T2 HD zapbox Digital TV Receiver USER MANUAL
Contents Accessories ............................................................ 2 Introduction ............................................................. 2 Safety Precautions ................................................. 2 Overview of the Remote Control ............................ 4 Viewing Controls and Connections of the Set Top Box ......................................................................... 5 Front Panel ......................................................... 5 Rear Panel .......
corresponding instructions of this handbook prior to the first usage of the device, even when the usage of electronic devices is familiar to you. Features • DVB and VBI teletext. • 200 channels • DVB 7 days event information (7-days EPG). • TV scart (with RGB and CVBS support). • HDMI output. • Automatic tuning. • Please read the chapter SAFETY PRECAUTIONS and INFORMATION. Carefully keep the handbook as future reference.
Important Safety information Mains supply This equipment is designed to operate from a 220-240 Volt, 50Hz AC mains supply. Other power sources may damage it. Check that the rating label on the back of the mains adapter states 220-240V AC before you plug it in for the first time. Mains lead We have fitted this equipment with a mains adapter with a standard plug fitting. x If the mains lead becomes damaged it must be replaced with an approved lead of the same type and rating to avoid a hazard.
Overview of the Remote Control Standby Displays Interactive Services (if available) WIDE .
Viewing Controls and Connections of the Set Top Box Front Panel PROG DOWN DISPLAY PROG UP ON/OFF KEY 35027073 Rear Panel HDMI OUTPUT . 1 2 OPTICAL AUDIO OUT ETHERNET 3 4 5 6 7 1. ANTENNA IN : You can connect the antenna to the aerial input of the box. 2. TV OUT : You can use ‘’aerial TV out’’ to connect aerial to your TV. 3. ETHERNET: Use this to connect the box to an active LAN connection. 4.
Inserting Batteries in the Remote Control • Remove the battery cover located on the back of the remote control by gently pulling back the indicated part. • Insert two AAA/R3 (2 X 1.5Volt) or equivalent type batteries inside. Place the batteries in the right direction observing the polarity symbols (+/-) and replace the battery cover. • While using the remote control, you should direct it towards the front panel of the receiver. Remote range is approximately 7m/23ft.
Power Connection IMPORTANT: The set-top box is designed to operate on 12V DC. For this, an adaptor is used which supplies a 12V DC voltage. Connect this adaptor to a mains socket that supplies 220-240V AC,50Hz. • After unpacking, allow the set-top box to reach the ambient room temperature before you plug it in to the mains for the first time. ∘ To Power Input DC12V terminal on the set-top-box Antenna Connection This illustration shows how to connect an antenna.
First Time Installation IMPORTANT: Ensure that the aerial is connected before switching on the set-top-box for the first installation. • When the set-top-box is operated for the first time, installation wizard will guide you through the process. First, TV Type selection menu will be displayed on screen: • Select Yes or No by using “ ”/“ ” buttons.
Volume Up / Down • You can increase or decrease the volume by using V+ / V- buttons. • To exit from a menu screen, you can press MENU button. • The following items are located in the main menu screen: • The volume level selected will remain set, even when the receiver is turned off and on again, until you change volume again. • The audio volume adjustment for the receiver is independent of the volume control on your TV set.
• If the selected channel is password protected, parental lock password will be asked. If the correct code is entered, selected channel can be watched. Operating the Channel List • Press “ ”/“ ” button to select the channel that will be processed. • Press “ ”/“ ” button to select a function on Channel List menu. • Use P+/P- buttons to move page up or down. current character, i.e., ‘b’ character becomes ‘a’ by pressing “ ” and ‘c’ by pressing “ ”. • Pressing the numeric buttons ‘0...
Viewing Electronic Programme Guide (EPG) You can view the electronic programme guide (EPG) to view information about available programmes. Select Programme Guide from the main menu by using “ ”/“ ” buttons. Press OK to continue. HINT: You can also press GUIDE button to view the EPG menu. • Press “ ”/“ ” buttons to navigate through channels. • Press “ ”/“ ” buttons to navigate through the programme list. • EPG menu displays available information on all channels.
• Select Active Channels by using “ ”/“ ” button. AC3 Audio • You can select a broadcast type option from the list by using “ ”/“ ” button. Available modes are: TV Only, Radio Only, Text Only, Favourites or Show All (if available). • Highlight the AC3 Audio item by pressing “ ”/“ ” buttons. Use the “ ”/“ ” buttons to set the AC3 Audio as On or Off. • Press the MENU button to save the recent changes and exit.
be broadcast. If found, the box will download new software automatically. This operation will normally take approximately 30 minutes. • You can use this feature, only if the broadcaster supports that additional narration track. • You can enable or disable automatic upgrade by setting Automatic Scanning option. • You can manually search for new software by selecting Scan for upgrade. • To upgrade software via USB, you can use USB Upgrade setting (Optional).
• Audio: Sets the preferred audio language. • Subtitle: Sets the subtitle language. Selected language will be seen in subtitles. • Guide: Sets guide language. Current (*) (*) These settings can only be changed if the broadcaster supports them. Otherwise, settings will not be available for change. • Audio: Changes the audio language for the current channel. • Subtitle: Sets the subtitle language for the current channel.
• After you select Yes, factory settings will be loaded. • Installation wizard will guide you through the installation process. See the section, “First Time Installation” in previous chapters for more information on this process. OSD Warning Messages • Some warning messages may appear on the screen indicating that a related function may not be working properly. No Signal • When the box receives no signal (e.g. the antenna cable is disconnected), “NO SIGNAL” message will be displayed on the screen.
Troubleshooting Problem Possible Reasons What To Do The LED indicator does not glow. Check if the AC Adaptor is plugged into the power socket and switched on. Connect DC lead to 12 Volt DC socket on the box ensuring its all the way home. No picture or sound. No signal or weak signal. Check the aerial and video connections (scart/HDMI). • Press the STANDBY button. The remote control is not working. • The set-top-box is in standby. • Remote control is out of range. • Batteries are exhausted.
General Characteristics Supply Voltage for set-top box: 12 V DC Supply Voltage for DC Adaptor : 220 - 240 V AC ~ 50Hz Input Frequency 470Mhz-862Mhz Maximum Power consumption 15 W Typical Power consumption 8W Standby Power Consumption <1 W USB (optional) Current Limit 500mA Operating temperature 5ºC to +40ºC Storage temperature -20ºC to +70ºC Humidity 25 to 75 % rel Physical dimensions 295 x 170 x 40 mm Weight 900 g Hardware Configuration Main Processor MPEG Decoder NEC EMMA3SL/HD F
Audio Output 2 Vrms, 0 dBfs / Z = 10 kohm Digital Audio Output Optical SPDIF A / V & Data In / Out Scart TV scart RGB Video Output TV scart CVBS Video Output TV scart Analogue Audio Output TV scart Digital Audio Output Optical output HDMI Output HDMI USB Input USB 2.0 High Speed (Optional) (For service use only.) NOTE: The USB port is used for software upgrading only. USB connector does not have any other functions such as playing audio or picture files.
Product Guarantee This product is guaranteed against manufacturing defects for a period of 1 Year This does not cover the product where the fault is due to misuse, abuse, use in contravention of the instructions, or where the product has been the subject of unauthorised modifications or alterations, or has been the subject of commercial use. In the event of a problem with the product within the guarantee period please return it to your nearest store.
Following information is only for EU-member states: The use of the symbol indicates that this product may not be treated as household waste. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.
