Installation Sheet

INSTALLATION INSTRUCTIONS
Item#N7104-258B (Convertible Lamps for Pendant )
READ AND SAVE THESE INSTRUCTIONS
W A R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
Page: 1/3
Fig. 1
Fig. 2
LA-2477E
PREPARATION (Fig. 1)
1.
Shut off the power at the fuse box or circuit breaker. If
necessary, remove the old fixture including the
mounting
hardware.
2. Carefully remove the fixture from the carton and check
that all parts are included as shown in the illustration.
ASSEMBLING THE FIXTURE WITH CHAIN LOOP (Fig.1)
3. Determine the desired hanging height and thread rods
(F1, F2 and F3) to the nipple (I) of the fixture body (L).
Then attach loop (H1) by screwing in to rod (F1).
Note:
remove the nipple if installing with one 6” rod only.
4. Attach the quick link (G)
to loop (H1) and loop (H2) on the
canopy (D), carefully feed the wire over loop (H1), quick
link (G) and loop (H2).
5. Thread screws (A) into the pre-
drilled holes in the circular
strap (B) spaced the same distance apart as the holes in
the canopy (D).
6.
Attach the circular strap (B) to the Junction box using
mounting screws (C) (Size: #8-32N*L0.5”
). The side of the
circular strap marked “GND” must face out.
CONNECTING THE WIRES (Fig. 2)
7. At this point, connect the electrical wires as shown in
figure 2, making sure that all wire connectors are secured.
If your outlet h
as a ground wire (green or bare copper),
connect the fixture’s ground wire to it
. Otherwise, connect
the fixture’s ground wire
directly to the circular strap using
the green screw provided.
8. Tuck the wire connectors neatly into the ceiling Junction
Box and then raise the canopy all the way to the ceiling.
COMPLETING THE INSTALLATION (Fig. 1)
9.
Thread screws (A) into canopy (D), and secure with
knurled knobs (E).
10. Hang the crystal drops (N) and the crystal ball (M)
to
proper position of fixture body (L).
11. Place the tube (K) over the socket of the fixture body (L).
12. Install the light bulb(s) (J) (not included)
in accordance
with the fixture’s specifications.
(DO NOT EXCEED THE
MAXIMUM WATTAGE RATING!).
(NE PAS DEPASSER
LA PUISSANCE NOMINALE MAXIMALE!)
13. Please note that this lamp is convertible from pendant to a
semi-flush. The wire length is 144” for pendant, 7” for Semi.
You can convert from a pendant to a semi-flush but once you
cut the wire you are not able to convert back to a pendant.
Your installation is
now complete. Return power to the junction
box and test the fixture.
Note:
Illustration (Fig. 1) on this manual is for installation
purposes only. It may or may not be identical to the fixture
purchased.
J
K
M
N
P
H2
F1
F3
F2
L
D
B
C
A
G
E
H1
F
I
Set
#
A
-
020
-Circular Strap
-Ground screw
-Mounting Screw*2
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
White
(Neutral)
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
Green
(Ground)
“
©
2015
Minka Lighting, Inc.
This product is protected by United States Federal
and/or State Law, including Patent and/or Copyright
laws.”