehicles (CONT): 1. Remove the metal DIN sleeve from the aftermarket radio. 4. Locate the factory wiring harness and connector in the dash and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra. Test the radio for proper operation. 2. Slide the sleeve into the kit and secure by bending the metal locking tabs down. (Figure B) 3. Slide the radio into the sleeve until it clicks in.
® 99-7893 Section 6 Table of Contents Dash Disassembly (Cont) Honda CR-V / Prelude 1997-2001 remove the (4) outer screws exposed. Unclip the center console and remove. 99-7893 Dash Disassembly – Honda CR-V 1997-2001....................................... 6.0 – Honda Prelude 1997-2001................................... 6.1 • DIN radio provision with pocket • 2-shaft radio provision with pocket Kit Assembly – 2-shaft radio provision with pocket................6.1-6.
® 99-7893 Dash Disassembly Kit Assembly All Vehicles Honda Prelude 1997-2001 1. Using a panel removal tool, unclip the radio trim bezel and remove (some force may be required). (Figure A) 2. Remove (4) Phillips screws securing the factory radio/ bracket housing assembly and disconnect the wiring. 2-shaft radio provision with pocket: 1. Slide the radio into the radio housing. (Figure A) 2. Secure unit with shaft nuts. (Figure A) 3.
® 99-7893 Kit Assembly (Cont) Notes All Vehicles (CONT) 5. Install the completed assembly to the vehicle. CR-V: Snap the completed assembly into the radio trim bezel and secure the bezel to the dash using those screws previously removed. (Figure C) Prelude: (Figure C) Snap the completed assembly into the factory bracket housing and secure the housing to the sub-dash with (4) Phillips screws previously removed. (Figure D) (Figure D) 6.
® 99-7894 Section 7 Table of Contents Honda Accord 1998-2002 Dash Disassembly...........................................7.0-7.1 Kit Assembly – DIN radio provision.........................................7.1-7.2 99-7894 KIT FEATURES • DIN radio provision • Equalizer/factory-pocket provision KIT COMPONENTS • A) Radio housing • B) Brackets • C) Equalizer dummy plate A B C TOOLS REQUIRED • Phillips screwdriver • Cutting tool • Socket wrench Dash Disassembly 1.
® 99-7894 Dash Disassembly (Cont) 7. If NOT KEEPING the factory pocket: If an equalizer will be included: Slide the unit into the back of the radio housing and secure. Kit Assembly DIN radio provision: 1. Remove the metal DIN sleeve from the aftermarket radio. “A” 2. Slide the sleeve into the radio housing and secure by bending the metal locking tabs down. If an equalizer will not be included: Snap the equalizer dummy plate into the opening.
® 99-7895 Section 8 Table of Contents Dash Disassembly Honda Accord 1998-2002 Dash Disassembly........................................ 8.0 Kit Assembly 1. Unsnap the clock panel, disconnect the wiring and remove. 99-7895 – DIN radio provision with pocket................... 8.1 2. Remove (1) Phillips screw exposed in the clock cavity. (Figure A) 3. Remove (2) Phillips screws below the factory radio. Unclip the radio trim bezel and disconnect the wiring.
® 99-7895 Kit Assembly DIN radio provision with pocket: 1. Remove the metal DIN sleeve from the aftermarket radio. 2. Slide the sleeve into the radio housing and secure by bending the metal locking tabs down. 3. Slide the radio into the sleeve until it clicks in. (Figure A) 4. Locate the factory wiring harness and antenna connector in the dash. Metra recommends using the proper mating adapter from Metra. Test the radio for proper operation. (Figure A) (Figure B) 5.
® Notes
® Notes
® Notes
® Notes
® Installation instructions for part INST-7800 IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling. KNOWLEDGE IS POWER REV.
