Instructions

ManualsBrandsMetra ManualsAudioMetra Honda Civic 2013-2015 Dash Kit

METRA. The World’s best kits.

metraonline.com

REV. 11/14/2017 INST99-7882B

CAUTION!

Metra recommends disconnecting the negative bat

tery terminal before beginning any installation, unless the vehicle

manufacturer recommends against so. Please check with your local

Dealership for more information. All accessories, switches, climate

controls panels, and especially air bag indicator lights must be con

nected before reconnecting the battery or cycling the ignition. Also,

do not remove the factory radio with the key in the on position, or the

vehicle running. It would be best to remove the key from the ignition

and then wait a few seconds before removing the factory radio.

U.S. PATENT # D791,118

Installation instructions for part 99-7882B

U.S. PATENT # D728,554

• ISO DIN radio provision with pocket

Note: This kit will not retain the i-MID display

• A) Radio trim panel • B) Radio brackets • C) Pocket • D) (3) metal panel clips • E) (3) plastic panel clips

• F) (4) #8 x 3/8” Phillips truss-head screws • G) (13) #8 x 3/8” Phillips pan-head screws

• H) (3) #4 x 3/8” Phillips truss-head screws • I) (2) #8 x 1/2” Phillips pan-head screws

KIT FEATURES

KIT COMPONENTS

WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness: • Please visit metraonline.com for options

Antenna Adapter: • 40-HD11

• Panel removal tool • Phillips screwdriver • 8mm socket wrench

TOOLS REQUIRED

Honda Civic 2013-2015

99-7882B

A B C D E

Dash Disassembly ..................................................2

Kit Preparation ........................................................ 3

Kit Assembly

– ISO DIN radio provision with pocket ...................... 3

Table of Contents

Summary of content (8 pages)

PAGE 1
D728,554 U.S. PATENT # D791,118 Installation instructions for part 99-7882B Table of Contents Honda Civic 2013-2015 99-7882B Dash Disassembly...................................................2 Kit Preparation.........................................................3 Kit Assembly KIT FEATURES • ISO DIN radio provision with pocket –. ISO DIN radio provision with pocket.......................
PAGE 2
® 99-7882B Dash Disassembly 1. Open the pocket door below the radio, remove (2) Phillips screws exposed, and then remove the pocket. (Figure A) (Figure D) 2. Remove (2) Phillips screws from the bottom edge of the radio. (Figure B) 3. Remove (2) 8mm screws facing up from inside the pocket cavity. (Figure C) (Figure A) 4. Unsnap and remove the climate/ radio panel assembly. (Figure D) Step 5 c Step 5 b 5. Remove the components from the climate/radio panel to be reused in kit assembly. (Figure E) a.
PAGE 3
® 99-7882B Kit Preparation Kit Assembly ISO DIN radio provision with pocket 1. Secure the factory components removed in dash disassembly to the radio panel. Except for the (3) screws to secure the lower trim panel, either the factory screws or the (9) #8 x 3/8” Phillips pan-head screws supplied with the kit may be used. For the lower trim panel use the (3) #4 x 3/8” Phillips truss-head screws supplied with the kit to secure it to the panel. (Figure A) 1.
PAGE 4
Installation instructions for part 99-7882B IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling. ® KNOWLEDGE IS POWER REV.
PAGE 5
® U.S. PATENT # D728,554 Instrucciones de instalación para la pieza 99-7882B Indice Honda Civic 2013-2015 99-7882B Desmontaje del tablero...........................................2 Preparación del kit..................................................3 CARACTERÍSTICAS DEL KIT • Provisión de radio ISO DIN con cavidad Ensamble del kit –. Provisión de radio ISO DIN con cavidad.................
PAGE 6
® 99-7882B Desmontaje del tablero 1. Abra la puerta de la cavidad debajo del radio, retire los (2) tornillos Phillips expuestos, y después retire la cavidad. (Figura A) (Figura D) 2. Quite los (2) tornillos Phillips del borde inferior del radio. (Figura B) 3. Quite los (2) tornillos de 8mm orientados hacia arriba de dentro de la cavidad. (Figura C) (Figura A) 4. Suelte a presión y quite el ensamble del panel de clima/radio. (Figura D) Paso 5 c Paso 5 b 5.
PAGE 7
® 99-7882B Preparación del kit Ensamble del kit 1. Atornille los componentes de fábrica que quitó en el desmontaje del tablero al panel del radio. Exceptuando los (3) tornillos que aseguran el panel de la moldura inferior, se pueden usar los tornillos de fábrica o los (9) tornillos Phillips de cabeza troncocónica #8 x 3/8” suministrados con el kit. Para el panel de la moldura inferior use los (3) tornillos Phillips de cabeza segmentada #4 x 3/8” suministrados con el kit para atornillarlo al panel.
PAGE 8
® Instrucciones de instalación para la pieza 99-7882B IMPORTANTE Si tiene dificultades con la instalación de este producto, llame a nuestra línea de soporte técnico al 1-800-253-TECH. Antes de hacerlo, revise las instrucciones por segunda vez y asegúrese de que la instalación se haya realizado exactamente como se indica en las instrucciones. Por favor tenga el vehículo desarmado y listo para ejecutar los pasos de resolución de problemas antes de llamar.