User Manual

ManualsBrandsMetra ManualsCar & Vehicle ElectronicsToyota In-Dash Receiver Kit for 2003-06 Models

INSTALLATION INSTRUCTIONS FOR PART 99-8207

1-800-221-0932 www.metraonline.com

KIT FEATURES

• DIN Head Unit Provision with pocket

• ISO DIN Head Unit Provision with pocket

A) Radio Housing with Pocket • B) ISO Snap-in Brackets • E) ISO Trim-plate

KIT COMPONENTS

TOOLS REQUIRED:

99-8207

APPLICATIONS

Phillips Screwdriver

Toyota

Sequoia 2003-2007

Tundra 2003-2006

Socket Wrench

NOTE: Refer also to the instructions

included with the aftermarket radio.

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 99-8207 APPLICATIONS Toyota Sequoia 2003-2007 Tundra 2003-2006 99-8207 NOTE: Refer also to the instructions included with the aftermarket radio. KIT FEATURES • DIN Head Unit Provision with pocket • ISO DIN Head Unit Provision with pocket KIT COMPONENTS A) Radio Housing with Pocket • A B) ISO Snap-in Brackets • B E) ISO Trim-plate E TOOLS REQUIRED: Phillips Screwdriver 1-800-221-0932 Socket Wrench www.metraonline.
PAGE 2
99-8207 TABLE OF CONTENTS Dash Disassembly Sequoia 2003-2007............................................................................1 Tundra 2003-2006........................................................................... 2 Kit Assembly Din Head Unit Provision with pocket.............................................................. 3 ISO Din Head Unit Provision with pocket....................................................... 4 Final Assembly .....................................................
PAGE 3
99-8207 DASH DISASSEMBLY TOYOTA SEQUOIA 2003-2007 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Position vents facing upward and remove (1) Phillips screw from each A/C vent. (Figure A) 3 Unclip and remove entire radio trim panel including climate controls. (Figure B) B 4 Remove (4) 10 mm bolts to remove radio. (Figure C) C A Continue to kit assembly.
PAGE 4
99-8207 DASH DISASSEMBLY TOYOTA TUNDRA 2003-2006 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Remove the (3) climate control knobs by pulling straight outward. (Figure A) 3 Remove (3) Phillips screws from behind knobs. (Figure A) 4 Position vents facing upward and remove (1) Phillips screw from each A/C vent. (Figure B) 5 Unclip and remove entire radio trim panel including climate controls. (Figure C) 6 Remove (4) 10 mm bolts to remove radio.
PAGE 5
99-8207 KIT ASSEMBLY DIN HEAD UNIT PROVISION WITH POCKET A 1 Slide DIN cage (supplied with radio) into the radio housing from the front. (Figure A) 2 Secure DIN cage to radio housing by bending the locking tabs outward. (Figure A) B 3 Slide the radio into the DIN cage until it snaps into place. (Figure B) Continue to final assembly.
PAGE 6
99-8207 KIT ASSEMBLY ISO DIN HEAD UNIT PROVISION WITH POCKET A 1 Align the holes in the ISO brackets with the holes in the radio. Mount the brackets to the radio using screws supplied with the radio. (Figure A) 2 Slide the radio bracket assembly into the radio housing until it snaps into place. (Figure B) 3 Snap the ISO trim-plate onto the front of the assembled radio and housing. (Figure B) B Continue to final assembly. NOTE: To remove the radio unsnap and remove the ISO trim-plate.
PAGE 7
99-8207 FINAL ASSEMBLY FINAL ASSEMBLY 1 Locate the factory wiring harness in the dash and make the connection as shown. Metra recommends using the proper mating adapter and making the connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disassembly.
PAGE 8
99-8207 INSTRUCTIONS 1-800-221-0932 REV. 06/20/07 www.metraonline.