Instruction Manual

ManualsBrandsMetra ManualsLight BracketMeTra HE-BRK-FD4 Fog Light Bracket

Table Of Contents

HE-BRK-FD4

Install instructions

Metraonline.com

Metra Electronics Corp.

REV. 01/24/2023

INSTHE-BRK-FD4

TABLE OF CONTENTS

Installation............................................................2

- Bracket mounting...............................................2

- Bracket configuration.........................................3

- OE switch panel wiring.......................................4

- Routing...............................................................6

- Harness Hardwire.............................................10

TOOLS REQUIRED

Hand Tools

• Philips screw driver

• Panel tool

• T40 Torx®

• Wire stripper

• Wire crimper

Additional Supplies

• Cable ties (recommended)

Part Components

Product Features

Harness

• Fits up to 3 Heise LED cube lights per bracket, (1) HE-B950, or (1) HE-BD8 Heise

LED light bar.

• Increase safety and visibility by installing Heise LED fog lights within the front

bumper of your Ford Bronco with these stylish Fog Light Brackets. These brackets

use the OE mounting locations, so no drilling is required. A corrosion-resistant

black powder-coated finish adds style and durability. Up to three Heise cube lights

will fit on a bracket, and each bracket includes a wiring harness for easy installation

with Bronco auxiliary switch wiring

• Uses OE mounting locations for

installation

• Wiring harness included for easy

installation with Bronco auxiliary

switch wiring

• Black powder-coated brackets

Brackets

Fog Light Bracket

Fits Ford Bronco 2021-Up

- Routing path.......................................................5

Summary of content (12 pages)

PAGE 1
HE-BRK-FD4 0 Fog Light Bracket Fits Ford Bronco 2021-Up Install instructions TABLE OF CONTENTS Installation............................................................2 - Bracket mounting...............................................2 - Bracket configuration.........................................3 - OE switch panel wiring.......................................4 - Routing path.......................................................5 - Routing............................................................
PAGE 2
HE-BRK-FD4 Install instructions -Bracket mounting 1. Locate the (3) factory bolts at the top front edge inside each of the fog light cavities. (Figure 1 and Figure 2) 2. Using a T40 Torx®, remove these (6) bolts. (Figure 3) 3. Align the brackets so the bracket hump rises front to back, and the sweep angles towards the side of the vehicle. (Figure 4 and Figure 5) Figure 1 Figure 2 Figure 3 Figure 4 4. Mount the desired lights to the bottom side of the brackets (in a hanging orientation).
PAGE 3
HE-BRK-FD4 Install instructions -Bracket configuration 7. Adjust the position of the lights so that they are evenly spaced. At this time fully tighten the lights mounting bolts. Repeat for the other side.
PAGE 4
HE-BRK-FD4 Install instructions -OE switch panel wiring If the vehicle is equipped with the factory switch panel continue, if not go to harness hardwire on page 10. 1. Pull the hood release handle near the driver kick panel to release the hood. 2. Open the hood and locate the auxiliary switch wires located in the driver side corner of the engine bay by the firewall. (Figure 10) Figure 11 3.
PAGE 5
HE-BRK-FD4 Install instructions -Routing Routing path 5
PAGE 6
HE-BRK-FD4 Install instructions -Routing 6. Locate the black hood release cable running along the inside of the driver side fender. (Figure 12) 7. Cable tie the harness to the hood release cable (do not over-tighten), working down the fender and around to the front of the battery. 8.In front on the battery locate the large black harness going down towards the bottom of the engine bay. (Figure 13) Figure 12 Figure 13 6 HeiseLED.
PAGE 7
HE-BRK-FD4 Install instructions -Routing 9. Using the factory harness as a guide, route the harness down and out the driver side fog light cavity. (Figure 14 and Figure 15) 10. Plug in the driver side “set 1” connector to the center most cube light, “set 2” connector to the middle cube light, and “set 3” connector to the cube light nearest the driver side. *If using less that (3) lights, omit the same set(s) of connectors on both sides of the vehicle. Figure 14 Figure 15 11.
PAGE 8
HE-BRK-FD4 Install instructions Figure 20 -Routing 12. Feed the passenger side portion of the harness back through the fog light cavity and into the driver wheel well. 13. Pull the wheel well liner back and locate the large black harness running horizontally across the bottom of the engine bay. (Figure 18 and Figure 19) 14. Feed the passenger portion of the harness across to the front passenger wheel well, securing the harness to the factory harness along the way.
PAGE 9
HE-BRK-FD4 Install instructions -Routing 15. 5. Feed the passenger portion of the harness f the passenger wheel well into the passenger fog light cavity. (Figure 22) 16. 6. Plug in the passenger side “set 1” connector the center most cube light, “set 2” connector to the middle cube light, and “set 3” connector to the cube light nearest the passenger side. 17. 7. Secure any excess cab 18. 8. Reinstall screw clips in both wheel wel 19. 9.
PAGE 10
HE-BRK-FD4 Install instructions -Harness hardwire 1. Open the hood and connect the harness as shown below. a. Ground the single black wire from the harness marked “chassis ground” to a factory grounding point in the engine bay. b. A switch, fuse holder, and relay will be need for each “set” wire (brown, blue/orange, & yellow/ orange). (Figure 23) 2. Continue with harness routing, page 5. Figure 23 10 HeiseLED.
PAGE 11
HE-BRK-FD4 Install instructions Document date of purchase, and place of purchase.
PAGE 12
HE-BRK-FD4 Install instructions Thank you for purchasing from Metra Electronics! We’re excited to see your installs, scan the QR to share on our Instagram. If you have any questions, comments, feedback on the product, please contact our tech support email via techsupport@metra-autosound.com. Don’t forget to Visit HeiseLED.com to view the available installation parts and accessories.