Specifications

Transmitter Multiparameter M400 5
© 11 / 08 Mettler-Toledo AG, CH-8606 Greifensee, Switzerland Transmitter Multiparameter M400
Printed in Switzerland 52 121 378
7 Sensor Calibration _____________________________________________________________________________________ 32
7.1 Enter Calibration Mode ____________________________________________________________________________
32
7.2 Conductivity Calibration ___________________________________________________________________________
32
7.2.1 One-point Sensor Calibration _______________________________________________________________
33
7.2.2 Two-point Sensor Calibration (4-electrode sensors only) __________________________________________
33
7.3 Oxygen Calibration _______________________________________________________________________________
33
7.3.1 One-Point Sensor Calibration ________________________________________________________________
33
7.3.2 Two Point Sensor Calibration (only available for Optical Sensors) ___________________________________
34
7.3.3 Process Calibration _______________________________________________________________________
34
7.4 pH Calibration ___________________________________________________________________________________
35
7.4.1 One point calibration _____________________________________________________________________
35
7.4.2 Two point calibration _____________________________________________________________________
36
7.4.3 Process calibration _______________________________________________________________________
36
7.4.4 mV calibration __________________________________________________________________________
36
7.5 Sensor Temperature Calibration _____________________________________________________________________
37
7.5.1 One-Point Sensor Temperature Calibration ______________________________________________________
37
7.5.2 Two – Point Sensor Temperature Calibration ____________________________________________________
37
7.6 Edit Sensor Calibration Constants (only for analog sensor) ________________________________________________
38
7.7 Sensor Verification
________________________________________________________________________________ 38
8 Configuration _________________________________________________________________________________________
39
8.2 Measurement ___________________________________________________________________________________
39
8.2.1 Channel Setup ___________________________________________________________________________
39
8.2.2 Temperature Source (Not used with ISM Sensors) ________________________________________________
40
8.2.3 pH / O
2
Parameter related settings ____________________________________________________________ 40
8.2.3.1 Conductivity Temperature Compensation _____________________________________________
40
8.2.3.2 pH Parameters _________________________________________________________________
41
8.2.3.3 Dissolved Oxygen Parameters _____________________________________________________
42
8.2.4 Set Averaging ____________________________________________________________________________
42
8.3 Analog Outputs __________________________________________________________________________________
43
8.4 Setpoints ______________________________________________________________________________________
44
8.5 Alarm / Clean ___________________________________________________________________________________
45
8.5.1 Alarm __________________________________________________________________________________
45
8.5.2 Clean __________________________________________________________________________________
46
8.6 ISM Set up (only available if an ISM sensor is connected) _________________________________________________
46
8.6.1 Sensor Monitoring ________________________________________________________________________
46
8.6.2 CIP Cycle Limit ___________________________________________________________________________
47
8.6.3 SIP Cycle Limit ___________________________________________________________________________
48
8.6.4 Autoclaving Cycle Limit ____________________________________________________________________
48
8.6.5 Reset ISM Counter / Timer ___________________________________________________________________
49
8.7 Display ________________________________________________________________________________________
49
8.7.1 Measurement ____________________________________________________________________________
49
8.7.2 Resolution ______________________________________________________________________________
50
8.7.3 Backlight _______________________________________________________________________________
50
8.7.4 Name __________________________________________________________________________________
50
8.7.5 ISM Sensor Monitoring (available when ISM sensor connected) _____________________________________
51
8.8 Hold Analog Outputs ______________________________________________________________________________
51
9 System ______________________________________________________________________________________________
52
9.1 Set Language ___________________________________________________________________________________
52
9.2 USB ___________________________________________________________________________________________
52
9.3 Passwords _____________________________________________________________________________________
53
9.3.1 Changing Passwords ______________________________________________________________________
53
9.3.2 Configuring Menu Access for Operator _________________________________________________________
53
9.4 Set / Clear Lockout ________________________________________________________________________________
54
9.5 Reset __________________________________________________________________________________________
54
9.5.1 Reset System ____________________________________________________________________________
54
9.5.2 Reset Meter Calibration ____________________________________________________________________
54
9.5.3 Reset Analog Calibration ___________________________________________________________________
55
9.6 Set Date & Time _________________________________________________________________________________
55
10 PID Setup ____________________________________________________________________________________________
56
10.1 Enter PID Setup __________________________________________________________________________________
57
10.2 PID Auto / Manual ________________________________________________________________________________
57
10.3 Mode __________________________________________________________________________________________
58
10.3.1 PID Mode _______________________________________________________________________________
58