OPERATORS AND PARTS MANUAL NO. 02-7-V-MAX V- MAX TWIN EXPELLER SUPER SPREADER MODELS: 2636 3245 3954 US PATENT NO. 5,368,236 5,501,404 DO NOT OPERATE EQUIPMENT UNTIL THIS MANUAL HAS BEEN READ AND UNDERSTOOD. Manufactured by County Hwy. A West P.O. Box 405 Dorchester, Wisconsin 54425 Phone 715-654-5132 • FAX 715-654-5513 1-800-325-9103 www.meyermfg.com E-mail: sales@meyermfg.
TABLE OF CONTENTS MANUFACTURER’S WARRANTY .........................................................................................................................3 INTRODUCTION.....................................................................................................................................................4 SAFETY PRECAUTIONS .......................................................................................................................................
NEW MEYER SUPER SPREADER Jan. 1, 1996 MANUFACTURER’S WARRANTY I. The “Product Registration & Inspection Certificate” along with the original billing invoice “Owners Registration Form” must be completed in full and promptly returned to Meyer Mfg. Corp. for this warranty to become both valid and effective. All warranties on New Meyer Super Spreaders shall apply only to the original retail customer from an authorized Meyer Mfg. Corp. dealership. II.
INTRODUCTION Congratulations on your purchase of a new Meyer farm equipment product. Undoubtedly you have given much consideration to your purchase and we’re proud that you have selected Meyer. Pride in craftsmanship, engineering and customer service have made Meyer products the finest in the farm equipment industry today. There is no substitute for quality. That is why thousands of people like you have purchased Meyer farm equipment.
SAFETY PRECAUTIONS This symbol is used to call attention to instructions concerning personal safety. Be sure to observe and follow these instructions. Take time to be careful! WARNING: BEFORE ATTEMPTING TO OPERATE THIS SPREADER, READ AND STUDY THE FOLLOWING SAFETY INFORMATION. IN ADDITION, MAKE SURE THAT EVERY INDIVIDUAL WHO OPERATES OR WORKS WITH THE SPREADER, WHETHER FAMILY MEMBER OR EMPLOYEE, IS FAMILIAR WITH THESE SAFETY PRECAUTIONS.
SAFETY FIRST A brief definition of signal words that are used in this manual is as follows: DANGER indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury. CAUTION indicates a potentially hazardous situation which, if not avoided, MAY result in minor or moderate injury. It is also used to alert against unsafe practices.
SAFETY FIRST The Meyer Super Spreader is manufactured with operator safety in mind. Located on the manure spreader are various decals to aid in operation and warn of danger or caution areas. Pay close attention to all decals on the spreader. DO NOT REMOVE ANY DECALS. IF DECALS ARE LOST, DAMAGED OR IF MANURE SPREADER IS REPAINTED, REPLACE DECALS. REMEMBER: DECALS ARE FOR YOUR PROTECTION AND INFORMATION.
PRE-OPERATION WARNING: BEFORE OPERATING, READ THIS OWNERS MANUAL COMPLETELY. PAY PARTICULAR ATTENTION TO THE “SAFETY PRECAUTIONS” AND “SAFETY FIRST” PAGES. READ ALL SAFETY MESSAGES HIGHLIGHTED BY “SAFETY ALERT SYMBOLS” THROUGHOUT THE MANUAL. This spreader is to be operated with 540 RPM PTO only, unless the spreader is 1000 RPM equipped. The hitch of the spreader is designed for a standard tractor drawbar. Adjust the drawbar at 13 to 17 inches above the ground.
Manually latch/close the trip pan doors, figure 4. HYDRAULIC HOSES Check that the flow control rear gate is completely closed. It is unlawful to allow slurry to splash or leak onto public roads. HOSE BRACKET TRANSPORTING PTO SHAFT TRACTOR TOWING SIZE REQUIREMENTS Use the following chart for calculating the minimum tractor weight.
USE OF SAFETY CHAIN FREEZING WEATHER OPERATION CAUTION: A SAFETY CHAIN MUST BE INSTALLED TO RETAIN THE CONNECTION BETWEEN TRACTOR (OR OTHER TOWING VEHICLE) AND SPREADER WHENEVER TRAVELING ON PUBLIC ROADS IN CASE THE HITCH CONNECTION WOULD SEPARATE. A SUGGESTED ATTACHMENT IS ILLUSTRATED ON FIGURE 3. Allow spreader to completely empty last of manure contents and disengage tractor PTO. Shut off tractor, remove the ignition key and allow all movement to stop before attempting to clean the spreader.
trip pan doors, ends of augers, flow control rear gate and spinners. Manually close the trip pan doors. WARNING: MAKE CERTAIN EVERYONE IS CLEAR OF THE SPREADER BEFORE APPLYING POWER. FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH. Slowly engage the PTO. Operate the spreader several minutes to clean manure scrapings and to allow any remaining manure and the spreader to freeze dry. Hydraulically run the flow control rear gate up and down to clean gate slide guides.
OPERATION LOADING UNLOADING CAUTION: TO PREVENT DAMAGE TO AUGERS, SPINNERS, AND DRIVE LINES, FOREIGN OBJECTS (STONES, CONCRETE, TIMBER, METAL OR LARGE FROZEN CHUNKS OF MANURE) SHOULD NEVER BE LOADED INTO THE SPREADER. WARNING: MAKE CERTAIN EVERYONE IS CLEAR OF SPREADER BEFORE APPLYING POWER. FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH. DANGER: NEVER ENTER THE SPREADER BOX FOR ANY REASON WITHOUT FIRST DISCONNECTING PTO SHAFT FROM TRACTOR. DO NOT ALLOW OTHERS IN THE BOX.
VERY IMPORTANT: THIS MACHINE IS NOT INTENDED TO BE A BALE GRINDER, HAY CHOPPER OR BEDDING MACHINE. LONG HAY OR STRAW MUST CONTAIN MANURE IN ORDER TO BE SPREAD. FAILURE TO COMPLY MAY DAMAGE THE DRIVETRAIN AND VOID THE WARRANTY. RESULT IN SPREADER DAMAGE OR SERIOUS PERSONAL INJURY. The rear spinners have been designed and tested to provide the best spread pattern for most liquids and semi solid manure. However, the pattern will vary for each specific condition.
the remainder of the load. If both sides do shear install only one set of auger shear bolts and unload one side at a time. After first side is unloaded install bolts in opposite side and unload the remainder of the spreader. If a second shear has happened without obstruction in the auger, install the next larger size shear bolt. As the shear bolt size is increased the protection on the machine is going to decrease. The potential for equipment damage is greater.
PTO DRIVE LINE WARNING: BEFORE ATTEMPTING TO OPERATE THIS SPREADER, READ AND STUDY ALL SAFETY INFORMATION. IN ADDITION, MAKE SURE THAT EVERY INDIVIDUAL WHO OPERATES OR WORKS WITH THE SPREADER, WHETHER FAMILY MEMBER OR EMPLOYEE, IS FAMILIAR WITH THESE SAFETY PRECAUTIONS. WARNING: DISCONNECT PTO DRIVE SHAFT AND HYDRAULIC HOSES (RELIEVE HYDRAULIC PRESSURE) BEFORE CLEANING, ADJUSTING, LUBRICATING OR SERVICING THIS SPREADER. FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH.
3. Adjust the drawbar at 13-17” above the ground. Extend or shorten the drawbar so horizontal distance from end of tractor PTO shaft to center of hitch pin hole is 14” for 540 RPM 1-3/8-6 spline, (16” for optional 1000 RPM 1-3/8-21 spline). Secure the drawbar so the hitch pin hole is located directly below the PTO drive line. PTO adapters are not recommended as damage to the drive line may occur. A hitch pin with a minimum diameter of 1” and bottom retaining pin is recommended.
ADJUSTMENTS WARNING: DISCONNECT PTO DRIVE SHAFT AND HYDRAULIC HOSES (RELIEVE HYDRAULIC PRESSURE) BEFORE CLEANING, ADJUSTING, LUBRICATING OR SERVICING THIS SPREADER. FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH. SPINNER MATERIAL GUIDES Regularly inspect and adjust two spinner material guides located at both the LR and RR of the spreader. Create a 1/8-3/8” clearance between material guides and spinner teeth, figure 8. Maintain the recommended clearances for maximum spreading pattern.
WARNING: DISCONNECT PTO DRIVE SHAFT AND HYDRAULIC HOSES (RELIEVE HYDRAULIC PRESSURE) BEFORE CLEANING, ADJUSTING, LUBRICATING OR SERVICING THIS SPREADER. FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH. FRONT DRIVE ROLLER CHAINS There are five roller chain drives located at the front of the spreader. Regularly check that all tensioning springs are in serviceable condition for automatic roller chain tightening.
IDLER NYLON ROLLER SPRING LOADED ADJUSTER RH AUGER SPROCKET The RH auger chain drive, figure 11, is automatically tensioned by a spring loaded idler NYLON roller. The extension spring should extend 3/4" from its neutral 4" total length. Manual adjustment for the automatic tensioning idler, NYLON roller assembly is located at the right front lower corner of the spreader tank. ROLLER CHAIN FIGURE 11.
LUBRICATION WARNING: DISCONNECT PTO DRIVE SHAFT AND HYDRAULIC HOSES (RELIEVE HYDRAULIC PRESSURE) BEFORE CLEANING, ADJUSTING, LUBRICATING OR SERVICING THIS MACHINE. FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH. DAILY LUBRICATION (every 8-12 loads) Grease (2) rear spinner lower bearings. These bearings are grease line fitted to the LR frame channel of the spreader. Oil (5) roller chain drives regularly at the front of spreader with light weight machine oil.
MONTHLY LUBRICATION Keep the (3) gearboxes ½ full of liquid gear grease at all times, capacity approximately 30 oz. Check regularly for any observable leakage. If leakage is excessive, replace required input/output shaft seals as needed. Lubricate with a “Semi-Fluid, EP Lithium Base, Gear Grease”. Clean and repack the wheel hubs with axle grease annually. Grease hub through zerk in hub monthly. Be careful not to over grease and force seal out of back side of hub.
LUBRICATION & ADJUSTMENT FOR OPTIONAL 3RD AUGER WARNING: DISCONNECT PTO DRIVE SHAFT AND HYDRAULIC HOSES (RELIEVE HYDRAULIC PRESSURE) BEFORE CLEANING, ADJUSTING, LUBRICATING OR SERVICING THIS MACHINE. FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OF DEATH. COVER WEEKLY LUBRICATION (every 25-30 loads) ) Grease (1) bearing supporting the front shaft of the 3rd auger assembly. This bearing is grease line fitted to the spreader front, bearing back plate.
INSTRUCTIONS FOR OPTIONAL AUTOMATIC CHAIN OILER WARNING: DISCONNECT PTO DRIVE SHAFT AND HYDRAULIC HOSES (RELIEVE HYDRAULIC PRESSURE) BEFORE CLEANING, ADJUSTING, LUBRICATING OR SERVICING THIS SPREADER. FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH. The automatic chain oiler attachment gives a squirt of clean oil to all roller chains every time that the spreaders rear gate, hydraulic cylinder is activated.
REPAIR PARTS OPTIONAL OIL-KIT 35 Model V-Max —24—
OPTIONAL OIL-KIT KEY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 PART NO.
FRONT SHIELD & SIDE SHAFT DRIVE Model V-Max —26—
FRONT SHIELD & SIDE SHAFT DRIVE KEY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 22a 23 24 25 PART NO. 914-3801 910-0013 935-0002 923-3828 923-3829 923-3830 925-3882 46-3600-12 46-3600-14 33-0044 912-0001 925-3882-1 911-0035 808-150-300-10 910-0015 808-1.5-2.25-10 813-3118-Z 808-1-1.5-18 933-3804 925-3822-6 929-0003 38-0013 955-3703 925-5006-1 924-3821 924-3827 32-0018-1 924-3826 924-3820 808-1.25-1.
AUGER DRIVE, PRIMARY REDUCTION KEY PART NO. 1 933-3628 KEY PART NO. 9 914-3602 2 3 10 11 12 13 925-3606 925-3883 931-3810 923-3833 923-3833-XL 14 910-0063 15 16 17 813-3118-Z 933-3804 925-3822-6 18 19 20 21 929-0003 808-1-1.5-18 35-0010 933-3632 22 935-0001 4 5 5A 5B 6 7 8 DESCRIPTION Copper Tube Grease Line 25" (includes zerk, fittings) 38-0013 Roll Pin, 5/16" x 1-3/4" 925-3883-1 First Reduction Tightener Assembly Arm Weldment 808-.75-1.
AUGER DRIVE, SECONDARY REDUCTION KEY 1 2 3 4 5 6 6A 6B 7 8 9 10 11 12 13 14 15 16 17 18 Model V-Max PART NO. 14-0031 38-0013 910-0063 851-7510-3Z 911-0018 912-0013 912-0013-1 912-0013-2 808-.75-1.25-14 925-3884-1 813-3118-Z 933-3804 925-3822-6 929-0003 808-1-1.
RH AUGER DRIVE, FINAL REDUCTION Install (#120-56) Roller Chain, Key #13 W/Connector Link Cotter Pins Facing Towards Front Of Spreader.
RH AUGER DRIVE, FINAL REDUCTION KEY 1 2 3 4 5 6 7 8 9 10 10A 10B 11 12 13 14 15 16 17 18 19 PART NO. 33-0025 910-0064 910-0028 910-0101 831-5020-1.75 884-5020 831-5618-1.75 884-5618 813-3118-Z 933-3804 913-3801-1 925-3834 933-3621 808-.75-1.25-14 912-0013 912-0013-1 912-0013-2 925-3848-7 929-3601 911-0023 851-7510-3.
LH AUGER DRIVE, FINAL REDUCTION Install (#120-72) Roller Chain, Key #21 W/Connector Link Cotter Pins Facing Towards Rear Of Spreader.
LH AUGER DRIVE, FINAL REDUCTION KEY 1 2 3 4 7 8 9 10 11 12 13 14 15 16 17 18 19 20 20A 20B 21 21A 22 23 24 25 27 28 29 30 31 32 33 34 35 36 37 Model V-Max PART NO. 14-0031 925-3873 910-0064 808-.75-1.25-14 925-3846-2 851-7510-6Z 925-3870-1 914-3807A 925-3833 913-3801-1 813-7510-Z 933-3621 925-3841 29-0009 925-3885-1 925-3843 925-3839 912-0014 912-0014-1 912-0014-2 911-0024 911-0026 912-0001 925-3838 925-3842 910-0028 910-0101 831-5020-1.75 884-5020 831-5618-1.75 884-5618 33-0025 925-3807-3 851-5013-1.
BOX, AUGERS & SIDE SHAFT Model V-Max —34—
BOX, AUGERS & SIDE SHAFT KEY 1 2 3 3A 4 5 6 7 9 10 PART NO.
UNLOADING GATE & TRIP PAN DOORS Prior to 08 Serial Nos.
UNLOADING GATE & TRIP PAN DOORS KEY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 Model V-Max PART NO.
SPINNERS & GEARBOX SHAFT DRIVE PRIOR TO 08 SERIAL NOS.
SPINNERS & GEARBOX SHAFT DRIVE KEY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 PART NO. 901-3834-1 901-3835-1 19-0041 935-0002 937-0014-1 19-0042 19-0043 901-3856-1 901-3897-1 901-3855-1 901-3896-1 914-3604 901-3855-8 924-3817 924-5011 924-3818 937-0009-2 937-0009-3 808-1.38-2.5-14 808-1.38-2.5-18 808-1.38-2.5-10 901-3855-4 851-5013-1.
SPINNER GEAR REDUCERS USE FLUID GEAR GREASE ONLY. DO NOT USE GREASE FOR LUBRICANT. Model V-Max KEY 1 2 3 4 5 8 9 10 11 12 13 PART NO.
HUBS, AXLE & TANDEM AXLE ASSEMBLY KEY PART NO. M 3954 PART NO. M 2636&3245 75-0207 75-0205 75-0207-2 75-0205-2 75-0207-3 75-0205-3 75-0207-4 75-0205-4 75-0202-4 75-0202-4 75-0202-3 75-0202-3 75-0205-7 75-0205-7 75-0205-8 75-0205-8 75-0205-9 75-0205-9 75-0205-10 75-0205-10 75-0205-11 75-0205-11 75-0207-12 75-0205-12 75-0207-1 75-0205-1 30-0008 30-0008 30-0009 30-0009 30-0006 30-0006 901-3860-4 901-3860-4 881-5013-5.5 881-5013-5.5 814-5013-Z 814-5013-Z NA 901-3863 DESCRIPTION KEY PART NO.
OPTIONAL THIRD AUGER Items 10 and 11 are used on two auger units only.
OPTIONAL THIRD AUGER KEY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 23A 24 Model V-Max PART NO. 929-3601 35-0008 910-0050 14-0031 925-3866 911-0033 35-0010 910-0005 925-3861 925-3860 925-3863 933-3606 913-3805 925-3865 933-3630 926-3819 926-3820 926-3821 933-3804 925-3825 813-3118-Z 851-6311-2Z 814-6311-Z 955-3809 901-3862 901-3862-1 901-3832-2 DESCRIPTION Extension Spring ½"x1/2"x2" Square Key 80B 26 2"B, ½" Keyway Bearing, 4-Bolt Flange, 2" B Chain Tightener Bracket Wldmt.
918-0212 PTO DRIVE SHAFT ASSEMBLY (PRIOR TO SERIAL #SV083954451) 918-0312 PTO DRIVE SHAFT ASSEMBLY (SERIAL #SV083954451 & LATER) 540 RPM 1-3/8 – 6 SPLINE YOKE WWE2480 (80 DEGREE C.V.) KEY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 MEYER PART NO.
(PRIOR TO SERIAL #SV083954451) 540 RPM 1-3/8 – 6 SPLINE YOKE WWE2480 (80 DEGREE C.V.) KEY 1 2 3 4 5 6 7 8 NS NS MEYER PART NO. 918-0208-2-3-2 918-0208-2-3-3 918-0208-2-3-4 918-0208-2-3-5 918-0208-2-3-6 918-0208-2-3-7 918-0208-2-3-1 918-0208-2-3-8 918-0208-2-3-9 918-0208-2-3-11 DESCRIPTION Housing Hub Spring Pack 1900NM Washer Retaining Ring Sealing Ring Clamp Cone Assembly Cam Bushing-In Item #2 Shim Kit (SERIAL #SV083954451 & LATER) 540 RPM 1-3/8 – 6 SPLINE YOKE WWE2480 (80 DEGREE C.V.
(08 SERIAL # AND LATER) 918-0309 PTO DRIVE SHAFT ASSEMBLY 1000 RPM-1-3/8”, 21 SPLINE SP (STANDARD) 918-0311 PTO DRIVE SHAFT ASSEMBLY 1000 RPM 1-3/4”, 20 SPLINE (OPTIONAL) WWE2480 (80 DEGREE C.V.) NOTE: PTO IS 4” SHORTER (1-3/4x20) 6” SHORTER (1-3/8x21) THAN STANDARD 540 OR 1000 RPM PTO KEY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 MEYER PART NO.
918-0309 PTO DRIVE SHAFT ASSEMBLY 1000 RPM-1-3/8”, 21 SPLINE SP (STANDARD) 918-0311 PTO Drive Shaft Assembly 1000 RPM 1-3/4”, 20 SPLINE (OPTIONAL) CUTOUT CLUTCH KEY 1 2 3 4 5 6 7 8 NS NS MEYER PART NO.
PRIOR TO 08 SERIAL NOS. 918-0209 PTO DRIVE SHAFT ASSEMBLY 1000 RPM 1-3/8” 21 SPLINE (STANDARD) 918-0211 PTO DRIVE SHAFT 1000 RPM 1-3/4” 20 SPLINE (OPTIONAL) WWE2480 (80 DEGREE C.V.) NOTE: PTO IS 4" SHORTER THEN STANDARD 540 OR 1000 RPM PTO KEY MEYER PART NO.
PRIOR TO 08 SERIAL NOS. 918-0209 PTO DRIVE SHAFT ASSEMBLY 1000 RPM 1-3/8” 21 SPLINE (STANDARD) 918-0211 PTO DRIVE SHAFT 1000 RPM 1-3/4” 20 SPLINE (OPTIONAL) WWE2480 (80 DEGREE C.V.) KEY 1 2 3 4 5 6 7 8 NS NS Model V-Max MEYER PART NO.
1000 RPM KIT SVS-RPM-KIT KEY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 NS NS NS PART NO. 19-0002-17 29-0015 33-0012 33-0021 33-0039 935-0003 805-0031-Z 806-0031-Z 851-3118-.75Z 910-0005 911-0045-HD 912-0010 914-3809 914-3816 914-3817 923-3834 923-3835 925-3890-1 925-3891-1 925-3892-10 925-3892-1 925-3892-9 933-3812 955-3809 808-1.5-2.
V-MAX HIGHWAY LIGHTING 15 KEY PART NO. 3 56-0003 KEY PART NO.
MEYER SUPER SPREADER “TROUBLE SHOOTING” SYMPTOM AUGERS Augers shake or chatter PROBLEM Stiff roller chains - dry Loose roller chains Worn sprockets/chains Dry auger trough SOLUTION Lubricate roller chains Tighten roller chains Replace sprockets/chains Load auger trough w/manure Augers wobble/lift up & down Wor n auger shaft bushings Replace auger shaft bushings Worn auger hold down nylon Replace auger hold down bearings nylon bearings FLOW CONTROL GATE GEAR BOXES Will not lift No hydraulic supply Fr
MEYER SUPER SPREADER “TROUBLE SHOOTING” SYMPTOM ROLLER CHAINS AND SPROCKETS PROBLEM Excessive chain wear Lack of lubrication Out of alignment/loose Lubricate/align/tighten Roller chain breakage Loose roller chain Worn sprockets Tighten roller chains Replace sprockets Sprocket teeth tipped over Worn roller chain Bad roller bearings SPINNERS (PADDLES/TEETH) SOLUTION Replace roller chain Replace bearings Spinners turn hard/squeak Bad lower spinner bearings Replace lower spinner bearings Shake at hi
MEYER SUPER SPREADER “MAINTENANCE RECORD” Model No. ____________________Serial No.
MEYER EQUIPMENT WHEEL TORQUE BOLT/STUD SIZE ½ 9/16 5/8 3/4 SOCKET SIZE 3/4 7/8 15/16 1-1/16 1-1/8 / 1-1/2 PRESS FORMED WHEEL CENTER 80 ft lbs 80 ft lbs 100 ft lbs BOLT TYPE Lug Bolt Lug Bolt Bevel or Flange Nut Flange Nut HEAVY DUTY WHEEL CENTER 85 ft lbs 120 ft lbs 160 ft lbs TIRE INFLATION TIRE SIZE 11L-15 12.5L-15 12.5L-15 14L-16 16.5L-16 19LX16.1 21.5L-16.1 11R/22.5 425/65X22.
Farm Equipment Buyers Trust the Name Meyer! MEYER SUPER SPREADER “SPECIFICATIONS” Bushels Model 2636 Model 3245 Model 3954 260(no ht. ext.) 360(with ht. ext.) 320(no ht. ext.) 450(with ht. ext.) 390(no ht. ext.) 540(with ht. ext.) Gallon 1355 1745 1694 2189 2033 2617 Cubic Foot 181 233 227 292 272 350 5300 lbs. 5665 lbs. 6601 lbs. 7020 lbs. 7630 lbs. 8100 lbs. Weight Overall Height with 14L tire (add 1-1/2 inches for 16.5L tire) Tank Length 58-1/2" (no ht. ext.
Model V-Max —57—
Model V-Max —58—
Model V-Max —59—
E