Owner's Manual

MetraHomeTheater.com
CAUTION!
866-839-9187
460 Walker Street
lnstallation lnstructions
Holly Hill, FL 32117-2653
C>2019 Metra Electronics Corporation
Designed and Manufactured to
Metra Home Theater Ciroup Specifications
MADE IN CHINA
Do not hang Large size
speakers from the brackets.
Avoid the risk of instability
of the center of gravity !
AS-SPKR-19
IMPORTANT
Please read the instruction sheet prior to installation. This speaker
mount was designed solely for the mounting of small speakers weighing
less than lOlbs. We are not responsible for damage that may
1/4"-20x7/8" Machine Screw (1)
M5x20mm Machine Screw (1)
8#-32x5/8" Machine Screw (1)
1/4"-20x1/2" Machine Screw (2)
M5x1 /8" Plastic Washor (1)
8#-32 Round Key Hole Nut (1)
ST4.2x19 SolfTapplng Screw (1)
ST5.5x19 Self Tapping Screw (2)
ST5.5x45 Self Tapping Screw (2)
occur if speakers weighing more than 10lbs. are used.
NOTE: The user will have to determine which type of configuration
will work best with the hardware that was purchased. lf the
included hardware do_es not fit the application, the appropriate
hardware will have to be purchased.
4> 8x40 Alligator Plastic Anchor (2)
M4x8mm Flat Head Machine Screw (1)
4mmAllen key(1)
05 Plastic Washor (1)
MSx 1/8"
Plastic Washer
Figure 1
Figure 2
8#-32 Round Key
Hole Nut
M4 x 8mm Flat Head
Machine Screw
Figure 4
8#-32x5/8"
Machine Screw
Single Hole Mounting
1. Most satellite speaken; will require the use of the M5 x 20mm machine
screw used in combination with the M5 x 1 /8" plastic washer. The plastic
washer is used as a spacer between the threaded insert and the post (Figure 1 ).
NOTE: lt is critical the M5 plastic washer is used correctly.
2. Once the proper configuration is determined, secure the post to the speaker.
~i~· -~ ~,~-~
-~Screw
~ ST4.2x19 Self
~ TappingScrew
3. Some speaken; use the smaller M4 x 8mm hardware,
which is inserted into the off-center hole on the
mounting post (Figure 2).
4. Check the size of the hole and make sure the 8#-32x5/8" machine
screw, the ST4.2x 19 Self Tapping Screw , the 1/4"-20x7/8 " machine
screw, or the M5 x 20mm machine screw fits inside (Figure 3).
5. When the correct size is determined, place the screw through
the speaker post and attach to the rear of the speaker enclosure.
NOTE: lf the screw does not tighten properly, use the M5 x 1 /8"
plastic washer to tighten it up.
NOTE: After finishing the post installtttien;-insernhe D5 plastic
washer into the post. ( The D5 plastic washer is not used
when the speaker requires the use of the M6x20mm
machine screw. )
Key Hole Mounting
7. lfyour speaker has a factory key hole design, you will use the
8# - 32x5/8" machine screws in combination with the key hole nut .
8. Loosely pre-assemble the mounting post with the 8#-32x5/8"
machine screw and key hole nut (Figure 4).
NOTE: Be sure the key hole nut is installed with the knurled (rough) edge
toward the post.
9. Engage the key hole nut into the key hole slot as shown.
10. Put tension on the assembly by gently pulling back on the speaker mount post
while tightening the 8#-32x5/B" machine screw (Figure 4).
11 . The key hole nut will engage on the housing in the key hole slot.
12. lf the post does not tighten securely against the housing , it will be necessary to
use the M5 x 1 /8• plastic washer as a spacer under the head of the 8#-32 x 5/8"
machine screw (Figure 4).
NOTE: After finiship,g the post installation, insert the D5 plastic washer into the post.
~/4 - Ho1e Mounting
1 3. Find the best mounting configuration that matches your speaker enclosure. Four-hole speaker mount
patterns can be accomodated by positioning the speaker plate diagonally (Figure 5).
14. Using the 1/4"-20 x 1/2" machine screws, install the speaker plate and secure the speaker
enclosure (Figure 5).
2-Hole Orientation
4-Hole Orientation
Figure 5