RADIANCE R400 PREMISE SERVICE PLATFORM M M M M PWR FL Model: R400-2HS-1A LK Installation & User Guide RX TX LK RX TX SLOT 2 10/100 FX AT LK AT LK A B R ER PWR MGT-10 1 2 C O N S O L E SLOT 1
Radiance Series R400 Premise Service Platform: R400-2HS-1A ______ 2-slot platform; single external AC power supply Accessories: R400-AC _________ AC power supply and line cord The following is a listing of available Radiance products. Refer to each product’s specific installation and user guide for operational features.
Table of Contents Radiance R400 Premise Service Platform Installation & User Guide Overview .............................................................................................................. 4 Installation Guide ................................................................................................ 6 STEP 1: Unpack the Platform and Accessories ............................................. 6 STEP 2: Choose an Appropriate Location ....................................................
Overview The Radiance R400 Premise Service Platform is the ideal solution for the management of remote sites where a small platform is preferred. The R400 supports all Radiance single-slot line cards and gives you the flexibility to mix and match cards to meet your specific network requirements. Use both slots for connectivity, or use one slot for connectivity and the other for management. With their compact design, two platforms fit into a standard 19-inch rack with an added tray.
Related Documentation Refer to the following documents for additional information: • Radiance 10Mbps Single Interface Line Cards Installation & User Guide • Radiance 100Mbps Single Interface Line Cards Installation & User Guide • Radiance 10Mbps Redundant Interface Line Cards Installation & User Guide • Radiance 100Mbps Redundant Interface Line Cards Installation & User Guide • Radiance 1000Mbps Redundant Interface Line Cards Installation & User Guide • Radiance 10/100Mbps Interface Line Cards Installation
Installation Guide Follow the simple steps outlined in this section to install and start using the Radiance R400 Premise Service Platform. NOTE: Electrostatic discharge precautions should be taken when handling any line card. Proper grounding is recommended (i.e., wear a wrist strap).
2 Choose an Appropriate Location The Radiance R400 is intended for use in office and industrial environments. Attach the four rubber feet to the bottom of the unit and place it on a flat surface. The feet provide a space for air circulation. The R400 may be oriented in any manner that allows you to make the physical connection to the power source and leaves a minimum of six (6) inches of space around it for proper ventilation.
3 Install the Line Cards The R400 Premise Service Platform supports two single-slot Radiance line cards in any combination. These cards offer the ease of plug-andplay installation and are hot-swappable. Refer to each card’s documentation for detailed installation instructions. Before installing any card, note the following: • Remove the temporary slot protectors by turning the thumb screws counterclockwise and removing the blank panels. • Line cards can be installed into either slot.
• Line the edges of the board with the slot guides and slide the card in until the edges are flush and even with the front of the unit. Do not force the card into the slot unnecessarily. It should slide in easily and evenly. • Secure to the platform by turning the thumb screw clockwise until snug. The line card is now ready for connection to the network. 4 Connect to the Network Connecting the Management Card The management card supports 10Base-T Ethernet.
6 Apply Power to the Platform Power is provided to the platform from the desktop power supply. Each R400 is shipped with one 90-264V AC external power supply. The power supply is equipped with an S760 hollow-type plug for insertion into the power input jack located on the back of the platform. To connect to the power source, the AC power supply provides a standard IEC 320-type AC power receptacle. The R400 supports a secondary power supply if redundant power is required.
• Verify proper power connection and operation via the LEDs labeled “A” and “B” on the management card. These LEDs correspond to the primary and secondary power supplies, respectively. A steady green light indicates the platform is receiving power. When two power supplies are installed and active, both LEDs are lit simultaneously. Refer to Operating Features of the Load-Sharing Power Supply in the User Guide section for further details.
7 Boot the Management Card Management of the Premise Service Platform is provided through a local console, Metrobility’s NetBeacon or WebBeacon software, or any SNMP network management application via a PC. WebBeacon is embedded in the management card. SNMP is supported on many general network platforms: SunNet Manager, HP OpenView for UNIX, HP OpenView for NT, SNMPc and others. Following power-up of the platform, the boot image is automatically executed.
User Guide This section contains information regarding certain operating features and maintenance instructions for the Radiance R400 Premise Service Platform. Management Card The management card is the Simple Network Management Protocol (SNMP) agent for the Radiance R400. Connected via the backplane to the cards in the platform, the management card reports individual board status to a local console, Metrobility’s NetBeacon software or any SNMP application.
Platform Technical Specifications Power Input _________________________________________ 90-264V AC, 50-60Hz Output __________________________________________ 12V DC, 2.
Operating Features of the Load-Sharing Power Supply The R400-AC load-sharing AC power supply is designed for use with the R400 platform and provides 30W of power. The R400-2HS-1A is shipped with one power supply, however, the unit can be upgraded with a second power supply. When an R400 platform is equipped with two load-sharing power supplies, they operate in tandem and share the load.
Topology Solutions Radiance R400 Switch Radiance R400 Switch Radiance R400 Switch 100Mbps Enterprise Switch Radiance R5000 Central Service Platform with Management Workstation Twisted-pair Links F/O Links 16 User Guide
Radiance R400 Switch Building 1 Radiance R400 Switch Building 2 Radiance R400 Switch Building 3 Radiance R5000 Central Service Platform with Management Workstation 100Mbps Enterprise Switch Main Building Twisted-pair Links Singlemode F/O Links Radiance R400 Premise Service Platform 17
Product Safety, EMC and Compliance Statements This equipment complies with the following requirements: • UL • CSA • EN60950 (safety) • FCC Part 15, Class A • EN55022-A (emissions) • EN55024 (immunity) • IEC 825-1 Classification • Class 1 Laser Product • DOC Class A (emissions) This product shall be handled, stored and disposed of in accordance with all governing and applicable safety and environmental regulatory agency requirements.
Warranty and Servicing Three-Year Warranty for the Radiance R400 Premise Service Platform Metrobility Optical Systems, Inc. warrants that every Radiance product will be free from defects in material and workmanship for a period of THREE YEARS from the date of Metrobility shipment. This warranty covers the original user only and is not transferable.
Product Manuals The most recent version of this manual is available online at http://www.metrobility.com/support/manuals.htm Product Registration To register your product, go to http://www.metrobility.com/support/registration.asp 25 Manchester Street, Merrimack, NH 03054 USA tel: 1.603.880-1833 • fax: 1.603.594.2887 www.metrobility.
