ECONOMY COUNTING SCALE OPERATION & SERVICE MANUAL Models XTCII ECONOMY COUNTING SCALE www.mt.
ECONOMY COUNTING SCALE 2 ABOUT THIS MANUAL AND MT EXPRESS Thank you for purchasing an MT Xpress product. All of our equipment is assembled and packed with great care. If you should find any incorrect item, please contact your Xpress Dealer immediately. MT Xpress products are Weights & Measures approved precision weighing instruments. However, you may want to obtain official certification through your supplier or local Weights & Measures office.
ECONOMY COUNTING SCALE 3 FCC APPROVAL This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
ECONOMY COUNTING SCALE CONTENTS SAFETY NOTICE............................................................................................................................. 5 PREPARING THE SCALE FOR USE ..................................................................................................... 6 ENVIRONMENT ..................................................................................................................... 6 UNPACKING AND ASSEMBLY.................................................
ECONOMY COUNTING SCALE 5 SAFETY NOTICE Product safety is a fundamental concern at MT Xpress. Use common sense and follow the simple precautions listed below to ensure your safety and to optimize the use and performance of this product. − Read this manual before operating or servicing this product. Save this manual for future reference. − Observe safety warnings located throughout this manual. − Use caution when lifting or moving heavy equipment.
ECONOMY COUNTING SCALE 6 PREPARING THE SCALE FOR USE The Xpress XTCII is a new generation counting scale. With high internal and display resolution as well as a unique profile, the XTCII can widely be used in counting applications in the electronics, metals, plastics and other such industries. The Xpress XTCII is ready to use right out of the box. This manual provides not only the detailed information on how to operate the scale, but also useful messages for service and maintenance.
ECONOMY COUNTING SCALE 7 1. Place the scale on a flat surface. 2. Remove the protective screws (only for the 6 lb and 15 lb scales) 3. Mount four rubber gaskets onto each spider foot (only for the 6 lb and 15 lb scale). 4. Put the platter on the spider (aluminum plate). Ensure that the platter is properly aligned. 5. Connect the scale to the power outlet using the included adapter. 6. Level the scale by adjusting the four rubber feet until the leveling bubble is centered in the level indicator.
ECONOMY COUNTING SCALE 8 YOUR XPRESS SCALE AT A GLANCE DISPLAY KEYPAD Key thru Name Function Decimal Enters a decimal point/Toggles alarm beep Numeric Data entry (0-9) Sample Initiates sampling APW Initiates Average Piece Weight (APW) entry Zero Zeroes the scale Tare Subtracts tare value and switches from gross to net mode Accumulation Adds the accumulator counts or recalls accumulation Recall Recalls the accumulated quantity and times Alarm Sets the range for quantity or weight alar
ECONOMY COUNTING SCALE 9 OPERATING YOUR SCALE ZERO Press to capture a new center of zero if the scale is in gross weight mode and the weight on the scale is stable (e.g. 0.5000 lb, as above shown, the cursor ‘Stab’ is on). The cursor “0” is lit when a new center of zero is captured. TARE key subtracts the weight of the object on the scale platform from subsequence indications Pressing the of weight. Tare is most often used to subtract the weight an empty container.
ECONOMY COUNTING SCALE 10 COUNTING Counting by Sampling Place the samples on the platter (e.g. 20 pieces weights 0.05 lb as shown above). Press the key to sample. The QTY window displays SPL. Enter the sample quantity 20, and then press the key to confirm. Press the key to correct or clear the input figure. The Wt window displays the sample Weight; the APW window displays Average Piece Weight of samples and the QTY displays the sample Quantity.
ECONOMY COUNTING SCALE 11 If you know the APW. . . If you know the APW of your goods, the APW can be entered directly instead of sampling. and enter the APW (e.g. 0.002 lb) of one Place the goods on the scale (e.g. 0.05 lb). Press the key piece. The QTY window displays “Single” and the entered APW is displayed in the APW window. Press to confirm. The QTY window displays now the total quantity of pieces (e.g. 25). You may press the key to correct or clear the input figure.
Temporarily Disable the Alarm Beep For all functions, the alarm beep can be deactivated by pressing the key reactivate the alarm beep. ECONOMY COUNTING SCALE . Pressing again will Weight Alarm within a Range to set the alarm range. The If weight alarm within a range is activated in the Setup Mode, press the key QTY window displays ‘Lo 1’ to remind you to enter the lower limit of the alarm range. The entered lower range is displayed in the APW window (e.g. 0.500 lb).
ECONOMY COUNTING SCALE 13 SPECIAL MODES – SETUP MODE ENTERING SETUP MODE Press and hold for three seconds to enter the Setup Mode. If you change the display resolution in the Setup Mode, the scale will perform its power-up process after exiting the Setup Mode. If the resolution remains unchanged, the scale will return to its previous state.
ECONOMY COUNTING SCALE 14 CLEANING AND MAINTAINING YOUR SCALE WARNING DISCONNECT ALL POWER TO THIS UNIT BEFORE INSTALLING, SERVICING, CLEANING, OR REMOVING THE FUSE. FAILURE TO DO SO COULD RESULT IN BODILY HARM AND/OR PROPERTY DAMAGE. CLEANING AND MAINTENANCE − DO NOT allow untrained personnel to operate, clean, inspect, maintain, service, or tamper with this equipment. − DO NOT attempt to remove the cover or to perform service/maintenance on the internal parts of the scale.
ECONOMY COUNTING SCALE 15 SERVICING YOUR SCALE For the following services, please contact your Xpress representative at www.mt.com/xpress. CAUTION WARNING DISCONNECT ALL POWER TO THIS UNIT BEFORE INSTALLING, SERVICING, CLEANING, OR REMOVING THE FUSE. FAILURE TO DO SO COULD RESULT IN BODILY HARM AND/OR PROPERTY DAMAGE.
ECONOMY COUNTING SCALE
ECONOMY COUNTING SCALE 17 GRAVITY ADJUSTMENT This scale has built-in compensation provisions to allow factory calibration, with destination correction capabilities, to compensate for variances on gravitational forces. If the scale is subjected to a different gravitational force at its destination location, this can be compensated for electronically by adjusting the geo value. The GEO value has 32 settings.
ECONOMY COUNTING SCALE 18 Example: 6 lb linearity calibration (S4.1=1) When the Wt window display S4.1 1, press the key the scale in linearity. to calibrate The scale displays SP 6, where 6 means the capacity is 6 lb, selects the capacity. Press to continue. Pressing The Wt window displays 2----. The scale will capture zero weight by . The scale should count down from 5. pressing the key The Wt window displays L 3. Put 3 lb weight on the scale, press to calibrate in half range.
ECONOMY COUNTING SCALE 19 BATTERY REPLACEMENT CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE OR CONNECTED IMPROPERLY. DISPOSE OF USED BATTERIES ACCORDING TO LOCAL LAWS AND REGULATIONS. Please replace the battery follow below steps: 1. Switch off the scale. 2. Open and remove the plastic battery cover on the rear of the XTCII. 3. Loosen the four M4 x 8 screws and remove the protective cover.
ECONOMY COUNTING SCALE 20 4. Carefully remove the power harness from the battery, replace a new battery and connect the terminal to the plug correctly. CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED WITH WRONG TYPE OR CONNECTED IMPROPERLY. CONNECT RED WIRE TO POSITIVE (+) BATTERY TERMINAL AND BLACK WIRE TO NEGATIVE (-) BATTERY TERMINAL! 5. Reinstall the protective cover and the plastic battery cover. 6. Switch on the scale and test for proper operation.
ECONOMY COUNTING SCALE 21 APPENDIX ERROR MESSAGES The scale will display an error message if a problem or an incorrect keyboard entry is sensed. The error codes are: Display The Wt window displays E11 Possible Cause RAM error The Wt window displays E16 ROM error The Wt window displays E18/E3 EPROM checksum error The Wt window displays E7 A/D convert error Troubleshooting 1. Restart the scale. 2. Recalibrate the scale. 3. Change the main PCB. 1. Restart the scale. 2. Recalibrate the scale. 3.
ECONOMY COUNTING SCALE 22 SPECIFICATIONS Model XTCII1003 XTCII1103 XTCII2003 XTCII2103 XTCII3003 XTCII3103 XTCII4003 XTCII4103 Maximum capacity (lb) 6 15 30 60 Verified resolution (lb) 0.002 0.005 0.01 0.02 Display resolution (lb) 0.0002, 0.0005, 0.001, 0.002 0.001, 0.002, 0.005 0.001, 0.002, 0.005, 0.01 0.002, 0.005, 0.01, 0.02 0.0002 0.0004 0.001 0.002 Recommend minimum APW (lb) Power supply AC AC/DC AC AC/DC AC AC/DC AC AC/DC Shipment weight (lb) 11 13.2 11 13.
ECONOMY COUNTING SCALE 23 GEO VALUE TABLE Use the following geo codes if you relocate your scale to a site other than the original location where it was calibrated.
ECONOMY COUNTING SCALE 24 PHYSICAL DIMENSIONS 13.5” 9.5” 4.5” 13.
ECONOMY COUNTING SCALE Notes 25
Notes ECONOMY COUNTING SCALE
Xpress Mettler-Toledo, Inc. 60 Collegeview Westerville, OH 43081 7/2004 MTX04-OM015.1E ECONOMY COUNTING SCALE www.mt.
