Replacement Part List

INSTALLATION AND INSTRUCTIONAL MANUAL
xxxxx-xxx-xx month/day/year
PV SERIES
TM
MATERIAL:
SCALE
TITLE
DRAWING SIZE
D
DRAWING No:
LINDENWOOD ILLINOIS
WHERE USED
CADD FILENAME:
REF. DRAWING
DR BY
APPV BY
DATE
APPVBYDATEPIF#
REV
REVISION
NOTED)
(EXCEPT AS
DO NOT SCALE DRAWING
DATE
*********************
ProE Drawing
This drawing was
created in ProE.
The orginial drawing
should only be
edited in ProE.
*********************
20.000± .500
8.0 MIN
20.0 MAX
00002-562-00
DETAIL, ASSEMBLY
PV356 B&S
SHEET 2 OF 2
SEE TABLE ON SHEET 1
PV356
S:\00002\ 00002-562-00
D0000253300
0.100
JKG 5/19/2010
JKG 5/19/2010
TABD
PART WEIGHT
DETAIL, CHAIN TENSION
SCALE 0.250
DETAIL, CLUTCH ASSEMBLY
SCALE 0.250
CLUTCH
BLACK
WHITE FROM
ITEM #59
WHITE FROM ITEM #23
BLACK
24
86
ROUTE THREE WIRES THRU ITEM #35
CONNECT ALL FOUR GROUND WIRES (BETWEEN FLANGE NUTS, ON UNDERSIDE OF ENGINE PLATE) TO SAME SOLENOID MTG. BOLT
DETAIL, GROUND WIRING
SCALE .250
DETAIL, ACTUATOR &
THROTTLE ASSEMBLY
SCALE .250
DETAIL, WIRING ASSEMBLY,
SCALE .375
23
INSTALL PROTECTIVE CAP AFTER RUN TESTING SPREADER
BLUE
YELLOW (TO CENTER STUD ON SOLENOID)
RED
(REF) FUSE HOLDER W / 15A FUSE
36
33 20
RED
85 20
RED
GROUND
GREEN / BLACK
CONNECT TO THROTTLE ACTUATOR
BROWN
WHITE
4
CONNECT TO ENGINE KILL WIRE (NEAR SPARK PLUG)
CONNECT TO SOLENOID MTG. BOLT
66
35
(REF) SINGLE POLE WEATHER PACK CONNECTOR ITEMS #23 & #59
REMOVE 4" EXTENSION SUPPLIED WITH ITEM #23, AND DISCARD
BOTH SIDES OF CHAIN TAKEUP MUST BE ADJUSTED EVENLY
THROTTLE ACTUATOR ADJUSTMENT
1. LOOSEN THREE MOUNTING SCREWS AND NUTS ON THROTTLE ACTUATOR. 2. USING SPREADER CONTROL, MOVE THROTTLE TO FULL CHOKE POSITION (RABBIT). 3. SLIDE ACTUATOR IN CORRECT DIRECTION (TOWARDS HOPPER) UNTIL ENGINE LINKAGE HAS MOVED TO FULL CHOKE. DO NOT PUT EXCESSIVE FORCE ON LINKAGE ROD. 4. TIGHTEN THREE MOUNTING SCREWS AND NUTS. 5. TETS RUN ENGINE FOR FULL CHOKE ENGAGEMENT.
NOTES:
1. NEATLY SECURE ALL WIRING AWAY FROM ALL MOVING PARTS & HOT SURFACES. 2. APPLY DIEELECTRIC GREASE TO ALL ELECTRICAL CONNECTIONS. 3. DO NOT SECURE ANY WIRES TO FUEL LINE. 4. USE NYLON TIES (ITEM #71) TO "BUNDLE" WIRES FOR SELF SUPPORT. 5. THE SHORT YELLOW JUMPER WIRE ON ITEM #23 SHOULD NOT BE REMOVED. THIS IS THE REQUIRED CONNECTION FOR B&S. 6. THE SHORT BROWN JUMPER WIRE ON ITEM #23 SHOULD BE REMOVED AND REPLACED WITH ITEM #4.
DETAIL, PROP ROD
CLAMP ASSEMBLY
SCALE 1.125
40
63
INSIDE OF SHROUD
FINGERS OF ITEM #63 MUST BE COMPLETELY THRU ITEM #40
TOP OF SHROUD
DETAIL, CABLE CLAMP
SCALE .375
DETAIL, STARTER HARNESS
SCALE .500
CONNECT TO SOLENOID
CONNECT TO GROUND
85
86
88
87
5
PLUG SUPPLIED WITH ENGINE
RED
BLACK
PLUG SUPPLIED WITH ENGINE, CUT OFF END WITH THREE CONNECTORS & CONNECT TO ITEMS #5 AS SHOWN
79
71
28 29 37
ENGINE MOUNTING PLATE
(TOP VIEW)
REF. STARTER HARNESS
REF. STARTER HARNESS
23
83
29 29 80
28 29
36
68 69 70
67
44
65
POINT WHERE CHAIN CONTACTS FLANGE ON LONGITUDINAL
10
28
29
58
59
25
60
62
61
26
27
76
APPLY ANTI-SEIZE COMPOUND TO INPUT SHAFT BEFORE ASSEMBLING CLUTCH
BASE LINE PV SERIES