Installation Guide

ManualsBrandsMetra ManualsAudioCar Stereo Installation Kit

INSTALLATION INSTRUCTIONS FOR PART 99-7010

1-800-221-0932 www.metraonline.com

KIT FEATURES

• DIN Head unit provision with pocket

• ISO DIN Head unit provision with pocket

• DDIN Head unit provision

• ISO Stacked Head unit provision

• Painted Silver to Match Factory

A) Radio Housing B) ISOBrackets C) ISO Trim Plate D) DDIN Brackets E) Pocket F) DDIN Trim Plate

KIT COMPONENTS

TOOLS REQUIRED:

99-7010

APPLICATIONS

Mitsubishi Eclipse

2006-2011

Phillips Screwdriver • Small Flat Blade Screwdriver

WIRING AND ANTENNA CONNECTIONS (Sold Separately)

Wir

e harness:

• MITO-01 Mitsubishi amp interface harness 2006-up

• 70-7001 Mitsubishi harness 1992-up

Antenna adapter:

• Not required

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 99-7010 APPLICATIONS Mitsubishi Eclipse 2006-2011 99-7010 KIT FEATURES • DIN Head unit provision with pocket • ISO DIN Head unit provision with pocket • DDIN Head unit provision • ISO Stacked Head unit provision • Painted Silver to Match Factory KIT COMPONENTS A) Radio Housing B) ISO Brackets C) ISO Trim Plate C A D) DDIN Brackets E) Pocket F) DDIN Trim Plate D E F WIRING AND ANTENNA CONNECTIONS (Sold Separately) Wire harness: • MITO-01 Mitsubishi amp interface
PAGE 2
99-7010 TABLE OF CONTENTS Dash Disassembly Mitsubishi Eclipse 2006-2011 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Radio Housing Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Kit Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3, 4 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 3
99-7010 DASH DISASSEMBLY MITSUBISHI ECLIPSE 2006-2011 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove the trim panel including the radio a/c vents (Figure A) 3 Remove (4) Phillips screws securing radio chassis to dash to remove. (Figure B) 4 Unclip and remove the a/c vents from the factory radio trim panel. (Figure C) 5 Unclip and remove the hazard switch from the factory radio trim panel.
PAGE 4
99-7010 KIT ASSEMBLY RADIO HOUSING ASSEMBLY A 1 Clip the a/c vents into the 99-7010 radio housing. (Figure A) 2 Clip the hazard switch into the 997010 radio housing.
PAGE 5
99-7010 KIT ASSEMBLY DIN HEAD UNIT PROVISION A 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure A) 2 Slide the aftermarket head unit into the cage and secure. (Figure B) 3 Snap the pocket into the radio housing. (Figure B) B ISO DIN HEAD UNIT PROVISION A 1 Mount the ISO Brackets to the head unit with the screws supplied with the unit. (Figure A) 2 Slide the head unit into the radio opening until the side clips engage.
PAGE 6
99-7010 KIT ASSEMBLY DOUBLE DIN HEAD UNIT PROVISION A 1 Cut the center bar rib. 2 Slide the appropriate bracket into the radio housing aligning the holes in the radio housing with the holes on the bracket. (Figure A) 3 Slide the DDIN radio unit into the DDIN bracket/radio housing assembly and secure the unit to the kit using the screws supplied with the head unit. (Figure B) 4 Snap the DDIN Trim Plate into the rado housing.
PAGE 7
99-7010 FINAL ASSEMBLY FINAL ASSEMBLY 1 Locate the factory wiring harness in the dash and make the connection as shown. Metra recomends using the proper mating adapter and making the connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disassembly.
PAGE 8
99-7010 INSTRUCTIONS 1-800-221-0932 REV. 09/01/10 www.metraonline.