Installation Guide

ManualsBrandsMetra ManualsAudioHonda Civic (Excluding LX Models) 2016-2021 Car Dash Kit

Metra. The World’s Best Kits.

INSTALLATION INSTRUCTIONS

99-7821B

Attention! Let the vehicle sit with the key

out of the ignition for a few minutes before

removing the factory radio. When testing the

aftermarket equipment, ensure that all factory

equipment is connected before cycling the

key to ignition.

KIT FEATURES

KIT COMPONENTS

• A) Radio trim panel • B) Radio brackets • C) Pocket • D) (4) #8 x 3/8” Phillips screws • E) (8) Plastic panel clips

• F) Axxess wiring harness and interface (not shown) • G) Antenna adapter (not shown)

TOOLS REQUIRED

• Panel removal tool • Phillips screwdriver

TABLE OF CONTENTS

Dash Disassembly ..................................................2

Kit Preparation .......................................................3

Kit Assembly

–ISO DIN radio provision with pocket ..................4

–ISO DDIN radio provision .....................................4

Axxess Interface Installation ............................5-14

Final Assembly ......................................................15

WIRING & ANTENNA CONNECTIONS

Wiring Harness: Included in kit

Antenna Adapter: Included in kit

A B C D E

Honda Civic (Excluding LX models) 2016-2021

Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle

speciﬁc applications. Note: Additional parts required to retain factory ampliﬁer.

• ISO DIN radio provision with pocket

• ISO DDIN radio provision

• Painted matte black

• Touchscreen display for climate and

personalization features

• Retains the factory backup camera

and LaneWatch camera

• Retains audio controls on the steering wheel

• Provides NAV outputs (parking brake,

reverse, speed sense)

• Additional purchase of AXSP-HN is required

to retain factory ampliﬁer. Identiﬁable

when equipped with factory sub-woofer

or center channel speakers.

Summary of content (16 pages)

PAGE 1
99-7821B I N S TA L L AT I O N I N S T R U C T I O N S Honda Civic (Excluding LX models) 2016-2021 Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle specific applications. Note: Additional parts required to retain factory amplifier.
PAGE 2
DASH DISASSEMBLY 3. Remove (2) Philips screws securing the radio and then remove. (Figure C) 1. Unsnap and remove the side trim panels from the center console. (Figure A) 2. Unsnap and remove the climate control panel. (Figure B) 4. Remove the (2) screws securing the factory passenger airbag indicator and remove it from the factory climate controls. (Figure D) Continue to Kit Preparation (Figure A) (Figure C) (Figure D) (Figure B) 2 386.257.1187 | MetraOnline.
PAGE 3
KIT PREPARATION 1. Attach the supplied (6) plastic clips to the radio trim panel. (Figure A) 2. Attach the airbag indicator to the radio trim panel using the factory screws. (Figure B) 3. Attach the supplied (2) plastic clips to the radio brackets. (Figure C) Continue to Kit Assembly (Figure A) (Figure B) (Figure C) REV.
PAGE 4
KIT ASSEMBLY ISO DIN radio provision with pocket ISO DDIN radio provision 1. Attach the pocket to the radio brackets using the (4) Phillips screws provided. (Figure A) 1. Attach the radio brackets to the radio using the hardware provided with the radio. (Figure A) 2. Slide the radio into the assembly, and then secure it using the screws supplied with the radio. (Figure B) Continue Axxess Interface Installation Continue Axxess Interface Installation (Figure A) (Figure A) (Figure B) 4 386.257.
PAGE 5
AXXESS INTERFACE INSTALLATION INTERFACE FEATURES • Provides accessory power (12-volt 10-amp) • Provides 12-volt illumination output • Retains R.A.P.
PAGE 6
CONNECTIONS For models without a factory amp From the LD-HONTOUCH harness (loose wires for aftermarket radio) For models with a factory amp (will require the AXSP-HN) (sold separately) From the LD-HONTOUCH harness (loose wires for the aftermarket radio) • • • • • • Connect the Black wire to the ground wire. Connect the Yellow wire to the battery wire. Connect the Red wire to the accessory wire. Connect the Orange/White wire to the illumination wire.
PAGE 7
CONNECTIONS 3.5mm jack steering wheel control retention: The 3.5mm jack is to be used to retain audio controls on the steering wheel control. • For the radios listed below: Connect the included female 3.5mm connector with stripped leads, to the male 3.5mm SWC jack from the car side harness. Any remaining wires tape off and disregard: • Eclipse: Connect the steering wheel control wire, normally Brown, to the Brown/White wire of the connector.
PAGE 8
ANTENNA CONNECTIONS The antenna connection is only available at the factory tuner behind the passenger rear side trim panel. (Figure A) Connection Route the antenna extension from the radio location to the tuner location. Plug in the antenna cable and connect the Blue wire to your radio’s Amp turn on output. Disconnect the cable from the factory tuner and connect the antenna extension cable. Proper access to the tuner will require rear seat and side trim panel removal. AXSP-HN connections.
PAGE 9
INSTALLATION AND PROGRAMMING It is highly advisable to read the following steps beforehand, to ensure a clear understanding of what is to be expected. A C With the vehicle completely off: From the LD-HONTOUCH 1. Connect the 16-pin harness into port “B” in the touchscreen display 2. Connect the 22-pin connector that has the “Touchscreen Label on it” into port “A” of the Touchscreen Display. 3.
PAGE 10
TOUCHSCREEN DISPLAY OPERATION Climate Control screen Climate Control screen • This is the climate control screen, which will be displayed on the touchscreen display. This is also considered the main menu. The climate controls will function in the same manner that they did with the factory climate controls. • The upper left tab with (3) arrows will access the Heated/Cooled seats, if equipped. • Factory camera modes are available and view modes can be changed while in reverse.
PAGE 11
TOUCHSCREEN DISPLAY OPERATION (CONT.) Configuration Settings • Display • Backlight - For controlling the color of the buttons and back-light intensity.
PAGE 12
STEERING WHEEL CONTROL SETTINGS Remap Buttons Dual Assign • • The interface has the ability to change the button assignment for the steering wheel control audio buttons, except Volume-Up and Volume-Down. Follow the prompts on the touchscreen display to remap the steering wheel control audio button(s) to your liking. Note: The aftermarket radio may not have all of these commands.
PAGE 13
STEERING WHEEL CONTROL SETTINGS (CONT.) Select Radio * Note: If the interface shows an Alpine radio, and you do not have an Alpine radio, that means the interface does not detect a radio connected it, i.e., an open connection. Verify that the 3.5mm jack is connected to the correct steering wheel jack/wire in the radio. ** Note: The AX-SWC-PARROT is required (sold separately). Also, the Parrot radio must be updated to rev. 2.1.4 or higher through www.parrot.com.
PAGE 14
TROUBLESHOOTING Resetting the interface Option # 1 1. With everything connected and the car running. 2. Hold the bottom (2) buttons for 3 seconds, then release. (Figure A) (The screen will turn black and then put you in the vehicle selection screen) 3. Select your vehicle and wait till the “SWC Configured “ appears on the screen. 4. Turn ignition off and start vehicle, then test your interface. Option #2 (Figure A) 1.
PAGE 15
FINAL ASSEMBLY 1. Secure the radio into the dash and reassemble the dash in reverse order of disassembly using the new radio trim panel. REV.
PAGE 16
99-7821B I N S TA L L AT I O N I N S T R U C T I O N S Having difficulties? We’re here to help. Contact our Tech Support line at: 386-257-1187 Or via email at: techsupport@metra-autosound.com Tech Support Hours (Eastern Standard Time) Monday - Friday: 9:00 AM - 7:00 PM Saturday: 10:00 AM - 7:00 PM Sunday: 10:00 AM - 4:00 PM ® KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.