User Manual

ManualsBrandsMetra ManualsAutomotiveMetra 99-7951 Single DIN Installation Kit for 2004-2008 Suzuki Verona/Chevrolet Aveo

INSTALLATION INSTRUCTIONS FOR PART 99-7951

Phillips Screwdriver • Flat Blade Screwdriver Or Panel Removal Tool

1-800-221-0932 www.metraonline.com

KIT FEATURES

APPLICATIONS

• DIN Head Unit Provision with pocket

• ISO DIN Head Unit Provision with pocket

A) Radio Housing • B) ISO Brackets • C) Trim Plate

KIT COMPONENTS

99-7951

CHEVROLET

Aveo 2004-2006

Aveo Hatchback-2007-2008

SUZUKI

Forenza 2004-2008

Reno 2005-2008

Verona 2004-2007

PONTIAC

G3 Hatchback-2007

TOOLS REQUIRED:

WIRING AND ANTENNA CONNECTIONS

(Sold Separately)

Harness:

• 70-8405

- GM/Suzuki/Daewoo

harness 1999-up

Antenna Adapter:

• Not required

Summary of content (12 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 99-7951 APPLICATIONS CHEVROLET Aveo 2004-2006 Aveo Hatchback-2007-2008 SUZUKI Forenza 2004-2008 Reno 2005-2008 Verona 2004-2007 PONTIAC G3 Hatchback-2007 99-7951 KIT FEATURES • DIN Head Unit Provision with pocket • ISO DIN Head Unit Provision with pocket KIT COMPONENTS A) Radio Housing • B) ISO Brackets C A B • C) Trim Plate WIRING AND ANTENNA CONNECTIONS (Sold Separately) Harness: • 70-8405 - GM/Suzuki/Daewoo harness 1999-up Antenna Adapter: • Not required TOO
PAGE 2
99-7951 TABLE OF CONTENTS • Dash Disassembly - Suzuki Verona 2004 - 2007 ---------------------------------------- 1 - Chevrolet Aveo 2004 - 2006 --------------------------------------- 2 - Chevrolet Aveo Hatchback - 2007-2008--------------------------- 2 - Pontiac G3 Hatchback - 2007 -------------------------------------- 2 - Suzuki Forenza 2004-2008 ---------------------------------------- 3 - Suzuki Reno 2005-2008 --------------------------------------------3 • Kit Assembly Chevrolet Aveo/Aveo Hatchbac
PAGE 3
99-7951 DASH DISASSEMBLY SUZUKI VERONA 2004 - 2007 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove the trim plate panel surrounding the radio. (Figure A) 3 Remove (4) Phillips screws holding radio to remove.
PAGE 4
99-7951 DASH DISASSEMBLY CHEVROLET AVEO 2004 - 2006 CHEVROLET AVEO HATCHBACK - 2007-2008 PONTIAC G3 HATCHBACK - 2007 1 Disconnect the negative battery terminal to prevent an accidental short circuit. A 2 Unclip and remove the trim panels from both sides of radio/climate controls. (Figure A) 3 Remove (4) Phillips screws from radio to remove.
PAGE 5
99-7951 DASH DISASSEMBLY SUZUKI FORENZA 2004-2008 SUZUKI RENO 2005-2008 A 1 Disconnect air selector cable on drivers side of center console behind dash above accelerator pedal. (Figure A & B) 2 Open glove box and remove (5) Phillips screws ((3) on top and (2) on bottom) then remove entire glove. B 3 Disconnect temperature selector cable on passenger side of center console behind glove box. (Figure C) 4 Unsnap and remove entire panel surrounding radio.
PAGE 6
99-7951 KIT ASSEMBLY CHEVROLET AVEO 2004 - 2006 CHEVROLET AVEO HATCHBACK - 2007-2008 PONTIAC G3 HATCHBACK - 2007 SUZUKI VERONA 2004-2007 DIN HEAD UNIT PROVISION 1 A Cut and remove front lower mounting tabs from radio housing. (Figure A) 2 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure B) 3 Slide the aftermarket head unit into the cage and secure.
PAGE 7
99-7951 KIT ASSEMBLY CHEVROLET AVEO 2004 - 2006 CHEVROLET AVEO HATCHBACK - 2007-2008 PONTIAC G3 HATCHBACK - 2007 SUZUKI VERONA 2004-2007 ISO DIN HEAD UNIT PROVISION 1 Cut and remove front lower mounting tabs from radio housing. (Figure A) 2 Mount the ISO Brackets to the head unit with the screws supplied with the unit. (Figure B) 3 Slide the head unit into the radio opening until the side clips engage. (Figure C) A B 4 Snap the Trim plate into the Radio Housing.
PAGE 8
99-7951 KIT ASSEMBLY SUZUKI FORENZA 2004-2008 SUZUKI RENO 2005-2008 DIN HEAD UNIT PROVISION WITH POCKET 1 Cut and remove rear lower mounting tabs from radio housing. (Figure A) A 2 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure B) 3 Slide the aftermarket head unit into the cage and secure.
PAGE 9
9-7951 KIT ASSEMBLY SUZUKI FORENZA 2004-2008 SUZUKI RENO 2005-2008 ISO DIN HEAD UNIT PROVISION 1 Cut and remove rear lower mounting tabs from radio housing. (Figure A) 2 Mount the ISO Brackets to the head unit with the screws supplied with the unit. (Figure B) A 3 Slide the head unit into the radio opening until the side clips engage. (Figure C) B 4 Snap the Trim plate into the Radio Housing.
PAGE 10
99-7951 FINAL ASSEMBLY FINAL ASSEMBLY A B C A) Strip wire ends back 1/2" B) Twist ends together C) Solder D) Tape D 1 2 3 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) Re-connect the negative battery terminal and test the unit for proper operation. Snap radio housing assembly into factory radio opening.
PAGE 11
99-7951 NOTES 9
PAGE 12
99-7951 INSTRUCTIONS 1-800-221-0932 REV. 07/09/09 www.metraonline.