Instructions / Assembly

ManualsBrandsMetropolitan ManualsLightingSutton 3-Light Polished Nickel Drum Pendant to Semi-Flush with Clear Pressed Glass and White Silk Shades

INSTALLATION INSTRUCTIONS

Item#N7383-613 (New. 2022/05/15)

(Convertible lamps for pendant)

READ AND SAVE THESE INSTRUCTIONS

W A R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .

AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

Page: 1/2

Fig. 1

Fig. 2

LA-3537E

ASSEMBLING THE FIXTURE (Fig. 1)

Shut off the power at the circuit breaker and remove the

old fixture, including the mounting hardware.

Carefully unpack your new fixture and lay out all the parts

on a clean area. Ta

ke care not to lose any small parts

necessary for installation.

3. Secure rod (L) to fixture body (K) using screws (J)

. Then

place larger cloth shade (H) onto fixture body (K)

and

secure with screws (I).

Determine desired hanging height and thread rods

(F1,F2,F3) to all thread (G

) on fixture body (K). Attach

canopy (D) by threading

onto rod (F1). Carefully pass

wires through each rod during assembly. Note: Remove

all thread, if installing with one 6” rod only.

5. Attach mounting plate (A) to junction box (not inc

luded)

using mounting screws (B) (Size: #8-

32N*L0.5”). The side

of mounting plate marked “GND” and two convex points

must face out.

CONNECTING THE WIRES (Fig. 2)

6. Connect the electrical wires as shown in Fig.2, making

sure that all wire connectors are secured. If your

junction

box

has a ground wire (green or bare copper), connect

fixture’s ground wire to it. Otherwise, connect fixture’s

ground wire directly to mounting plate (A) using

green

screw provided.

7. Tuck wire connections neatly into junction box.

FINISHING THE INSTALLATION (Fig.1)

8. Place

canopy (D) over mounting plate (A) and secure

with screws (E).

9. Install (3) three medium base bulbs (M) up to 60 watts

each or CFL or LED equivalent (not included) in

accordance with the fixture specification—

DO NOT

EXCE

ED THE MAXIMUM WATTAGE RATING! (NE PAS

DEPASSER LA PUISSANCE NOMINALE MAXIMALE!

10. Secure rod (W) into all thread (O). Then place

lower cloth

shade (Q) to fixture body (K) using screws (I).

11. Place glass shade (U) followed by metal washer (T) over

bottom of rod (W). Then fasten with hex nut (N).

12. Place metal cover (S) over rod (W)

and secure with finial

(V).

Your installation is now complete. Return power

to the junction

box and test the fixture.

Note: Illustration (Fig.1) on this manual is for installation

purposes only. It may or may not be identical to the fixture

purchased.

Set

143D

-Mounting plate

-Ground screw

-Mounting screw *2

FIXTURE

WIRES

Black or

Smooth

HOUSE

WIRES

Black

(Hot)

FIXTURE

WIRES

White or

Ribbed

HOUSE

WIRES

White

(Neutral)

FIXTURE

WIRES

Bare

Copper

(Ground)

HOUSE

WIRES

Green

(Ground)

Rod# W35-1-613 *1 (F1)

W35-1-613 *2 (F2)

W35-H-613 *1 (F3)

Summary of content (2 pages)

PAGE 1
INSTALLATION INSTRUCTIONS Item#N7383-613 (New. 2022/05/15) (Convertible lamps for pendant) READ AND SAVE THESE INSTRUCTIONS W A R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R . AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR. ASSEMBLING THE FIXTURE (Fig. 1) 1. Shut off the power at the circuit breaker and remove the old fixture, including the mounting hardware. 2. Carefully unpack your new fixture and lay out all the parts on a clean area.
PAGE 2
INSTALLATION INSTRUCTIONS Item#N7383-613 (New. 2022/05/15) (Convertible Lamps for SEMI Flush mount) READ AND SAVE THESE INSTRUCTIONS W A R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R . AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR. PREPARATION (Fig.3 & 4) 1. Loosen hex nut (P) by using wrench (C) (Not included). Carefully remove washer (R), lock washer (W), metal plate (W1), canopy (D) and swivel (S1). (Fig.