11RT

Figures

figure description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page

1-1: Tower Configuration with Power Module, Battery Module,

and optional Transformer Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 — 4

1-2: Rack Configuration with Power Module, Battery Module,

and optional Transformer Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 — 5

1-3: Rear panel of the Power Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 — 6

1-4: Rear Panel of the Battery Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 — 6

1-5: Rear Panel of the optional Transformer Module. (PN 86211) . . . . . . . . .1 — 7

1-6: View of typical control panel interface. . . . . . . . . . . . . . . . . . . . . . . . . . . .1 — 7

1-7: Power Module Rail Kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 — 8

1-8: Battery/Transformer/CLA Module Rail Kit. . . . . . . . . . . . . . . . . . . . . . . . .1 — 8

1-9: Typical back-up time with multiple EXB’s at full load. . . . . . . . . . . . . . . .1 — 9

1-10: Typical Battery Integration kit with casters setup. . . . . . . . . . . . . . . . . .1 — 10

1-11: Typical Transformer Module contents and connections. . . . . . . . . . . . .1 — 11

1-12: CLA Module Contents and Connections. . . . . . . . . . . . . . . . . . . . . . . . .1 — 12

2-1: Contents of EX 5/7/11RT Power Module. . . . . . . . . . . . . . . . . . . . . . . . .2 — 2

2-2: Contents of EXB 5/7/11RT Battery Module. . . . . . . . . . . . . . . . . . . . . . . .2 — 3

2-3: Tower Configuration of Standard System and

Optional Transformer Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 — 5

2-4: Typical orientation of the logo and control panel.

(Power Module shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 — 6

2-5: Accessing Battery Pack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 — 6

2-6: Rack mounting of the Power Module onto the rails. . . . . . . . . . . . . . . . .2 — 7

2-7: Input/Output Box Bracket System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 — 8

2-8: RS232 Communication Cable Connection. . . . . . . . . . . . . . . . . . . . . . . .2 — 9

2-9: Relay Pin Connections for Communication Port. . . . . . . . . . . . . . . . . . .2 — 10

2-10: Communication Card Slot with Network

Management Card installed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 — 10

2-10a: Activation of Remote Emergency Power Off function

using a contact normally open switch. . . . . . . . . . . . . . . . . . . . . . . . . . .2 — 12

2-10b: Activation of Remote Emergency Power Off using a

contact normally closed switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 — 12

2-11: Power Module I/O Box Terminal Block Diagram. . . . . . . . . . . . . . . . . . .2 — 13

2-12: Normal AC Input and Output Cables installation. . . . . . . . . . . . . . . . . . .2 — 14

2-13: View of EX RT Transformer Module connected downstream

for 120/208/240 Vac outputs (shown with one EXB). . . . . . . . . . . . . . . .2 — 15

2-14: Normal AC Input, Bypass AC, and Output Cables Installation,

and Simplified Connection Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . .2 — 16

2-15: Accessing Terminal Blocks for Input and Output power cables. . . . . . .2 — 17

2-16: Rear view of Battery Module cable connections. . . . . . . . . . . . . . . . . . .2 — 18

2-17: Rear view of CLA Module cable battery and AC input connections . . . .2 — 19

EX 5/7/11RT Systems

Contentsc iv 86-86000-00 B00