Mettler Toledo PS2+ : Specifications : Page 7

CONTENTS

1

11

1 Introduction

IntroductionIntroduction

Introduction................................

................................................................

................................1-1

1-11-1

1-1

Standard Features

Standard FeaturesStandard Features

Standard Features................................

................................................................

............................................

........................

............ 1-1

1-11-1

1-1

Optional Accessories

Optional AccessoriesOptional Accessories

Optional Accessories................................

................................................................

........................................

................

........ 1-2

1-21-2

1-2

Specifications

SpecificationsSpecifications

Specifications................................

................................................................

..................................................

....................................

.................. 1-2

1-21-2

1-2

Physical Dimensions.....................................................................................................................1-2

Power Requirements.....................................................................................................................1-3

Environmental Requirements........................................................................................................1-3

Standards Compliance

Standards ComplianceStandards Compliance

Standards Compliance................................

................................................................

.....................................

..........

..... 1-4

1-41-4

1-4

Electrical Interfaces ......................................................................................................................1-5

2

22

2 Installation and Calibration

Installation and CalibrationInstallation and Calibration

Installation and Calibration................................

................................................................

...........................................

......................

...........2-1

2-12-1

2-1

Unpacking and Setup

Unpacking and SetupUnpacking and Setup

Unpacking and Setup................................

................................................................

.......................................

..............

....... 2-1

2-12-1

2-1

Installation.....................................................................................................................................2-1

Basic Information

Basic InformationBasic Information

Basic Information ................................

................................................................

............................................

........................

............ 2-4

2-42-4

2-4

The Display...................................................................................................................................2-4

Keys and Navigation.....................................................................................................................2-5

Initial Calibration using GEOCAL™

Initial Calibration using GEOCAL™Initial Calibration using GEOCAL™

Initial Calibration using GEOCAL™................................

................................................................

.....................................................

..........................................

..................... 2-6

2-62-6

2-6

Power up Sequence.......................................................................................................................2-8

Full Calibration

Full CalibrationFull Calibration

Full Calibration................................

................................................................

................................................

................................

................ 2-8

2-82-8

2-8

Metrological Seal Installation

Metrological Seal InstallationMetrological Seal Installation

Metrological Seal Installation................................

................................................................

...........................................................

......................................................

........................... 2-10

2-102-10

2-10

3

33

3 Configuring the Setup Parameters

Configuring the Setup ParametersConfiguring the Setup Parameters

Configuring the Setup Parameters ................................

................................................................

.................................

..

.3-1

3-13-1

3-1

Basic Information

Basic InformationBasic Information

Basic Information ................................

................................................................

............................................

........................

............ 3-1

3-13-1

3-1

Program Block Access..................................................................................................................3-1

Exit Setup......................................................................................................................................3-1

Configuring Setup Parameters

Configuring Setup ParametersConfiguring Setup Parameters

Configuring Setup Parameters................................

................................................................

...........................................................

......................................................

........................... 3-2

3-23-2

3-2

Push Button Zero Program Block.................................................................................................3-2

Zero Cursor Program Block..........................................................................................................3-3

Power-up Unit Program Block......................................................................................................3-3

Build Program Block ....................................................................................................................3-3

Alternate Units Program Block.....................................................................................................3-4

Mode Program Block....................................................................................................................3-4

Filter Program Block.....................................................................................................................3-5

Baud Program Block.....................................................................................................................3-5

ASCII Program Block...................................................................................................................3-5

Parity Program Block....................................................................................................................3-6

Stop Program Block......................................................................................................................3-6

Protocol Program Block................................................................................................................3-6

Sleep Program Block ....................................................................................................................3-7

GEOCAL™ Program Block .........................................................................................................3-7

Calibration Program Block ...........................................................................................................3-7

End Program Block.......................................................................................................................3-8

4

44

4 Operating Instructions

Operating InstructionsOperating Instructions

Operating Instructions................................

................................................................

..................................................

....................................

..................4-1

4-14-1

4-1

Keypad and Display

Keypad and DisplayKeypad and Display

Keypad and Display................................

................................................................

.........................................

..................

......... 4-1

4-14-1

4-1

Operator Functions

Operator FunctionsOperator Functions

Operator Functions................................

................................................................

...........................................

......................

........... 4-1

4-14-1

4-1

Parcel Weighing............................................................................................................................4-2

Unit Switching ..............................................................................................................................4-2

Zeroing the Scale with an Empty Container.................................................................................4-2