Owner's Manual

ManualsBrandsMetra ManualsAudio accessories & installation99-8220 Dash Kit

Metra. The World’s Best Kits.



INSTALLATION INSTRUCTIONS

99-8220

Attention! Let the vehicle sit with the key

out of the ignition for a few minutes before

removing the factory radio. When testing the

aftermarket equipment, ensure that all factory

equipment is connected before cycling the

key to ignition.

KIT FEATURES

• DIN radio provision with pocket

• ISO DIN radio provision with pocket

• ISO DDIN radio provision

• 99-8820 - Painted matte black

• 99-8820HG - Painted high gloss black

• 99-8820CHG -Painted high gloss charcoal

(matches 2010-up)

KIT COMPONENTS

• A) Radio housing • B) ISO DDIN trim plate • C) ISO DDIN radio brackets • D) ISO DIN trim plate • E) ISO DIN radio brackets • F) Pocket

TOOLS REQUIRED

• Panel removal tool • Phillips screwdriver

• Hook tool • 10mm socket wrench • Cutting tool

TABLE OF CONTENTS

Dash Disassembly

-With console shifter .............................................2

-With column shifter .............................................3

Kit Assembly

–DIN radio provision with pocket ........................4

–ISO DIN radio provision with pocket ..................5

–ISO DDIN radio provision .....................................6

WIRING & ANTENNA CONNECTIONS

(sold separately)

Wiring Harness: Please visit metraonline.com

for wiring harness options

Antenna Adapter: Please visit metraonline.com

for antenna adapter options

A B C

D E

Toyota Sequoia 2008-up, Tundra 2007-2013

Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle

speciﬁc applications

Summary of content (8 pages)

PAGE 1
99-8220 I N S TA L L AT I O N I N S T R U C T I O N S Toyota Sequoia 2008-up, Tundra 2007-2013 Visit MetraOnline.
PAGE 2
DASH DISASSEMBLY With console shifter 1. Unclip and remove the trim panel around the cup holders. (Figure A) 2. Remove (1) Phillips screw securing the shifter trim panel, then unclip and remove the panel. (Figure B) 3. Unclip, unplug and remove the climate control assembly. (Figure C) 4. Remove (4) 10mm screws securing the bottom of the radio. (Figure D) 5. Unclip the right side of the instrument panel trim to allow room for the radio to be removed in the following step.
PAGE 3
DASH DISASSEMBLY With column shifter 1. Remove (2) plastic Phillips screws from each side of the trim panel below the cup holder, then unclip and remove the panel. (Figure A) 2. Pull the cup-holder out, then depress the clip from each side to remove the cup-holder from the dash. (Figure B) 3. Remove (4) Phillips screws securing the cup-holder assembly to the dash, then unclip and remove the assembly. (Figure C) (Figure A) (Figure B) (Figure C) (Figure D) (Figure E) (Figure F) 4.
PAGE 4
KIT ASSEMBLY DIN radio provision with pocket 1. Remove the metal DIN sleeve from the aftermarket radio. 2. Slide the sleeve into the radio housing and secure by bending the metal locking tabs outward. (Figure A) 3. Slide the radio back into the sleeve until it snaps into place. (Figure B) 4. Snap the pocket into the radio housing. (Figure C) 5. Locate the factory wiring harness and antenna connector in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS.
PAGE 5
KIT ASSEMBLY ISO DIN radio provision with pocket 1. Remove the metal DIN sleeve and trim ring from the aftermarket radio. 2. Secure the ISO DIN radio brackets to the radio using the screws supplied with the radio. (Figure A) 3. Slide the radio into the radio housing until it snaps into place. (Figure B) 4. Snap the ISO DIN trim plate onto the front of the radio/housing assembly. (Figure C) (Figure A) (Figure B) (Figure C) (Figure D) 5. Snap the pocket into the radio housing. (Figure D) 6.
PAGE 6
KIT ASSEMBLY ISO DDIN radio provision 1. Cut and remove the center bar from the radio housing. (Figure A) 2. Snap the ISO DDIN radio brackets to the inside edge of the radio housing. (Figure B) 3. Slide the radio into the bracket/radio housing assembly and secure using screws supplied with the radio. (Figure C) 4. Snap the ISO DDIN trim plate onto the front of the radio/housing assembly. (Figure C) (Figure A) (Figure B) (Figure C) 5. Locate the factory wiring harness and antenna connector in the dash.
PAGE 7
REV.
PAGE 8
99-8220 I N S TA L L AT I O N I N S T R U C T I O N S If you are having difficulties with the installation of this product, contact our Tech Support line either by phone at 1-800-253-TECH, or email at techsupport@metra-autosound.com. Before doing so, look over the instruction booklet a second time and ensure that the installation was performed exactly as the instruction booklet is stated. Have the vehicle apart and ready to perform troubleshooting steps before contacting Metra/Axxess Tech Support.