OPERATOR’S AND PARTS MANUAL NO. PB-SI-8720/8865 INDUSTRIAL SERIES TWIN EXPELLER SUPER SPREADER MODEL 8720 MODEL 8865 PATENTED U.S. PATENT NUMBER 5,368,236 5,501,404 DO NOT OPERATE EQUIPMENT UNTIL THIS MANUAL HAS BEEN READ AND UNDERSTOOD. MANUFACTURED BY Meyer Mfg. Corp. 574 West Center Avenue P.O. Box 405 Dorchester, Wisconsin 54425 Phone: 715-654-5132 • Fax: 715-654-5513 1-800-325-9103 E-mail: sales@meyermfg.com Website: www.meyermfg.
1. INTRODUCTION Congratulations on your purchase of a new Meyer farm equipment product. Undoubtedly you have given much consideration to your purchase and we’re proud that you have selected Meyer. Pride in craftsmanship, engineering and customer service has made Meyer products the finest in the farm equipment industry today. There is no substitute for quality. That is why thousands of people like you have purchased Meyer farm equipment.
PRE-DELIVERY & DELIVERY CHECK LIST Spreader Check List Meyer Manufacturing Corporation Phone: 715-654-5132 • Toll-Free: 1-800-325-9103 • P.O. Box 405 • Dorchester, WI 54425 This Pre-Delivery & Delivery Check List must be gone through by the Selling Party and the Customer to validate the Owner’s Registration Form. PRE-DELIVERY CHECK LIST DELIVERY CHECK LIST After the New Meyer Spreader has been completely set up, check to be certain it is in correct running order before delivering it to the customer.
Meyer Manufacturing Corporation 574 West Center Avenue Dorchester, WI 54425 Phone: 1-800-325-9103 Fax: 715-654-5513 Email: sales@meyermfg.com Website: www.meyermfg.
TABLE OF CONTENTS 1. INTRODUCTION ................................................................................................................................................... 2 1.1. How to Read Your Serial Number .................................................................................................................. 2 2. MANUFACTURER’S WARRANTY ........................................................................................................................ 7 3. SAFETY PRECAUTIONS ...
918-0408 (Standard 8720) (Optional 8865) (SN SI088720426 & Later) ......................................................... 30 918-0208 PTO Drive Shaft Assembly.............................................................................................................. 32 918-0310 (Optional 8720) (Standard 8865) (SN SI078720288-SI088720425) ............................................... 34 918-0410 (Optional 8720) (Standard 8865) (SN SI088720426 & Later) ...................................................
2. MANUFACTURER’S WARRANTY 11/2014 2014 MEYER INDUSTRIAL SPREADER I. The “Owner’s Registration Form” must be completed in full and promptly returned to Meyer Mfg. Corp. for this warranty to become both valid and effective. All warranties on new Meyer Industrial Spreaders shall apply only to the original retail customer from an authorized Meyer Mfg. Corp. dealership. II.
3. SAFETY PRECAUTIONS CAUTION: BEFORE ATTEMPTING TO OPERATE THIS SPREADER, READ AND STUDY THE FOLLOWING SAFETY INFORMATION. IN ADDITION, MAKE SURE THAT EVERY INDIVIDUAL WHO OPERATES OR WORKS WITH THE SPREADER, WHETHER FAMILY MEMBER OR EMPLOYEE, IS FAMILIAR WITH THESE SAFETY PRECAUTIONS. Require anyone who will operate this spreader to read and completely understand this Owner’s Manual.
4. SAFETY FIRST A brief definition of signal words that may be used in this manual is as follows: This symbol is used to call attention to instructions concerning personal safety. Be sure to observe and follow these instructions. Take time to be careful! DANGER indicates an imminently hazardous situation which, if not avoided, WILL result in serious injury or death.
The Meyer Super Spreader is manufactured with operator safety in mind. Located on the manure spreader are various safety signs to aid in operation and warn of danger or caution areas. Pay close attention to all safety signs on the spreader. DO NOT REMOVE ANY SAFETY SIGNS. IF SAFETY SIGNS ARE LOST, DAMAGED OR IF THE MANURE SPREADER HAS BEEN REPAINTED, REPLACE SAFETY SIGNS. REMEMBER: SAFETY SIGNS ARE FOR EVERYONE'S PROTECTION AND INFORMATION. SAFETY SIGN A. PART NO. 46-0001-5 SAFETY SIGN B. PART NO.
5. PRE-OPERATION WARNING: BEFORE OPERATING, READ THIS OWNER’S MANUAL COMPLETELY. PAY PARTICULAR ATTENTION TO THE “SAFETY PRECAUTION” AND “SAFETY FIRST” PAGES. READ ALL SAFETY MESSAGES HIGHLIGHTED BY “SAFETY ALERT SYMBOLS” THROUGHOUT THE MANUAL. WARNING: DO NOT OPERATE WITHOUT ALL SHIELDS, GUARDS AND COVERS INSTALLED. FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH. 5.1.
5.3. PRODUCT INSPECTION WARNING: INSPECT REGULARLY THAT ALL CONNECTIONS AND BOLTS ARE TIGHT AND SECURE BEFORE OPERATING. FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH. 5.3.1. WHEELS AND TIRES See page 82 for Wheel Torque and Tire Inflation Charts. Check for proper assembly and adjustment and make sure that all bolts are tightened. Securely retighten after a few hours of operation, as bolts can loosen up on new machinery. Check wheel lug nuts upon delivery and periodically thereafter.
Release the spring loaded collar. Be sure the pins fall into the groove of the tractor PTO shaft and that the collar snaps forward into the locked position. NOTICE: DO NOT USE A STEEL HAMMER TO AID IN JOINING PTO PARTS. Route hydraulic hoses through the hose support rod which is mounted to the hitch frame, Figure 3. Connect the hydraulic hoses for the flow control rear gate to the tractor’s double acting valve hydraulic system. Move the tractor hydraulic controls to observe proper flow gate operation.
5.5.2. PTO, ATTACHMENT OF The cutout clutch end of the PTO driveline must always be attached to the implement. The PTO driveline is equipped with a 1 3/8-6 spline on the implement half for attaching to the spreader. Remove the M17hexagon bolt from the splined hub and slide the PTO onto the implement splined input shaft. Install the hexagon bolt through the hub being sure the bolt is falling into the groove on the splined shaft. Torque tight using a metric size M17 6-point socket and torque down to 75 ft.
5.7.2.1. Truck Mounted Spreader Lights Depending on the make and model of the truck it may be necessary to install a light converter (MEYER PART #56-0028). Converter will allow signal lights and brake lights to operate according to DOT lighting standard. Call factory for more information. 5.7.3. MINIMUM TRACTOR WEIGHT Minimum Tractor Weight is calculated as 2/3 of the towing implement's gross weight (GW) Spreader Loaded Weight X .
6. OPERATION WARNING: SHUTOFF AND LOCKOUT POWER BEFORE CLEANING, ADJUSTING, LUBRICATING OR SERVICING THIS SPREADER. FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH. 6.1. LOADING CAUTION: DO NOT USE JACK EXCEPT WHEN SPREADER IS EMPTY. JACK WILL NOT SUPPORT ADDED WEIGHT. UNBALANCED WEIGHT MAY RESULT IN UNEXPECTED “TIP UP” OF SPREADER. IMPORTANT: OVERLOADING MAY CAUSE FAILURE OF AXLES, TIRES, STRUCTURAL MEMBERS, HITCHES, LOSS OF VEHICLE CONTROL, ETC. DO NOT EXCEED MAXIMUM NET LOAD.
MAXIMUM SPREADER LOAD WEIGHTS Model 2636 3245T 3954T Maximum Gross Weight (Pounds) 12,000 24,000 32,000 Total Net Weight (Pounds) 6,100 7,640 8,650 Cubic Foot Capacity** 181 227 272 Capacity in Gallons 1,355 1,694 2,033 8720T 46,645 11,445 468 3,500 8865T 56,140 18,140 562 4,200 **Struck capacity, heaped loads significantly increase weight. 6.2. UNLOADING DANGER: MAKE CERTAIN ALL PERSONNEL ARE CLEAR OF THE SPREADER AND THE ROTATING SPINNERS BEFORE APPLYING POWER.
6.2.1. SHEAR SPROCKET The Meyer Spreader you have received has been equipped with a shear sprocket design on the main auger drive sprockets. The augers are being driven by two Allen head grade 8 bolts. The design is such that if the bolts are sheared another set of holes to install new shear bolts will always be accessible without turning over the machine.
7. ADJUSTMENTS WARNING: SHUTOFF AND LOCKOUT POWER BEFORE CLEANING, ADJUSTING, LUBRICATING OR SERVICING THIS SPREADER. FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH. 7.1. FRONT DRIVE ROLLER CHAINS There are six roller chain drives located at the front of the spreader. Regularly check that all tensioning springs are in serviceable condition for automatic roller chain tightening. Manually adjust spring pensioners (as needed) by turning double locknuts on all tensioning bolt/idler assemblies.
The third chain drive is automatically tensioned by a spring-loaded nylon idler roller. The compression spring should be compressed to 4.5" in length. See Figure 8. To increase tension on the automatic tightener, tighten the adjuster bolt located at the left side of the spreader. FIGURE 8. THIRD CHAIN DRIVE The RH auger chain drive (Figure 9) is automatically tensioned by a spring loaded idler nylon roller. The compression spring should be compressed to 4.5" in length. See Figure 9.
The side shaft chain drive (PTO input shaft to the side line shaft drive sprocket, Figure 11) is automatically tensioned by a spring-loaded idler nylon roller. The extension spring should extend 2" from its neutral 5" total length. Manual adjustment for the automatic tensioning idler, nylon roller assembly is located at the right rear of the spreader’s front bearing mounting plate. FIGURE 11. SIDE SHAFT CHAIN DRIVE 7.2.
8. LUBRICATION WARNING: SHUTOFF AND LOCKOUT POWER BEFORE CLEANING, ADJUSTING, LUBRICATING OR SERVICING THIS SPREADER. FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH. 8.1. DAILY LUBRICATION (EVERY 8-12 LOADS) L1 Grease (2) rear spinner lower bearings. These bearings are grease line fitted to the LR frame channel of the spreader. L2 Oil (6) roller chain drives with automatic oiler at the front of spreader with clean 30-weight oil.
8.3. MONTHLY LUBRICATION L12 Maintain oil level in the corner gearbox at the centerline of the input shafts. Check regularly for any observable oil leakage. If oil leakage is excessive, replace required input/output shaft oil seals. Use ONLY EP #80-90 wt. gear lube oil or an equivalent in corner box, only Lighter weight gear lube oil may be used in temperatures lower than 20°F. Change oil in the gearboxes after the first season of use and regularly thereafter.
8.4.1.1. Prior To Use A. Using the CV Zerk (Key #2) place 20 pumps of grease into the CV center housing. This should be done with the driveline / CV as straight as possible. B. Slowly articulate the double joint through its maximum joint angle several times. C. Return the CV joint to its straight position and insert additional grease into the CV Zerk (Key #2) until grease is evident around the housing and center sliding disk. 8.4.1.2. Normal Operation A.
When replacing oiler brushes into brush holders, use regular 1/2"-20 nuts. Tighten nut finger tight initially as some adjustment may be needed later. For best results, place brush holders over top of roller chains and directly on top of sprockets. Adjust brush holders so oiler brushes are pushed down into the roller chain approximately 1/2". Carefully tighten up the 1/2"-20 nuts on the oiler brushes. DO NOT over tighten as damage to the brush will occur.
9. STORAGE AFTER USE WARNING: SHUTOFF AND LOCKOUT POWER BEFORE CLEANING, ADJUSTING, LUBRICATING OR SERVICING THIS SPREADER. FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH. DANGER: MAKE CERTAIN ALL PERSONNEL ARE CLEAR OF THE SPREADER AND THE ROTATING SPINNERS BEFORE APPLYING POWER. FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH. Before storing this spreader for an extended period of time perform the following: Allow the spreader to completely clean out the last load.
10. REPLACEMENT PARTS 10.1. INTRODUCTION WARNING: SHUTOFF AND LOCKOUT POWER BEFORE CLEANING, ADJUSTING, LUBRICATING OR SERVICING THIS SPREADER. FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH. WARNING: BEFORE SERVICING THIS PRODUCT, ENSURE THAT ALL PERSONNEL, INCLUDING FAMILY MEMBERS ARE FAMILIAR WITH THE SPREADER AND THE SAFETY HAZARDS THAT ARE PRESENT, ALONG WITH THE SAFETY PRACTICES THAT SHOULD BE OBSERVED WHILE WORKING ON THIS EQUIPMENT.
10.2. CRACKS The entire axle, o-beam, spindle and hitch should be visually inspected for cracks regularly. Any cracks found will indicate immediate repair or replacement is necessary. 10.3. WORN COMPONENTS Some parts will wear due to use. It is highly recommended to replace critical safety items such as a hitch that has worn through the "Wear Plate" or is less than three quarters of its original thickness. 10.4.
This Page Intentionally Blank.
918-0308 (STANDARD 8720) (OPTIONAL 8865) (SN SI078720288-SI088720425) (FOR EARLIER MODELS SEE PAGE 32) 918-0408 (STANDARD 8720) (OPTIONAL 8865) (SN SI088720426 & LATER) PTO DRIVE SHAFT-STAR PROFILE 1000 RPM 1-3/8 21 SPLINE WWE2480 (80° C.V.
918-0308 (STANDARD 8720) (OPTIONAL 8865) (SNSI078720288-SI088720425) (FOR EARLIER MODELS SEE PAGE 32) 918-0408 (STANDARD 8720) (OPTIONAL 8865) (SNSI088720426 & LATER) PTO DRIVE SHAFT-STAR PROFILE 1000 RPM 1-3/8 21 SPLINE WWE2480 (80° C.V.) (NEW GENERATION CLUTCH/HUB) KEY 1 2 3 4 5 PART NO.
918-0208 PTO DRIVE SHAFT ASSEMBLY 1000 RPM-21 SPLINE / 1-3/8” YOKE WWE2480 (80° C.V.) (OLD GENERATION CLUTCH/HUB) USED PRIOR TO SN SI078720287. FOR LATER MODELS SEE PAGE 30.
918-0208 PTO DRIVE SHAFT ASSEMBLY 1000 RPM-21 SPLINE / 1-3/8” YOKE WWE2480 (80° C.V.) (OLD GENERATION CLUTCH/HUB) KEY PART NO. DESCRIPTION Yoke 1-3/8"-21 Splined 1 918-0208-1-1 Assembly 2 918-0208-1-2 Grease Zerk in item 3 3 918-0208-1-3 Double Yoke 4 918-0208-1-4 Inboard Yoke 5 918-0208-1-5 Cross and Bearing Kit M8x1 67.
918-0310 (OPTIONAL 8720) (STANDARD 8865) (SN SI078720288-SI088720425) (FOR EARLIER MODELS SEE PAGE 38.) 918-0410 (OPTIONAL 8720) (STANDARD 8865) (SN SI088720426 & LATER) PTO DRIVE SHAFT-STAR PROFILE 1000 RPM 1-3/4 20 SPLINE WWE2480 (80° C.V.
918-0310 (OPTIONAL 8720) (STANDARD 8865) (SN SI078720288-SI088720425) (FOR EARLIER MODELS SEE PAGE 38) 918-0410 (OPTIONAL 8720) (STANDARD 8865) (SN SI088720426 & LATER) PTO DRIVE SHAFT-STAR PROFILE 1000 RPM 1-3/4 20 SPLINE WWE2480 (80° C.V.) (NEW GENERATION CLUTCH/HUB) KEY 1 2 3 4 5 5a 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 PART NO.
KEY 1 2 3 4 5 6 7 8 NS NS PART NO.
This Page Intentionally Blank.
918-0210 PTO DRIVE SHAFT ASSEMBLY 1000 RPM-20 SPLINE / 1-3/4” YOKE WWE2480 (80° C.V.) (OLD GENERATION CLUTCH/HUB) USED PRIOR TO SN SI078720287. FOR LATER MODELS SEE PAGE 34.
918-0210 PTO DRIVE SHAFT ASSEMBLY 1000 RPM-20 SPLINE / 1-3/4” YOKE WWE2480 (80° C.V.) (OLD GENERATION CLUTCH/HUB) KEY PART NO.
FIRST REDUCTION & SPINNER DRIVE Model 8720 / 8865 -40-
FIRST REDUCTION & SPINNER DRIVE KEY PART NO. DESCRIPTION 1 925-3720 Tightener Arm Assembly, Spinner Drive 2 3 933-3804 914-3602 914-3819 929-0003 910-0092 923-3756 Eyebolt, 5/16 x 5" / 4" Thread Length 1-1/2" 4-Bolt Bearing (Prior to SN SI088720425) 1-3/4" 4-Bolt Bearing (SN SI088720426 & Later) Extension Spring 80B15 Sprocket Side Shaft to Spinner Drive (Clamp Style) 8720 Front Side Shaft 81-3/4" Long 7 8 8A 8B 9 923-3754 914-3814 912-0013 912-0013-1 912-0013-2 808-.75-1.
FIRST REDUCTION & SPINNER DRIVE Model 8720 / 8865 -42-
FIRST REDUCTION & SPINNER DRIVE KEY PART NO. DESCRIPTION 910-0074 80B24 Split Sprocket 1-1/2" Bore,11 RPM Standard (Prior to SN SI088720425) 910-0121 910-0069 910-0122 910-0075 910-0123 910-0068 80B24 Split Sprocket 1-3/4" Bore,11 RPM Standard (SN SI088720426 & Later) 80B22 Split Sprocket 1-1/2" Bore,10 RPM (Prior to SN SI088720425) 80B22 Split Sprocket 1-3/4" Bore,10 RPM (SN SI088720426 & Later) 80B18 Split Sprocket 1-1/2" Bore 8.25 RPM (Prior to SN SI088720425) 80B18 Split Sprocket 1-3/4" Bore 8.
SECOND REDUCTION DRIVE Model 8720 / 8865 -44-
SECOND REDUCTION DRIVE KEY PART NO.
THIRD REDUCTION DRIVE Model 8720 / 8865 -46-
THIRD REDUCTION DRIVE KEY PART NO. 1 914-3811 910-3754-HD 2 910-3758 3 4 5 6 7 8 9 10 11 12 12A 12B 13 14 15 16 914-3825 911-0062 914-3807A-IND 914-3820A 914-3826 925-3783 925-3782 29-0009 925-3807-3 815-7510-Z 910-3753-HD 925-3779 912-0013 912-0013-1 912-0013-2 808-.75-1.
FINAL REDUCTION, RH AUGER DRIVE Model 8720 / 8865 -48-
FINAL REDUCTION, RH AUGER DRIVE KEY PART NO. 1 933-3701 910-0100 2 910-0100-1 910-0100-2 DESCRIPTION QTY 3" Retaining Ring 1 140B35 Shear Sprocket Assembly 1 Shear Hub & Plate Welded Assembly Only 1 Shear Hub Washer Only 1 9/16-18 x 1-3/4" Allen Head Cap Screw Grade 8 (Prior to SN 831-5618-1.75-SL AR SI088720/8865287) 2A 5/8-18 x 1-3/4" Allen Head Cap Screw Grade 8 (SN SI088720/8865287 & 831-6318-1.
FINAL REDUCTION, LH AUGER & THIRD AUGER DRIVE Model 8720 / 8865 -50-
FINAL REDUCTION, LH AUGER & THIRD AUGER DRIVE KEY PART NO.
BODY, SHIELDS & AUGERS - 8720 SPREADER Model 8720 / 8865 -52-
BODY, SHIELDS & AUGERS - 8720 SPREADER KEY PART NO. 901-3765 1 901-3769 2 926-3764 3 933-3703 4 913-3701 5 925-3770 926-3766 926-3701-2 926-3701-2-1 6 926-3750-3 926-3770-2 926-3771-1 926-3771-2 7 914-3812- NSM 8 914-3813 9L 926-3701-1 9R 10 926-3770-9 933-3701 926-3765 926-3701-2 926-3701-2-1 926-3750-3 926-3770-2 926-3770-1 926-3770-5 32-0027-1 SI-TNUK-KIT 925-3773 831-5013-1.
BODY, SHIELDS & AUGERS - 8720 SPREADER Model 8720 / 8865 -54-
BODY, SHIELDS & AUGERS - 8720 SPREADER KEY 30A 30B 30C 30D 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 65 66 67 68 69 70 71 PART NO. 956-3702-2 956-3702-1-1 956-3702-1-3 956-3702-1-2 33-0044 46-7000-1 925-3762 925-8720-1 955-3701 955-3803 955-3609 955-3760 955-3605 955-3756 955-3825 924-3762 924-3763 925-3750 925-3750-TR 901-8720 933-3632 929-3801 823-.
BODY, SHIELDS & AUGERS - 8865 SPREADER Model 8720 / 8865 -56-
BODY, SHIELDS & AUGERS - 8865 SPREADER KEY PART NO. 901-3765 1 901-3769 2 926-3760 3 933-3703 4 913-3701 5 925-3770 926-3772 926-3701-2 926-3701-2-1 6 926-3750-3 926-3770-2 926-3771-1 926-3771-2 7 914-3812- NSM 8 914-3813 9L 926-3701-1 9R 10 926-3770-9 933-3701 926-3773 926-3701-2 926-3701-2-1 11 926-3750-3 926-3770-2 926-3770-1 926-3770-5 12 32-0027-1 13 SI-TNUK-KIT 14 925-3773 14A 831-5013-1.
BODY, SHIELDS & AUGERS - 8865 SPREADER Model 8720 / 8865 -58-
BODY, SHIELDS & AUGERS - 8865 SPREADER KEY 30 30A 30B 30C 30D 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 65 66 67 68 69 70 71 PART NO. 956-3702-1 956-3702-2 956-3702-1-1 956-3702-1-3 956-3702-1-2 33-0044 46-7000-1 925-3762 925-3765 955-3701 955-3803 955-3609 955-3755 955-3605 955-3756 955-3825 924-3762 924-3763 925-3750 925-3750-TR 901-3751 933-3647 929-3801 823-.
REAR GATE & SHIELDS Model 8720 / 8865 -60-
REAR GATE & SHIELDS KEY 1 2 3 3A 4 5 6 6A 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 PART NO. 925-3759 925-3758-1 901-3778 901-3766-4 949-3750 901-3764-1 955-0011 955-0011-1 955-3802-2 955-3605 925-3754 955-3753 55-0092 924-3761 924-3750-2 924-3751 924-3750 33-1002 924-3760 32-0027-2 32-0027-3 955-3703 925-3760-1 925-3761-1 925-13804-1 925-13902 827-2528-.38 815-5013-Z 805-0050-Z 851-5013-3.
REAR GATE & SHIELDS Model 8720 / 8865 -62-
REAR GATE & SHIELDS KEY PART NO.
SPINNERS & GEARBOXES Model 8720 / 8865 -64-
SPINNERS & GEARBOXES KEY 1 1a 1b 1c 1d 2 3 4 5 7 8 9 10 11 12 13 14 15 16 17 18 19 20 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 PART NO. 901-13802 901-3753-3 901-3753-9 901-3753-5 901-3753-6 901-13801 901-3753-10 851-6311-2Z 815-6311-Z 933-3632 933-3639 901-3753-16 850-6311-1.5Z 814-6311-Z SI-8500-SAND-PAD 815-3824-Z 851-3824-1.5Z 19-0129 19-0130 19-0036 19-0035 808-1.75-2.5-14 937-0010-1 111-0060-18-CC 935-0001 937-0009-1 937-0009 937-0010 901-3753-15 850-6311-1.
SPINNER GEAR REDUCER - LEFT HAND (1:1) #19-0129 KEY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PART NO.
SPINNER GEAR REDUCER - CENTER (1:1) #19-0130 KEY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PART NO.
CORNER GEAR REDUCER - RIGHT HAND KEY 1000 RPM DRIVE PART NO. 19-0036 1 19-0031-1 2 19-0031-2 3 19-0036-1 4 19-0031-4 5 19-0029-5 6 19-0029-6 7 19-0029-7 8 19-0029-8 9 19-0029-9 10 19-0029-10 11 19-0029-11 12 19-0016-11 13 19-0016-5 14 19-0023-2 15 19-0002-17 16 19-0031-5 17 19-0029-16 Model 8720 / 8865 540 RPM DRIVE PART NO.
AXLE & WHEELS (STANDARD 8720) KEY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 16A 17 18 19 20 21 22 23 24 25 26 PART NO.
AXLE & WHEELS, HI-FLOAT PACKAGE (STANDARD 8865) (OPTIONAL 8720) Model 8720 / 8865 -70-
AXLE & WHEELS, HI-FLOAT PACKAGE (STANDARD 8865) (OPTIONAL 8720) KEY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 16a 17 18 19 20 21 22 23 24 25 26 PART NO. 75-0213 75-0213-2 75-0213-5 75-0213-10 75-0213-3 75-0213-6 75-0213-12 75-0213-13 75-0213-14 75-0213-7 75-0208-11 75-0208-12 75-0213-1 75-0213-8 75-0213-11 901-3771 75-0113 901-3770 901-3864-2 901-3773 881-6311-1.
HIGHWAY LIGHTS Model 8720 / 8865 -72-
HIGHWAY LIGHTS KEY 1 1A 2 2A 3 4 5 5A 5B 6 7 8 9 10 11A 11B 12 13 14 15 16 17 18 19 20 21 22 23 PART NO.
GEARBOX ATTACHMENT ASSEMBLY, TRUCK KEY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 PART NO. 19-0140 49-0032 618-0002 618-0005 619-0010-SYN 623-0020 625-8000-3 625-8000-4 910-0098 918-0223-1 925-8005-1 925-8005-2 925-8005-3 925-8005-4 935-0001 111-0060-18-CC 937-0010-1 625-8000-6 618-0002-1 918-0208-2-1 618-0005-1 618-0005-1-1 Model 8720 / 8865 DESCRIPTION Gearbox Drive Lower Gearbox 6" Hose Lower joint Assembly Keyed Upper Joint Assembly Splined 1.
19-0140 LOWER GEARBOX - TRUCK (SI-GBD PKG) USE 75W90 SYNTHETIC OIL ONLY CAPACITY 80-90 OUNCES. KEY 1 2 3 4 5 6 7 8 9 10 11 12 13 PART NO. 619-0010-1 619-0010-2 19-0140-1-ASSY 619-0010-4 19-0029-7 19-0029-8 19-0029-16 19-0029-9 19-0029-11 19-0016-11 19-0016-5 19-0024-17 19-0002-17 Model 8720 / 8865 DESCRIPTION Casting, Machined (Tapped Hole) 1.35:1 Casting, Machined (Thru Holes) 1.35:1 Pinion Shaft Gear w/ Bearings, Cups, Seal, Retaining Ring Assembly Cross Shaft gear Assembly 1.35:1 Bearing Cone 1.
619-0010-SYN UPPER GEARBOX - TRUCK (SI-GBD PKG) KEY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 PART NO. 619-0010-1 619-0010-2 619-0010-3 619-0010-4 19-0029-7 19-0029-8 19-0029-5 19-0029-6 19-0029-9 19-0029-11 19-0016-11 19-0016-5 19-0024-17 19-0002-17 19-0029-16 Model 8720 / 8865 DESCRIPTION Casting, Machined (Tapped Hole) 1.35:1 Casting, Machined (Thru Holes) 1.35:1 Pinion Shaft Gear Assembly 1.35:1 Cross Shaft gear Assembly 1.35:1 Bearing Cone 1.
This Page Intentionally Blank.
OIL-KIT See Page 24 for Oil Type and Oil Instructions Model 8720 / 8865 -78-
OIL-KIT KEY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 PART NO.
TRUCK MOUNT FENDERS KEY 1 2 3 4 5 6 7 PART NO.
MEYER INDUSTRIAL SPREADER TROUBLESHOOTING AUGERS FLOW CONTROL GATE GEAR BOXES SYMPTOM Augers shake or chatter PROBLEM Stiff roller chains - dry Loose roller chains Worn sprockets/chain Dry auger trough Augers wobble/lift up & Worn auger shaft bushings down Worn auger hold down nylon bearings Will not lift No hydraulic supply Froze tight w/build-up Will not close/seal Lodged foreign object/dirty Sticks/binds Dirty/dry slide guides Worn slide guides Worn out slide guide polyslick Clunking sounds Gears/bea
WHEEL TORQUE BOLT/STUD SIZE SOCKET SIZE PRESS FORMED WHEEL CENTER BOLT TYPE HEAVY DUTY WHEEL CENTER 3/4 1-1/8 / 1-1/2 NA Flange Nut 378 ft lbs 8720/8865 SPREADER W/BRAKES TIRE WHEEL TORQUE Clean adjoining surfaces Start nuts to bring wheel and brake drum flush to hub mounting surface. Avoid brake drum and/or wheel binding on hub. Install remaining wheel nuts. Torque to 50 ft-lbs. Then re-torque to 450-500 ft-lbs (22mm) or 378 ft-lbs (3/4”). Re-torque wheel nuts after 50-100 miles.
MEYER INDUSTRIAL SPREADER DIMENSIONS & SPECIFICATIONS CAPACITY Bushels Heaped Gallons/Cu.ft. (Struck) Cu. Yards. (struck) DIMENSIONS Overall Length Inside Tank Length Loading Height Overall Height -Top of Splash Guard Overall Width (std. Axle)Outside Tires Overall Width w/High Floatation axle pkg. Top Inside Tank Width SPECIFICATIONS Total Weight Maximum Load Net (Lbs.
MEYER INDUSTRIAL SPREADER DIMENSIONS & SPECIFICATIONS Frame Construction Door Opening Standard Axle Spindle Diameter High Floatation Axle Spindle Diameter Standard Axle Hub Size High Floatation Axle Hub Size Splash Shields-Standard Lights w/hookup cord Tractor Requirement PTO HP (Min.) OPTIONS 1000 RPM 1 3/8”-21 Spline 1000 RPM 1 3/4”-20 Spline Hydraulic Lid Poultry Litter Package High Floatation Axle Package Hyd. Brakes-HF axle only Safety Chain Truck Mount Drive Options Hyd.
NOTES ________________________________________________________ ________________________________________________________ ________________________________________________________ ________________________________________________________ ________________________________________________________ ________________________________________________________ ________________________________________________________ ________________________________________________________ _________________________________________________
NOTES ________________________________________________________ ________________________________________________________ ________________________________________________________ ________________________________________________________ ________________________________________________________ ________________________________________________________ ________________________________________________________ ________________________________________________________ _________________________________________________
MEYER INDUSTRIAL SPREADER MAINTENANCE RECORD Model No.____________________ Serial No.
Meyer Manufacturing Corporation 574 West Center Avenue Dorchester, WI 54425 Phone: 1-800-325-9103 Fax: 715-654-5513 Email: sales@meyermfg.com Website: www.meyermfg.
