TWPro T W I N W A L L I N S U L AT E D C H I M N E Y IGNITE YOUR AMBITION
Contents Description Page Welcome 3 Key Benefits 4 Installing TWPro 5 Product place guides 6-9 Adaptors 12 Starter Pipes Straight Pipes Elbows & Tees Supports Fire Stops Flashings Finishing Plates Terminals Accessories Offset Data Support Data 2 | TWPro
Welcome to Mi-Flues MI-Flues is a Blackpool based company with factories and distribution centres across England, Scotland and Ireland, and are dedicated to the development of the highest quality flues and chimney products. Established in 1996, MI-Flues has grown to become one of the most respected manufacturers of chimney products in the industry, constantly pushing the boundaries of products specification and design, this has led to the introduction of the TWPro family of flue products.
KEY BENEFITS TWPro is a high quality, multi-fuel, stainless steel twin wall chimney system designed for use with all solid fuel, wood, coal, gas, oil and pellet heating appliances. It is tested to a maximum operating temperature of 600°C and comes with a 25 year warranty. TWPro has exceptional thermal properties which have allowed it to be classified as G50. The 50mm clearance required to combustible materials also applies when it is installed in an enclosure.
INSTALLATION & DESIGN CONSIDERATIONS When designing the flue system the following points should be considered:1. The internal diameter of the flue system should not be less than the size specified by the appliance manufacturer. 2. Ensure that the flue pipe connection from the appliance rises vertically for at least 600mm before any change of direction is contemplated. 3. The minimum height for any solid fuel flue system is recommended to be 4.5m from the top of the appliance. 4.
Anti-Wind Cowl 2-***-091 The cowl prevents unwanted rain penetrating the chimney, it is also designed to help with down draughts. Wall Band 15-**-051 Provides lateral strength to the chimney, should be used every 2.5m. 45° Elbow 2-***-031 45° Elbows help create an offset to get round the gutter / overhang. Finishing Plate Round 45° 2-***-107 Fixed to the internal wall will cover any damage made to the wall.
EXTERNAL 1000mm Pipe 2-***-010 A fixed one metre length of TWPro twin wall insulated pipe. Long 135° Tee 2-***-044 The Long 135° Tee has an extra long branch that will reach through most standard UK wall constructions. Base Support Plate 2-***-060 Used to provide vertical support at the base of the external flue. Tee Cap 2-***-037 Attached to the bottom of the external flue allows for easy sweeping.
CHIMNEY LOWERED OR REMOVED FLEX RELINING AND WITH CHIMNEY BEING LOWERED Residential Flashing EPDM 12-201RES Used to seal the roof where the flue has penetrated it. TWPro Black Adjustable Connecting Pipe 1000mm 30-***-025 Connects TWPro to Enamel Pipe, also allows the stove to be disconnected from the chimney at this point.
Storm Collar 15-***-082 Used to ensure water tightness when passing through the roof. It protects the flashing from extreme weather conditions and UV. HOUSE INTERNAL Roof Support 15-***-067 Attaches to the rafters in the roof space to help support the chimney. Loft Mesh Kit 13-MESHKIT-*** Building Control requirement means that the chimney must not be exposed in a usable loft space.
Introducing the new Y WA The TWPro range of flue products carries a 25 year warranty which covers manufacturing defects. Provided that the system has been correctly installed and used as per the installation instructions. As with all chimney systems W AR AN it is imperative the flue is R swept on an annual basis by an approved chimney sweep and a signed record of this is maintained.
TWPro colour range PRODUCT IDENTIFIER KEY Colour option not available Product Name Description Code Diameter Product Image Flat Adaptor to Single Wall Ø 125 Ø 150 Ø 175 Ø 200 Ø 250 Ø 300 2-125-005 30-125-005 2-150-005 30-150-005 10-175-005 50-175-005 10-200-005 50-200-005 - - - - 17-125-005 17-150-005 - - - - - - 14-125-005 14-150-005 - - - - Colours White Ø 100 10-100-005 50-100-005 Grey Ø 80 10-80-005 - Black m Stainless Steel Universal adaptor to connect the a
ADAPTORS Single Wall to Twin Wall Adaptor Universal adaptor to connect the appliance outlet to the TWPro, can also connect single wall connecting flue or vitreous enamel to TWPro. This has a tapered design to allow a smooth transition from single wall to twin wall.
ADAPTORS Flat Adaptor to Single Wall Universal adaptor to connect the appliance outlet to the TWPro, can also connect single wall connecting flue or vitreous enamel to TWPro. This has a flat design to give an instant transition from the appliance or connecting flue to TWPro in the shortest length.
STARTER PIPES Starter Length 1000mm All in one pipe with built in single wall adaptor, designed to give a more aesthetic clean look when coming directly of the top of an appliance.
STARTER PIPES Adjustable Connecting Pipe 1000mm 1000m pipe with an exposed telescopic connecting pipe built into the male end. This has a cover band and insulation to cover the connecting pipe. This can be used to connect directly on to a heating appliance and allows a clean streamlined finish to a stove installation. The disconnecter section allows for easy removal of the appliance.
STRAIGHT PIPES Pipe 1000mm Rigid fixed 1000MM pipe effective lengths.
STRAIGHT PIPES Pipe 100mm Rigid fixed 100MM pipe effective lengths m Ø 80 Ø 100 Ø 125 Ø 150 Ø 175 Ø 200 Ø 250 Ø 300 10-80-018 - 10-100-018 50-100-018 2-125-018 30-125-018 2-150-018 30-150-018 10-175-018 50-175-018 10-200-018 50-200-018 60-250-018 - 60-300-018 - - - 17-125-018 17-150-018 - - - - - - 14-125-018 14-150-018 - - - - Adjustable Pipe 800-1300mm Two piece adjustable length with an adjustment range of 800mm to 1300mm.
STRAIGHT PIPES Adjustable Pipe 250-350mm Two piece adjustable length with an adjustment range of 250mm to 350mm. The Pipe come with a body soluble ceramic blanket that is cut down to achieve the desired effective length, secured with a locking band to fix the pipe in place. No screws required.
ELBOWS AND TEES 90° Bend 3 segment 90 degree bend, for offset details see table on page 40 m Ø 80 Ø 100 Ø 125 Ø 150 Ø 175 Ø 200 Ø 250 Ø 300 10-80-030 - 10-100-030 50-100-030 2-125-030 30-125-030 2-150-030 30-150-030 10-175-030 50-175-030 10-200-030 50-200-030 60-250-030 - 60-300-030 - - - 17-125-030 17-150-030 - - - - - - 14-125-030 14-150-030 - - - - 87° Bend 3 segment 87 degree bend, for offset details see table on page 40 m Ø 80 Ø 100 Ø 125 Ø 150 Ø 175 Ø 200 Ø 25
ELBOWS AND TEES 15° Bend 2 segment 15 degree bend, for offset details see table on page 40 m Ø 80 Ø 100 Ø 125 Ø 150 Ø 175 Ø 200 Ø 250 Ø 300 10-80-033 - 10-100-033 50-100-033 2-125-033 30-125-033 2-150-033 30-150-033 10-175-033 50-175-033 10-200-033 50-200-033 60-250-033 - 60-300-033 - - - 17-125-033 17-150-033 - - - - - - 14-125-033 14-150-033 - - - - 90° Bend Inspection 90 degree bend with a fully condensing P1 access plug (with seals), this allows full inspection on 90 de
ELBOWS AND TEES 90° Tee The 90° Tee is usually installed when you are connecting the flue to the rear outlet of an appliance.
ELBOWS AND TEES Tee Cap cw Drain Used to cap off the bottom or unused end of a 90/135 tee, this is usually fitted to the bottom of a base support to allow easy removal for sweeping and access, this part includes a 10mm threaded drain to allow the connection of a drain pipe to carry away excess condense from the flue system.
SUPPORTS Locking Band The Locking Band is used to secure two parts of the flue together. A Locking Band is required at every joint.
SUPPORTS Wall Band 210-420mm Wall support are to be used for lateral support only and should be use a minimum of every 3 meters. Only recommended fixings should be used to fit the wall support to the building surface. This wall band allows you to set a distance of 80mm (minimum) and 420mm (maximum) adjustment from the wall surface allowing a 340mm adjustment. This wall support has to be manually cut down to achieve the desired effective length.
SUPPORTS Console Plate Console Plates can be used as a load bearing support in conjunction with 3rd party fixings. See page 41 for loading data.
SUPPORTS Joist Support Joist supports are used to support the chimney as it is passing through floor joists. The joist support is used in conjunction with fire stop plates and is fixed on the upper floor section spanning the floor joist allowing even weight distribution.
FIRE STOPS Firestop Plate Non-Ventilated (Gas and Oil) A Firestop plate is used to allow the chimney to pass between floors, for example, when you need the chimney to go through the ceiling on the ground floor through to the first floor. The steel plate is designed to provide the appropriate distance between the flue and the adjacent flammable materials, according to both fire and building regulations. A plate must be used top and bottom of the floor penetration.
FLASHINGS MasterFLASH Residential Tile Slate / High Temp. Suitable for tiled roofs and is temperature resistance -74°C to 260°C Environmentally safe lead free aluminium base. The SILICONE rubber upstand has a 20 year life. The built in 20° pitch allows adaptability to almost any roof pitch including 45°. The pull tab design and easy smooth tear grooving is intended to eliminate cutting by knife and allow for a circular hole.
FLASHINGS Lead Flashing Roof Pitch 0° to 35° Code 4 Lead flashing suitable for tiled and slate roofs.
FINISHING PLATES Round Finishing Plate 45° (1 Piece) The Round Finishing Plate comes in one complete part and is used to tidy the area around the flue as it passes through a wall. This plate is attached to the wall where the flue is passing through at 45°. Use silicone and screws to secure against the wall.
FINISHING P LATES 2 Piece Round Fixed Finishing Plate 45° (75mm wide) The Round Finishing Plate comes in two parts and is used to tidy the area around the flue as it passes through a wall. This plate is attached to the wall where the flue is passing through at 45° and comprises of 2 plates at a fixed angle of 45°. Use silicone and screws to secure against the wall.
TERMINALS Rain Cap Standard rain protection terminal designed to minimise water ingress directly into the flue outlet.
TERMINALS H-Cowl The H-Cowl is a static Anti-Down draft terminal that has no moving parts and is perfect for high wind areas. The terminal offers extremely good protection from water ingress.
ACCESSORIES Damper Section Flue Damper helps to regulate draught within the chimney. The Flue Damper is encased in a Pipe Length. It is not essential unless you have problems controlling your stove.
ACCESSORIES Gasket Seal The Gasket Seal is required where the chimney is being used on a condensing appliance. m Ø 80 Ø 100 Ø 125 Ø 150 Ø 175 Ø 200 Ø 250 Ø 300 15-80-102 - 15-100-102 15-100-102 15-125-102 15-125-102 15-150-102 15-150-102 15-175-102 15-175-102 15-200-102 15-200-102 65-250-102 - 65-300-102 - - - - - - - - - - - - - - - - - Special LOCKING BAND TWPro to KC The TWPro to KC transitional locking band is used when connecting into existing KC.
ACCESSORIES Loft Mesh Kit complete 1m high The loft mesh kit is used to meet building regulations. Within the loft area the flue system must be boxed in or properly enclosed. This is in order to avoid combustible materials either being placed too close to or falling against the chimney. The system makes the installation very quick and safe, ensuring the required space around the flue.
OFFSET DATA Ø80/130 CODO 45° 30° 15° Ø150/200 Ø175/225 Ø200/250 Ø250/300 Ø300/350 X Y X Y X Y X Y X Y X Y X Y X Y - 96.
SUPPORT D ATA Vertical Load Supports Lateral Supports [In meters of pipe] Product Base Support Plate Adjustable Base Support 80-280mm Console Plate Joist Support Roof Support 38 | TWPro Øint Load above Load bellow 080 12 3 100 12 125 12 150 Product Øext [Meters] Distance 130 3 150 3 3 175 3 3 200 3 12 3 225 3 175 12 3 250 3 200 12 3 300 3 250 12 3 300 12 3 350 3 080 12 3 130 3 100 12 3 150 3 125 12 3 175 3 150 12 3 200 3 175 9 3 2
Mi-Flue s Ltd. Tay min Busine s s Park , Mi tcham Road, Blackp o ol, L ancashire , F Y4 4QN T: 01 25 3 6 0 0 06 0 • F : 01 25 3 6 0 0 06 1 s ale s@mi-f lue s .c om • www.mi-f lue s .