OPERATING INSTRUCTIONS ADDENDUM M SERIES MILO 60 High-Power Narrow Coverage Curvilinear Array Loudspeaker Addendum to MILO Operating Instructions (PN 05.132.095.01 A) Keep these important operating instructions. Check www.meyersound.com for updates.
DECLARATION OF CONFORMITY ACCORDING TO ISO/IEC GUIDE 22 AND EN 45014 Manufacturer's Name: Meyer Sound Laboratories Inc. Manufacturer's Address: 2832 San Pablo Avenue Berkeley, CA 94702-2204, USA declares that the products Product Name: MILO 60 conforms to the following Product Specifications Safety: EN60065: 1998 IEC60065: 1998 EMC: EN55103-1: 1997 emission1 EN55103-2: 1997 immunity2 This device also complies with EN 55103-1 & -2.
SYMBOLS USED These symbols indicate important safety or operating features in this booklet and on the chassis: ! Dangerous voltages: risk of electric shock Important operating instructions Frame or chassis Protective earth ground Pour indiquer les risques résultant de tensions dangereuses Pour indequer important instructions Masse, châssis Terre de protection Zu die gefahren von gefährliche spanning zeigen Zu wichtige betriebsanweisung und unterhaltsanweisung zeigen Rahmen oder chassis Die schut
SAFETY SUMMARY English - - - - - - To reduce the risk of electric shock, disconnect the loudspeaker from the AC mains before installing audio cable. Reconnect the power cord only after making all signal connections. Connect the loudspeaker to a two-pole, three-wire grounding mains receptacle. The receptacle must be connected to a fuse or circuit breaker. Connection to any other type of receptacle poses a shock hazard and may violate local electrical codes.
Operating Instructions Addendum: MILO 60 MILO™ 60 HIGH-POWER NARROW COVERAGE CURVILINEAR ARRAY INTRODUCING THE MILO 60 A variation on the popular MILO high-power curvilinear loudspeaker, the MILO 60 high-power narrow coverage curvilinear array loudspeaker excels where controlled narrow horizontal coverage is needed.
Operating Instructions Addendum: MILO 60 FLYING AND ARRAYING THE MILO 60 Standalone MILO 60 Arrays The MILO 60 loudspeaker shares the same dimensions and rigging components as the MILO to facilitate seamless integration, and uses the MG-3D/M multipurpose grid for flying. Since the MILO 60 is identical in size to the MILO, all of the standard MILO QuickFly hardware may be used.
Operating Instructions Addendum: MILO 60 Figure 3. Example configuration: combined MILO 60 (top three cabinets) and MILO array Figure 4.
Operating Instructions Addendum: MILO 60 USING SUBWOOFERS WITH THE MILO 60 MILO 60 with the M3D-Sub A MILO 60 system (or combined MILO 60/MILO/MILO 120 system) will provide full bandwidth frequency response down to 60 Hz. The height of the array (number of cabinets) will determine the total SPL available and how much low frequency energy can be provided, proportional to the upper-frequency spectrum.
Operating Instructions Addendum: MILO 60 MILO 60 with the 700-HP Subwoofer In applications where M3D-Sub features like directional low-frequency control are not needed, a MILO 60 array can be deployed in combination with Meyer Sound 700HP subwoofers. The 700-HP subwoofer extends the MILO system frequency response down to 30 Hz. Table 2 shows how you can integrate MILO (or combined MILO 60/MILO/MILO 120) arrays with 700-HP using the LD-3 line driver’s filtering capabilities to fine-tune the system.
Operating Instructions Addendum: MILO 60 6
Operating Instructions Addendum: MILO 60 APPENDIX A: MILO 60 SPECIFICATIONS ACOUSTICAL Note: The low-frequency power response of the system will increase according to the length of the array. Operating frequency range 60 Hz - 18 kHz Note: Recommended maximum operating frequency range. Response depends upon loading conditions and room acoustics. Free field frequency response 65 Hz - 17.
Operating Instructions Addendum: MILO 60 AUDIO INPUT Type Differential, electronically balanced Max.
Operating Instructions Addendum: MILO 60 PHYSICAL: MILO 120 Loudspeaker Enclosure Multi-ply hardwood Finish Black textured Protective grille Powder-coated hex stamped steel Rigging QuickFly MRF-MILO rigging frame, custom AlignaLink connectors and quick release pins Dimensions 54.00" w x 14.47" h x 22.00" d (1372 mm x 368 mm x 559 mm) Weight 235 lbs (106.
Operating Instructions Addendum: MILO 60 10
Meyer Sound Laboratories Inc. 2832 San Pablo Avenue Berkeley, CA 94702 www.meyersound.com T: +1 510 486.1166 F: +1 510 486.8356 © 2005 Meyer Sound Laboratories Inc. 05.132.095.
