Installation Guide

ManualsBrandsMetra ManualsAudioMetra Toyota Car Dash Kit

CAUTION!

All accessories, switches, climate

controls panels, and especially air bag indicator

lights must be connected before cycling the

ignition. Also, do not remove the factory radio

with the key in the on position, or while the

vehicle is running.

Metra. The World’s Best Kits.



INSTALLATION INSTRUCTIONS

99-8244HG

KIT FEATURES

• ISO DIN radio provision with pocket

• Painted high gloss black

KIT COMPONENTS

• A) Radio housing • B) Radio brackets • C) Pocket • D) (1) Passenger Air Bag Light board cover • E) (2) Panel clip mounts

• F) (4) #8 x 3/8” pan-head Phillips screws • G) (7) #4 x 3/8” pan-head Phillips screws • H) (1) Air-Bag sticker (not shown)

TOOLS REQUIRED

• Panel removal tool • Phillips screwdriver

• Socket wrench

TABLE OF CONTENTS

Dash Disassembly .............................................. 2-5

Kit Preparation .......................................................6

Kit Assembly

–ISO DIN radio provision with pocket ..................7

WIRING & ANTENNA CONNECTIONS

(sold separately)

Wiring Harness: 70-1761 • TYTO-02 (For models

with a JBL amp)

Antenna Adapter: 40-LX11

Toyota Avalon 2013-up*

*Visit MetraOnline.com for up-to-date vehicle speciﬁc applications.

A B C

Summary of content (16 pages)

PAGE 1
99-8244HG I N S TA L L AT I O N I N S T R U C T I O N S Toyota Avalon 2013-up* TABLE OF CONTENTS Dash Disassembly............................................... 2-5 Kit Preparation........................................................6 Kit Assembly –ISO DIN radio provision with pocket...................7 *Visit MetraOnline.com for up-to-date vehicle specific applications.
PAGE 2
DASH DISASSEMBLY 1. Unclip and remove the a/c vent panel above the factory radio and surrounding the instrument cluster. (Figure A) 3. Remove (4) 10mm bolts (2 on top and 2 on bottom) securing the factory radio then unclip and remove. (Figure C,D) Tip: Start at the passenger side of the panel. Upper bolts Continued on the next page 2. Unclip and remove the panel below the factory radio. (Figure B) (Figure A) (Figure C) Lower bolts (Figure B) 2 (Figure D) 1.800.221.0932 | MetraOnline.
PAGE 3
DASH DISASSEMBLY (CONT.) 4. Remove (4) small Phillips screws securing the panel clip and screw mount to the factory radio. Retain for kit assembly. (Figure E) 5. Remove (9) small Phillips screws securing the radio chassis to the main panel of the factory radio. (Figure F) Continued on the next page (Figure E) (Figure F) REV.
PAGE 4
DASH DISASSEMBLY (CONT.) 6. Remove (2) remaining Phillips screws securing the Passenger Air Bag Light board to the main factory radio panel. Retain board for kit assembly. (Figure G) 7. Remove the remaining (2) yellow panel clips and retain for kit assembly. (Figure H) Continued on the next page (Figure G) (Figure H) 4 1.800.221.0932 | MetraOnline.
PAGE 5
DASH DISASSEMBLY (CONT.) 8. Remove (2) Phillips screws and then unclip the chrome trim around the outside of the radio/climate control assembly. Retain for kit assembly. (Figure I) 9. Remove the radio brackets and the climate control from the factory radio. Retain climate control for kit assembly. Continue to Kit Preparation (Figure I) REV.
PAGE 6
KIT PREPARATION 1. Attach the Passenger Air Bag Light board to the radio housing with the factory hardware. (Figure A) 2. Attach the Passenger Air Bag Light board cover to the radio housing panel over the Passenger Air Bag Light board using (3) of the #4 x 3/8” Phillips screws supplied. (Figure A) 3. Apply the supplied Air Bag Sticker to the face of the radio housing. (Figure A) 4. Attach the panel clip and screw mount to the radio housing using the factory hardware.
PAGE 7
KIT ASSEMBLY ISO DIN radio provision with pocket 1. Secure the pocket to the radio brackets with the (4) #8 x 3/8” Phillips screws supplied. (Figure A) 2. Slide the radio onto radio brackets and secure with the screws supplied with the radio. (Figure B) 3. Secure the radio/pocket/bracket assembly to the radio housing/climate control assembly with the factory hardware. 4. Locate the factory wiring harness and antenna connector in the dash and complete all necessary connections to the radio.
PAGE 8
99-8244HG I N S TA L L AT I O N I N S T R U C T I O N S IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling.
PAGE 9
9-8244HG I N S T R U C C I O N E S D E I N S TA L AC I Ó N Toyota Avalon 2013 y mas* * Visite MetraOnline.com para aplicaciones específicas de vehículos actualizadas.
PAGE 10
DESMONTAJE DEL TABLERO 3. Quite los (4) pernos de 10mm (2 arriba y 2 abajo) que sujetan el radio de fábrica, luego desenganche y quite. (Figura C,D) 1. Desenganche y quite el panel de la rejilla de aire acondicionado de arriba del radio de fábrica y que rodea el tablero de instrumentos. (Figura A) Pernos superiores Continua en la siguiente pagina Sugerencia: Empiece en el lado del pasajero del panel. 2. Desenganche y quite el panel de abajo del radio de fábrica.
PAGE 11
DESMONTAJE DEL TABLERO (CONT.) 4. Quite los (4) tornillos Phillips que sujetan el gancho del panel y atornille el soporte al radio de fábrica. Retenga para el ensamble del kit. (Figura E) 5. Quite los (9) tornillos Phillips pequeños que sujetan el chasís del radio al panel principal del radio de fábrica. (Figura F) Continua en la siguiente pagina (Figura E) (Figura F) REV.
PAGE 12
DESMONTAJE DEL TABLERO (CONT.) 6. Quite los (2) tornillos Phillips restantes que sujetan el tablero de la luz de la bolsa de aire del pasajero al panel de radio de fábrica principal. Retenga el tablero para el ensamble del kit. (Figura G) 7. Quite los (2) ganchos del panel amarillo restantes y reténgalos para ensamblar el kit. (Figura H) Continua en la siguiente pagina (Figura G) (Figura H) 4 1.800.221.0932 | MetraOnline.
PAGE 13
DESMONTAJE DEL TABLERO (CONT.) 8. Quite los (2) tornillos Phillips y luego desenganche la moldura cromada de alrededor del exterior del ensamble del control del radio/clima. Retenga para el ensamble del kit. (Figura I) 9. Quite los soportes del radio y el control de clima del radio de fábrica. Retenga el control de clima para el ensamble del kit. Continúe con la Preparación del Kit (Figura I) REV.
PAGE 14
PREPARACIÓN DEL KIT 1. Coloque el tablero de la luz de la bolsa de aire del pasajero en la carcasa del radio usando la tornillería de fábrica. (Figura A) 2. Coloque la cubierta del tablero de la luz de la bolsa de aire del pasajero en el panel de la carcasa del radio sobre el tablero de la luz de la bolsa de aire del pasajero con (3) de los tornillo Phillips #4 x 3/8” suministrados. (Figura A) 3. Aplique la calcomanía de bolsa de aire suministrada en la cara de la carcasa del radio. (Figura A) 4.
PAGE 15
KIT ASSEMBLY Provisión de radio ISO DIN con cavidad 1. Sujete la cavidad en los soportes del radio con los (4) tornillos Phillips #8 de 3/8” suministrados. (Figura A) 2. Deslice el radio en los soportes del radio y sujételo con los tornillos suministrados con el radio. (Figura B) 3. Sujete el conjunto del radio/cavidad/ soporte al conjunto de la carcasa del radio/control de clima utilizando la tornillería de fábrica. 4.
PAGE 16
99-8244HG I N S T R U C C I O N E S D E I N S TA L AC I Ó N IMPORTANTE Si tiene dificultades con la instalación de este producto, llame a nuestra línea de soporte técnico al 1-800-253-TECH. Antes de hacerlo, revise las instrucciones por segunda vez y asegúrese de que la instalación se haya realizado exactamente como se indica en las instrucciones. Por favor tenga el vehículo desarmado y listo para ejecutar los pasos de resolución de problemas antes de llamar.