Installation Instructions

ManualsBrandsMetra ManualsCar HarnessMetra Into Car Harness

AX-HYKIA4-SWC

INSTALLATION INSTRUCTIONS

Attention! Let the vehicle sit with the key

out of the ignition for a few minutes before

removing the factory radio. When testing the

aftermarket equipment, ensure that all factory

equipment is connected before cycling the

key to ignition.

INTERFACE FEATURES

INTERFACE COMPONENTS

TOOLS REQUIRED

• Crimping tool and connectors, or solder gun,

solder, and heat shrink • Tape • Wire cutter

• Zip ties • Small ﬂat-blade screwdriver

TABLE OF CONTENTS

Connections ............................................................2

Installation .............................................................3

Programming .........................................................3

Audio Level Adjustment ........................................3

Steering Wheel Control Settings

- L.E.D. feedback ....................................................4

- Changing radio type ...........................................4

- Remapping the steering wheel control buttons 5-6

- Dual assignment instructions (long button press) .6-7

Troubleshooting .....................................................7

Hyundai/Kia Data Interface with SWC 2010-2013

APPLICATIONS

• Provides NAV outputs (park

brake, reverse, speed sense)

• Retains audio controls on the

steering wheel

• Designed for ampliﬁed models

• Retains the factory AUX-IN jack

• Retains the factory backup

camera

• Retains balance

• Micro-B USB updatable

Hyundai

Tucson † 2010-2013

Kia

Forte ‡ 2010-2013

Sorento † 2011-2013

• AX-HYKIA4-SWC interface • AX-HYKIA4-SWC harness

• AX-HYKIA-SPDIF interface • 16-pin harness with stripped leads

• Female 3.5mm connector with stripped leads

Visit AxxessInterfaces.com for more detailed information about the product and up-to-date

vehicle speciﬁc applications

† With NAV

‡ With auto climate control or NAV

Summary of content (8 pages)

PAGE 1
AX-HYKIA4-SWC I N S TA L L AT I O N I N S T R U C T I O N S Hyundai/Kia Data Interface with SWC 2010-2013 Visit AxxessInterfaces.
PAGE 2
CONNECTIONS From the 16-pin harness with stripped leads to the aftermarket radio: • Connect the Red wire to the accessory wire. • Connect the Blue/White wire to the amp turn-on wire. • Connect the Gray wire to the right front positive speaker output. • Connect the Gray/Black wire to the right front negative speaker output. • Connect the White wire to the left front positive speaker output. • Connect the White/Black wire to the left front negative speaker output.
PAGE 3
INSTALLATION With the key in the off position: 1. Connect the 16-pin harness with stripped leads, and the AX-HYKIA4-SWC harness, to the AXHYKIA4-SWC interface. 2. Connect the AX-HYKIA-SPDIF interface to the 14-pin connector from the HYKIA4-SWC harness. PROGRAMMING (CONT.) 5. After a couple seconds the L.E.D. will turn on solid Red while the interface auto detects the vehicle. The radio will shut off at this point. This process should take 5 to 30 seconds. 6.
PAGE 4
STEERING WHEEL CONTROL SETTINGS L.E.D. feedback The (18) Red L.E.D. flashes represent the radio the AX-HYKIA4-SWC interface believes it’s connected to. Each flash represents a different radio Manufacturer. For example, if you are installing a JVC radio, the AX-HYKIA4-SWC interface will flash Red (5) times, and then stop. Following is a legend that dictates which radio Manufacturer corresponds to which flash. L.E.D.
PAGE 5
STEERING WHEEL CONTROL SETTINGS Radio legend (CONT.) Remapping the steering wheel control buttons Radio # Radio Radio # Radio 1 2 3 4 5 6 7 8 9 Eclipse (type 1) Kenwood Clarion (type 1) Sony / Dual JVC Pioneer / Jensen Alpine Visteon Valor 10 11 12 13 14 15 16 17 18 Clarion (type 2) Metra OE Eclipse (type 2) LG Parrot XITE Philips TBA JBL Once the AX-HYKIA4-SWC interface has been programmed, the button assignment for the steering wheel controls may be reassigned if so desired.
PAGE 6
STEERING WHEEL CONTROL SETTINGS Button function legend (CONT.) Dual assignment instructions (long button press) Function # Function Function # Function 1 2 3 4 5 6 7 8 9 Volume-Up Volume-Down Seek-Up/Next Seek-Down/Prev Source/Mode Mute Preset-Up Preset-Down Power 10 11 12 13 14 15 16 17 18 Band Play/Enter PTT (Push to Talk) On-Hook Off-Hook Fan-Up* Fan-Down* Temp-Up* Temp-Down* * Not applicable in this application Note: Some radios may not have these commands.
PAGE 7
STEERING WHEEL CONTROL SETTINGS (CONT.) Dual assignment legend TROUBLESHOOTING Resetting the AX-HYKIA4-SWC Function # Function Function # 1 2 3 4 5 6 7 8 9 Not allowed Not allowed Seek-Up/Next Seek-Down/Prev Mode/Source ATT/Mute Preset-Up Preset-Down Power 10 11 12 13 14 15 16 17 18 Function Band Play/Enter PTT On-Hook Off-Hook Fan-Up* Fan-Down* Temp-Up* Temp-Down* 1. The Blue reset button is located inside the AX-HYKIA4-SWC interface, between the two connectors.
PAGE 8
AX-HYKIA4-SWC I N S TA L L AT I O N I N S T R U C T I O N S If you are having difficulties with the installation of this product, contact our Tech Support line either by phone at 1-800-253-TECH, or email at techsupport@metra-autosound.com. Before doing so, look over the instruction booklet a second time and ensure that the installation was performed exactly as the instruction booklet is stated. Have the vehicle apart and ready to perform troubleshooting steps before contacting Metra/Axxess Tech Support.