RADIANCE R200 PREMISE SERVICE PLATFORM MAN FD PWR LK RX DIS LBK LK RX DIS LBK Models: R200-AC / R200-DC 100 BASE T X x II S M FX Installation & User Guide
Radiance Series R200: R200-AC _____ Single slot platform with internal AC power supply R200-DC _____ Single slot platform with internal DC power supply Accessories: R200-WM _____ Wall mounting bracket The following is a listing of available Radiance products. Refer to each product’s installation and user guide for operational features.
Table of Contents Radiance R200 Premise Service Platform Installation & User Guide Overview .............................................................................................................. 4 Installation Guide ................................................................................................ 5 STEP 1: Unpack the Platform and Accessories ............................................. 5 STEP 2: Choose an Appropriate Location ....................................................
Overview The Radiance R200 Premise Service Platoform is the ideal solution for the installation of a single Radiance access line card at a remote site. While the R200 supports all single-slot interface line cards, it provides an especially cost effective way to manage a standalone access line card at the customer site. The R200 features a solid metal housing and an internal AC or DC power supply.
Installation Guide Follow the simple steps outlined in this section to install and start using the Radiance R200 Premise Service Platform. NOTE: Electrostatic discharge precautions should be taken when handling any line card. Proper grounding is recommended (i.e., wear a wrist strap).
3 Install the Line Card The R200 Premise Service Platform supports one single-slot Radiance interface line card. A Radiance line card offers the ease of plug-andplay installation and is hot-swappable. Refer to the card’s documentation for detailed installation instructions. Before installing any card, note the following: • Remove the temporary slot protector by turning the thumb screw counterclockwise and removing the blank panel. • Set all switches and/or jumpers on the line card.
4 5 Connect to the Network 6 Apply Power to the Platform To connect to the network, refer to the card’s installation and user guide for information about the cable types and lengths supported. Attach the Grounding Lug (R200-DC Only) On the back panel, the R200-DC has a small hole where a grounding lug must be installed. The hole is marked with the grounding symbol. Use a 6-32 screw to fasten the lug (not provided) to the platform.
DC plug connector wire leads • Insert the plug connector into the header on the R200 and tighten the two screws. + 48 VDC 1 AMP DISCONNECT ALL POWER SOURCES BEFORE SERVICING + • Turn ON the DC voltage source. • Verify proper power connection and operation by observing that the power (PWR) LED on the line card is lit. AC Power Supply Connections For AC connections, follow these guidelines: • Insert the power cord to the receptacle on the R200-AC. • Connect the power cord plug to the AC power source.
User Guide This section contains information regarding the technical specifications and warranty for the Radiance R200 Premise Service Platform.
Product Safety, EMC and Compliance Statements This equipment complies with the following requirements: • UL • CSA • CE • EN60950 (safety) • FCC Part 15, Class A • EN55022-A (emissions) • EN55024: 1998 (immunity) • DOC Class A (emissions) This product shall be handled, stored and disposed of in accordance with all governing and applicable safety and environmental regulatory agency requirements. The following FCC and Industry Canada compliance information is applicable to North American customers only.
Warranty and Servicing Three-Year Warranty for the Radiance R200 Premise Service Platform Metrobility Optical Systems, Inc. warrants that every Radiance product will be free from defects in material and workmanship for a period of THREE YEARS from the date of Metrobility shipment. This warranty covers the original user only and is not transferable.
Product Manuals The most recent version of this manual is available online at http://www.metrobility.com/support/manuals.htm To obtain additional copies of this manual, contact your reseller, or call 1.877.526.2278 or 1.603.880.1833 Product Registration To register your product, go to http://www.metrobility.com/support/registration.asp 25 Manchester Street, Merrimack, NH 03054 USA tel: 1.603.880.1833 • fax: 1.603.594.2887 www.metrobility.
