Owner's Manual

ManualsBrandsMetra ManualsAudio accessories & installationDash Kit

Table Of Contents

Installation Instructions

METRA. The World’s best kits.

™

metraonline.com1-800-221-0932

REV. 9/22/2015 INSTDP-7363B

CAUTION: Metra recommends disconnecting the

negative battery terminal before beginning any

installation. All accessories, switches, and especially

air bag indicator lights must be plugged in before

reconnecting the battery or cycling the ignition.

NOTE: Refer to the instructions included with the

aftermarket radio.

Installation instructions for part DP-7363B

• ISO DIN radio provision with pocket

• ISO Double DIN radio provision

• Painted matte black

• A) Radio trim panel • B) Radio brackets • C) Steering column cover bracket • D) Pocket

• E) (4) #8 x 3/8” Phillips screws • F) (8) #4 x 3/8” Phillips screws • G) (7) Panel clips

20;-,(;<9,:

20;*64765,5;:

>0905.(5;,55(*655,*;065: (sold separately)

Wiring Harness: • 70-7304, HYBL-04

Antenna Adapter: • Not required

• Phillips screwdriver • Panel removal tool

;663:9,8<09,+

Hyundai Sonata 2015-up

DP-7363B

DEF

Dash Disassembly

– Hyundai Sonata 2015-up ..................................2-3

Kit Assembly

– ISO DIN radio provision with pocket ...................... 4

– ISO Double DIN radio provision ............................. 5

Table of Contents

Summary of content (6 pages)

PAGE 1
Installation instructions for part DP-7363B Table of Contents Hyundai Sonata 2015-up DP-7363B Dash Disassembly – Hyundai Sonata 2015-up ..................................2-3 Kit Assembly REV. 9/22/2015 INSTDP-7363B – ISO DIN radio provision with pocket...................... 4 20; -,(;<9,: • ISO DIN radio provision with pocket • ISO Double DIN radio provision • Painted matte black – ISO Double DIN radio provision .............................
PAGE 2
DP-7363B Dash Disassembly 1. Unsnap and remove the climate/ hazard/clock panel. (Figure A) 2. Unsnap and remove the trim panel on the drivers side of the dash and then remove (2) Phillips screws. (Figure B) 3. Unsnap the knee panel from under the steering wheel. (no need to completely remove this panel).
PAGE 3
DP-7363B Dash Disassembly 4. Unsnap and remove the panel above the instrument cluster. (Figure D) 5. Unsnap the top half of the steering column cover. (Figure E) 6. Remove (4) screws to remove the radio panel; (2) under the radio section, and (2) above the instrument cluster. (Figure F) Note: The top of the steering column cover will come with the large panel. (Figure D) (Figure E) 7. Remove (4) Phillips screws securing the radio and then remove the radio.
PAGE 4
DP-7363B Kit Assembly ISO DIN radio provision with pocket 5. Slide the radio into the assembly and secure with screws supplied with the radio. (Figure D) 1. To remove the factory steering column cover from the factory dash panel, pry (4) round retaining clips from where the leather meets the large panel. (Figure A) 2. Place the leather cover over the Metra radio trim panel, place the steering column bracket over the leather and secure with the (4) #4 x 3/8” Phillips screws supplied. (Figure B) 6.
PAGE 5
DP-7363B Kit Assembly ISO Double DIN radio provision 4. Locate the factory wiring harness and antenna plug in the dash and make all necessary connections to the radio. Metra recommends using the proper mating adapters from Metra and/or AXXESS. 1. To remove the factory steering column cover from the factory dash panel, pry (4) round retaining clips from where the leather meets the large panel. (Figure A) 2.
PAGE 6
Installation instructions for part DP-7363B KNOWLEDGE IS POWER REV. 9/22/2015 INSTDP-7363B Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians METRA. The World’s best kits.™ 1-800-221-0932 metraonline.