Instructions

ManualsBrandsMetra ManualsAudioMetra Tan Lexus RX300 1999-2003 TurboTouch Kit

Metra. The World’s Best Kits.



INSTALLATION INSTRUCTIONS

99-8164

Attention! Let the vehicle sit with the key

out of the ignition for a few minutes before

removing the factory radio. When testing the

aftermarket equipment, ensure that all factory

equipment is connected before cycling the

key to ignition.

• ISO DDIN radio provision

• ISO DIN radio provision with pocket

• Custom texture and painted tan or gray to match the factory appearance

• Touchscreen for retention of climate control functions

• Factory ampliﬁer not retained with this product - an ampliﬁer bypass

harness is included

• 99-8164T — Tan w/black trim, 99-8164G — Gray w/black trim

KIT FEATURES

KIT COMPONENTS

• A) Radio trim panel • B) Radio brackets • C) Pocket • D) Panel clips (3) • E) #8 x 3/8” Pan-head Philips screws (8)

• F) Wiring and interfacing (not shown)

TOOLS REQUIRED

• Panel removal tool • Phillips screwdriver

• 10mm Socket wrench

TABLE OF CONTENTS

Dash Disassembly ..................................................2

Kit Preparation .......................................................3

Kit Assembly ..........................................................4

Axxess Interface Installation .............................5-11

Final Assembly .......................................................9

WIRING & ANTENNA CONNECTIONS

Wiring Harness: Included with kit

Antenna Adapter:

Not needed

Lexus RX300 1999-2003

A B C D

Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle

speciﬁc applications

Summary of content (12 pages)

PAGE 1
99-8164 I N S TA L L AT I O N I N S T R U C T I O N S Lexus RX300 1999-2003 Visit MetraOnline.
PAGE 2
DASH DISASSEMBLY 1. Unsnap and remove the shifter trim. (Figure A) 3. Depress side tabs to remove the factory hazard button and passenger airbag light from the factory radio assembly. (Figure C) 2. Remove (4) 10mm bolts and remove the radio assembly. (Figure B) 4. Depress all four side tabs to remove the factory vents from the factory radio assembly. (Figure D) Continue to Kit Preparation 2 (Figure A) (Figure C) (Figure B) (Figure D) 386.257.1187 | MetraOnline.
PAGE 3
KIT PREPARATION 1. Attach the (3) supplied panel clips to the radio trim panel. (Figure A) 2. Snap the passenger airbag light and hazard button into the radio trim panel from the back. (Figure B) 3. Attach the factory vents to the radio trim panel (Figure C) Continue to Kit Assembly (Figure B) (Figure C) (Figure A) REV.
PAGE 4
KIT ASSEMBLY ISO-DIN radio provision with pocket ISO-DDIN radio provision 1. Secure the pocket to the radio brackets using the (4) #8 x 3/8” Phillips screws supplied. (Figure A) 1. Secure the radio brackets to the radio using screws supplied with the radio. (Figure A) 2. Attach the radio bracket/pocket assembly to the radio using screws supplied with the radio. (Figure B) 2. Attach the completed assembly to the radio trim panel using the supplied (4) #8 x 3/8” Phillips screws. (Figure B) 3.
PAGE 5
AXXESS INTERFACE INSTALLATION INTERFACE FEATURES • Provides accessory power (12-volt 10-amp) • Retains R.A.P. (retained accessory power) • Touchscreen for retention of climate control functions • Micro “B” USB updatable TABLE OF CONTENTS Connections................................................................................................................................ 6-8 Installation.....................................................................................................................
PAGE 6
CONNECTIONS From the LD-8164 harness to the aftermarket radio: The Yellow/Black ‘Bean BUS’ wire must be connected properly for this interface to function: • Connect the Black wire to the ground wire. Locate the 13 pin connector in the vehicle. • Connect the Yellow wire to the battery wire. The following connections will have to be made. • Connect Red wire to the accessory wire.
PAGE 7
CONNECTIONS Use the LD-8164-NAV harness for vehicles with Factory Navigation (CONT.) The Yellow/Black ‘Bean BUS’ wire must be connected properly for this interface to function: Locate the gray 14 pin connector in the vehicle. From the LD-8164-NAV harness to the aftermarket radio: The following connections will have to be made. • Connect Black to the ground wire • Connect the Yellow/Black wire labelled ‘Bean BUS’ to the Yellow/Black wire on the factory connector.
PAGE 8
CONNECTIONS (CONT.) 4-pin harness with yellow RCA jacks: Amplifier bypass: • Backup camera harness (4-pin harness with yellow RCA jacks): Use the included amplifier bypass to connect to the speakers. Take note that there are multiple speakers with varying impedance. An external amplifier and crossovers are recommended. • There are two different methods for connecting an aftermarket camera.
PAGE 9
INSTALLING THE INTERFACE It is highly advisable to read the following steps beforehand, to ensure a clear understanding of what is to be expected. The following steps must be done in the order that they are numbered. PROGRAMMING • Open the drivers door and keep open during the process. • Cycle the ignition to on. • Connect the harnessing to the vehicle. With the vehicle completely off: • Wait until the radio powers on and the touchscreen displays “SWC configured”.
PAGE 10
TOUCHSCREEN DISPLAY OPERATION HVAC control screen Configuration Settings screen • This is the HVAC control screen which will be displayed on the touchscreen display. This is considered the main screen. Backlight • The upper right tab with the gear icon will take you to the Configuration Settings screen. • The climate controls will function in the same manner that they did with the factory climate controls. • For controlling the color of the buttons and back-light intensity.
PAGE 11
TOUCHSCREEN DISPLAY OPERATION (CONT.) Touchscreen calibration: • Press and hold the upper two soft buttons on either side of the touchscreen for 10 seconds. • A screen will pop up asking for you to press the target in the screen. • After pressing the target with your finger, the calibration process will be complete, and the screen will disappear. REV.
PAGE 12
99-8164 I N S TA L L AT I O N I N S T R U C T I O N S Having difficulties? We’re here to help. Contact our Tech Support line at: 386-257-1187 Or via email at: techsupport@metra-autosound.com Tech Support Hours (Eastern Standard Time) Monday - Friday: 9:00 AM - 7:00 PM Saturday: 10:00 AM - 7:00 PM Sunday: 10:00 AM - 4:00 PM ® KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.