JP-SERIES OPERATION MANUAL COLD WATER DIRECT DRIVEN PRESSURE WASHER CAUTION RISK OF INJURY! READ MANUAL BEFORE OPERATING! This manual is an important part of the pressure washer and must remain with this unit! ® Job Copyright Pro JP-Series 2006, Mi-T-M Operator’s Corporation Manual © Form #37-0460-E/S-081706
table of contents introduction................................................................................................................. 3 important safety warningS................................................................................4-7 FIRE & VENTILATION PRECAUTIONS................................................................. 4 SPRAY PRECAUTIONS......................................................................................... 5 DETERGENT CLEANING PRECAUTIONS....................
INTRODUCTION Congratulations on the purchase of your new Job Pro® pressure washer! You can be assured your Job Pro pressure washer was constructed with the highest level of precision and accuracy. Each component has been rigorously tested by technicians to ensure the quality, endurance and performance of this unit. This operator’s manual was compiled for your benefit.
IMPORTANT SAFETY WARNINGS FIRE & VENTILATION PRECAUTIONS: 1. This unit was designed for outdoor use only. NEVER operate this unit in an enclosed area. ALWAYS make certain there is adequate air (oxygen) for combustion as well as ventilation to prevent the presence of poisonous carbon monoxide gases. Beware of poorly ventilated areas or exhaust fans which can cause inadequate combustion or engine overheating. 2.
IMPORTANT SAFETY WARNINGS spray precautions: danger risk of injection or severe cutting injury! keep clear of nozzle! do not direct discharge stream at persons or pets! only trained operators should use this product. when operating this unit, basic precautions should always be observed including the following: 1. KEEP AWAY FROM THE SPRAY: a. Because of the high pressure and velocity of the spray, fluids can penetrate the skin, causing serious injury. b. Never point the gun at yourself or anyone else.
important safety warnings detergent cleaning precautions: 1. DO NOT use solvents or highly corrosive detergents or acid type cleaners with this pressure washer. Use only Mi-T-M detergents. 2. KNOW YOUR DETERGENTS! Be prepared to tell a physician exactly what you are using in the event of an emergency. Read the Material Safety Data Sheet (MSDS) provided with your Mi-T-M Detergent and all detergent labels. Follow all appropriate instructions regarding preparation use, safety and transportation.
important safety warnings adjustment precautions: 1. NEVER alter or modify the equipment, be sure any accessory items and system components being used will withstand the pressure developed. Use ONLY genuine Mi-T-M parts for repair of your pressure washer. Failure to do so can cause hazardous operating conditions and will void warranty. 2. NEVER make adjustments to the machinery while it is connected to the engine without first removing the ignition cable from spark plug.
wp/jp features-041806-JJT FEATURES FEATURES LISTING 1. Detergent Hose (Option) 2. Detergent Strainer (Option) 3. Water Inlet 4. Water Inlet Strainer 5. Water Outlet 6. Thermal Relief Valve 7. Engine 8. Decal- Warning: Risk of Burns 9. Decal- Caution: Risk of Fire 10. 11. 12. 13. 14. 15. 16. 17.
SAFETY DECALS & PLACEMENT FOR JP-SERIES. !!!do not remove safety decals from unit unless replacing with most current safety decal!!! REFER TO PAGE 8 FOR PLACEMENT Decal: Caution-Engine Fuel (Part #34-0599) CAUTION/PRECAUCION RISK OF FIRE Do not add fuel when product is operating. Allow engine to cool for two (2) minutes before refueling. RIESGO DE FUEGE No ponga combustible cuando el producto este en operacion. Permita que el motor se enfrie por 2 minutos antes de reablastecer de combustible.
INSTALLATION & PREPARATION attire: Proper attire is essential to your safety. It is advised to utilize whatever means necessary to protect eyes, ears, and skin. Additional safety attire (such as respiratory mask) may be required when using detergent cleaning agents with this washer. danger RISK OF EXPLOSION OR FIRE! DO NOT PLACE UNIT IN AN AREA WHERE FLAMMABLE GAS VAPORS MAY BE PRESENT.
INSTALLATION & PREPARATION warning NOZZLE REVIEW: Various nozzles may be quick-connected into the end of the wand to change the spray pattern or use the detergent feature. When using Quick Connects (Q.C.), be certain the connection is securely locked. If not, the high pressure water may shoot the nozzle from the wand, causing severe injury or serious damage. To determine spray fan, refer to the actual number stamped on the nozzle. The first two digits indicate the spray fan in degrees, i.e.
INSTALLATION & PREPARATION CHECK wATER INLET STRAINER water supply: 1. Select a water supply hose which is a quality grade of garden hose measuring at least 3/4” ID and no longer than 50 feet. 2. Check the water inlet strainer to ensure it is clean and free of any obstructions. Periodic cleaning of the water strainer will help prevent pump problems. As a strainer becomes obstructed, it restricts proper flow of water to the pump.
INSTALLATION & PREPARATION pre-start inspection procedures: Before starting the unit, perform the following procedures: 1. Check the oil level in the pump and engine. 2. Inspect the water inlet strainer. Clean or replace if necessary. See “Water Supply”, #2, pg. 12. 3. Check all hose connections to ensure they are securely tightened. See “Water Supply”, #3, pg. 12. 4. Inspect for system fuel leaks. If a fuel leak is found, DO NOT START UNIT! See “Fire & Ventilation Precautions”, #2 and #4, pg. 4.
operating instructions priming the pump: 1. It is essential to prime the pump on initial start-up and each time the water supply is disconnected from the unit after initial use. 2. Lay the high pressure discharge hose out to remove any loops. Water flow will constrict the hose, creating tight loops if the hose is not straight. NOTE: The nozzle assembly should NOT be connected to the gun assembly at this time. See “Nozzle Connection” pg. 11. 3.
operating instructions CLEANING WITH DETERGENTS (OPTION AW-8400-0021): 1. Refer to “Detergent Cleaning Precautions” pg. 6 before working with detergents. Be certain to wear protective safety attire as stated on pg. 10. 2. Prepare detergent solution according to label directions. Never pump acids, alkaline, abrasive fluids or solvents through the unit. 3. Some units are equipped with adjustable detergent knobs. Locate the clear vinyl hose which leads to the pump head. a.
storage & maintenance specific maintenance: ENGINE: The engine instructions that accompany your unit detail specific procedures for maintenance of the engine. Following the engine manufacturer’s recommendations will extend engine work life. PUMP: The pump oil must be changed after the first 25 hours of operation. Once the initial oil change hasbeen completed, it is recommended the oil be changed every 3 months or 250 hour intervals.
storage & maintenance winterizing: For storage and transportation purposes in subfreezing ambient temperatures it will be necessary to winterize this unit. This unit must be protected to the lowest incurred temperature for the following reasons: 1. If any part of the pumping system becomes frozen; excessive pressure may build up in the unit which could cause the unit to burst resulting in possible serious injury to the operator or bystanders. 2.
TROUBLESHOOTING SYMPTOM PROBABLE CAUSE REMEDY Engine will not start. Various engine problems. Refer to the Engine Manual accompanying your unit. Unit components are frozen. Allow to thaw. If any part of the unit becomes frozen; excessive pressure may build up in the unit which could cause the unit to burst resulting in possible serious injury to the operator or bystanders.
Accessories 15-0006 50-0136 50-0143 851-0007 851-0006 AW-3000-0000 AW-3020-0000 AW-4085-0016 AW-7003-1500 AW-7015-1200 AW-7015-1800 AW-7015-2400 AW-7103-1800 AW-7103-3600 AW-7103-7200 AW-7300-0003 AW-7300-0035 AW-7300-0004 AW-7300-0045 AW-7300-0005 AW-8400-0021 Supply Hose ¾ in. Hose Reel 13 in. (Holds 100 ft. of Hose) Hose Reel Bracket (Mounts to Baseplate) 3000 PSI Extension Hose 50 ft. 4000 PSI Extension Hose 50 ft.
STATEMENT OF WARRANTY Mi-T-M® Corporation warrants all parts, (except those referred to below), of your new Job Pro® Series pressure washer to be free from defects in materials and workmanship during the following periods: For Lifetime against freezing and cracking: Pump Manifold For Seven (7) Years from the date of original purchase: High Pressure Pump For Two (2) Years from the date of original purchase: Cart Assembly Plumbing For One (1) Year from the date of original purchase: GFCI Sele
NOTES Job Pro JP-Series Operator’s Manual 21
TABLA DE MATERIAS INTRODUCCION........................................................................................................................................ 23 ADVERTENCIAS IMPORTANTES DE SEGURIDAD...........................................................................24-27 PRECAUCIONES CONTRA INCENDIO Y DE VENTILACION.............................................. 24 PRECAUCIONES PARA ROCIADO.......................................................................................
INTRODUCCION ¡Felicitaciones por la compra de su nueva lavadora a presión Job Pro®! Puede estar seguro que su lavadora a presión Job Pro® fue construida con el nivel más alto de precisión y exactitud. Cada componente ha sido probado rigurosamente por técnicos para asegurar la calidad, la resistencia y el rendimiento de esta unidad. Este manual del operador fue compilado para su beneficio.
ADVERTENCIAS IMPORTANTES DE SEGURIDAD PRECAUCIONES CONTRA INCENDIO Y DE VENTILACION: 1. Esta unidad fue diseñada para uso al aire libre solamente. NUNCA opere esta unidad en un área cerrada. SIEMPRE asegúrese que haya aire (oxígeno) adecuado para la combustión así también como ventilación adecuada para evitar la presencia de gases venenosos de monóxido de carbono. Esté alerta en áreas mal ventiladas o con ventiladores aspiradores que pueden causar una combustión inadecuada o sobrecalentamiento del motor.
ADVERTENCIAS IMPORTANTES DE SEGURIDAD PRECAUCIONES PARA ROCIADO: PELIGRO RIESGO DE INYECCION O DE LESION GRAVE DE CORTE MANTENGASE ALEJADO DE LA BOQUILLA! NO DIRIJA LA CORRIENTE DE DESCARGA A LAS PERSONAS NI A LOS ANIMALES DOMESTICOS! SOLO LOS OPERADORES ENTRENADOS DEBEN USAR ESTE EQUIPO. DEBEN OBSERVARSE SIEMPRE LAS PRECAUCIONES BASICAS, INCLUYENDO LAS SIGUIENTES: 1. MANTENGASE ALEJADO DEL ROCIADO a.
ADVERTENCIAS IMPORTANTES DE SEGURIDAD PRECAUCIONES PARA LIMPIEZA CON DETERGENTES: 1. NO use solventes ni detergentes altamente corrosivos, ni limpiadores de tipo ácido con esta lavadora a presión. Use detergentes Mi-T-M solamente. 2. ¡CONOZCA SUS DETERGENTES! En el caso de una emergencia, esté preparado a informar al médico exactamente lo que usted está usando. Lea La Hoja de Datos de Seguridad del Material (MSDS) provista con su detergente Mi-T-M y todas las etiquetas de los detergentes.
ADVERTENCIAS IMPORTANTES DE SEGURIDAD PRECAUCIONES DE AJUSTE: 1. NUNCA altere ni modifique el equipo, asegúrese que todos los artículos accesorios y los componentes del sistema que se usan resistirán la presión desarrollada. Use SOLO piezas genuinas Mi-T-M para reparar su lavadora a presión. El no hacerlo puede causar condiciones operativas riesgosas y cancelará la garantía. 2. NUNCA efectúe ajustes a la máquina mientras esté conectada al motor, sin sacar primero el cable de encendido de la bujía.
wp/jp features-041806-JJT ELEMENTOS Y COMPONENTES LISTA DE LOS ELEMONTOS Y COMPONENTES 1. 2. 3. 4. 5. 6. 7. 8. 9. 28 Manguera de detergente (Opción) Tamiz de detergente (Opción) Entrada de agua Tamiz de entrada de agua Salida de agua Válvula de descarga térmica Motor Calcomanía-Silenciador caliente Calcomanía-Combustible del motor 10. 11. 12. 13. 14. 15. 16. 17.
calcomanias DE SEGURIDAD no retire las calcomanias de seguridad de la unidad a menos que las reemplace por las calcomanias de seguridad mas recientes! Calcomanía-Combustible del motor (Pieza No. 34-0599) CAUtION/PRECAUCION RISK OF FIRE Do not add fuel when product is operating. Allow engine to cool for two (2) minutes before refueling. RIESGO DE FUEGE No ponga combustible cuando el producto este en operacion. Permita que el motor se enfrie por 2 minutos antes de reablastecer de combustible.
INSTALACION Y PREPARACION VESTIMENTA: Una vestimenta apropiada es esencial para su seguridad. Se recomienda que utilice cualquier medio necesario para proteger los ojos, los oídos y la piel. Al usar agentes limpiadores detergentes con esta lavadora, puede requerirse una vestimenta adicional de seguridad (tal como una máscara respiratoria). PELIGRO RIESGO DE EXPLOSION O INCENDIO! NO COLOQUE LA UNIDAD EN UN AREA DONDE PUEDAN ESTAR PRESENTES VAPORES INFLAMABLES.
INSTALACION Y PREPARACION BOQUILLA DE CONEXION RAPIDA: Pueden conectarse rápidamente varias boquillas al extremo de la vara para cambiar el patrón de rociado o para usar la característica de detergente. Asegúrese que la conexión está seguramente calzada, al usar los conectores rápidos (C.R.). En caso contrario el agua a alta presión puede despedir la boquilla de la vara, causando lesiones graves o daños importantes.
INSTALACION Y PREPARACION INSPECCIONE EL TAMIZ DE ENTRADA DE AGUA PRECAUCION ¡RIESGO DE DAÑO A LA UNIDAD! NO AJUSTE EN EXCESO EL DESCARGADOR. LA ROTURA RESULTARA EN UNA PERDIDA INMEDIATA DE PRESION DE AGUA Y REPARACIONES COSTOSAS. SUMINISTRO DE AGUA: 1. Seleccione una manguera de suministro de agua que sea de calidad de manguera de jardín que mida 3/4" de DI por lo menos y que no sea más larga que 50 pies. 2. Inspeccione el tamiz de entrada de agua para asegurar que esté limpio y libre de obstrucciones.
INSTALACION Y PREPARACION PROCEDIMIENTOS DE INSPECCION ANTES DEL ARRANQUE: Efectúe los procedimientos siguientes antes de arrancar la unidad: 1. Inspeccione el nivel de aceite en la bomba y en el motor. 2. Inspeccione el tamiz de entrada de agua. Limpie o reemplace si fuera necesario. Vea “Suministro de agua”, #2, pág. 32. 3. Inspeccione todas las conexiones de las mangueras para asegurar que estén bien ajustadas. Vea “Suministro de agua”, #3, pág. 32. 4.
INSTRUCCIONES DE OPERACION CEBADO DE LA BOMBA: 1. Es esencial cebar la bomba en el arranque inicial y cada vez que se desconecta el suministro de agua de la unidad después del uso inicial. 2. Desplieque la manguera de alta presión para eliminar los dobleces. El flujo de agua endurecerá la manguera, creando bucles rígidos si la manguera no está recta. NOTA: El conjecto de la boquilla NO debería conectarse al conjunto de la pistola en este momento. Vea “Conexión de la boquilla”, pág. 31. 3.
INSTRUCCIONES DE OPERACION 8. ASEGURE la pistola a gatillo en la posición “OFF” siempre que cambie las boquillas de conexión rápida. ¡NUNCA mire directamente en la boquilla! ¡El agua a alta presión crea un riesgo de lesiones graves! 9. No permita que la unidad funcione en un modo de derivación (con el gatillo cerrado) por más de tres minutos sin accionar el gatillo de la pistola.
INSTRUCCIONES DE OPERACION APAGADO: 36 1. APAGUE el motor según se instruye en el Manual del Motor. 2. CIERRE el suministro de agua. 3. Accione momentáneamente la pistola a gatillo para eliminar toda la presión interna, apuntando la pistola en una dirección segura. 4. Desconecte el conjunto de la boquilla, una vez que se haya eliminado la presión. 5. Desconecte y drene la pistola, la vara y las mangueras. 6.
ALMACENAMIENTO Y MANTENIMIENTO MANTENIMIENTO ESPECIFICO: MOTOR: Las instrucciones del motor que acompañan a su unidad detallan los procedimientos específicos para el mantenimiento del motor. El observar las recomendaciones del fabricante del motor prolongará la vida útil del motor. BOMBA: El aceite de la bomba debe ser cambiado después de las primeras 25 horas de operación en todas las unidades. Se recomienda intervalos de 250 horas, después de la carga inicial.
ALMACENAMIENTO Y MANTENIMIENTO ADVERTENCIA ¡RIESGO QUE LA UNIDAD REVIENTE! ¡NO ALMACENE/OPERE LA UNIDAD EN UN AMBIENTE HELADO! 32˚F 0˚C PREPARACION PARA EL INVIERNO: Será necesario preparar esta unidad para el invierno, para fines de Almacenamiento y transporte en temperaturas ambiente inferiores al punto de congelación. Esta unidad debe protegerse contra la temperatura más baja incurrida por las siguientes razones: 1.
ALMACENAMIENTO Y MANTENIMIENTO k. Apunte la vara hacia el recipiente vacío. l. Accione el gatillo de la pistola hasta que el anticongelante comience a salir por la vara. Suelte el gatillo por 3 segundos, a continuación accione el gatillo de la pistola por 3 segundos. Continúe ciclando la pistola varias veces hasta que toda la mezcla anticongelante es extraída del recipiente por la acción de sifón. m.
LOCALIZACION DE FALLAS SINTOMA CAUSA PROBABLE SOLUCION El motor no arranca. Varios problemas del motor. Refiérase al Manual del Motor que acompaña a su unidad. Los componentes de la unidad están congelados. Permita que se descongele. Si se congela cualquier parte de la unidad, puede acumularse una presión excesiva en la unidad, lo que podría causar que la misma reviente, resultando en lesiones posibles graves al operador o a los observadores.
LOCALIZACION DE FALLAS SINTOMA CAUSA PROBABLE SOLUCION El detergente no fluirá por sifón en el modo de detergente a baja presión. El tamiz del detergente no está completamente sumergido en la solución de detergente. Inspeccione, sumerja si fuera necesario. El tamiz del detergente está obstruido. Inspeccione, limpie o reemplace. La manguera del detergente está cortada, obstruida o doblada. Inspeccione, limpie o reemplace. La perilla de ajuste del detergente está girada a la posición cerrada.
Accessoires 15-0006 50-0136 50-0143 851-0007 851-0006 AW-3000-0000 AW-3020-0000 AW-4085-0016 AW-7003-1500 AW-7015-1200 AW-7015-1800 AW-7015-2400 AW-7103-1800 AW-7103-3600 AW-7103-7200 AW-7300-0003 AW-7300-0035 AW-7300-0004 AW-7300-0045 AW-7300-0005 AW-8400-0021 Manguera de alimentación de 3/4" Carrete para la manguera 100' Ménsula de la manguera Manguera de extensión de 50' de 3000 PSI Manguera de extensión de 50' de 4000 PSI Correador de arena-Punte de carburo Correador de arena-Punte de ceramic
DECLARACIÓN DE GARANTÍA Mi-T-M Corporation garantiza que todas las piezas (excepto aquellas a las que se hace referencia abajo), de su nueva lavadora a presión Job Pro® Series Cestán libres de defectos en materiales y mano de obra durante los periodos siguientes: ® Para un curso de la vida contra congelar y agrietarse: Colector de bomba Por siete (7) años a partir de la fecha original de compra: Bomba de Alta Presión Por dos (2) años a partir de la fecha original de compra: Carreta unidad
Manufactured by Mi-T-M 8650 Enterprise Drive, Peosta IA 52068 563-556-7484/ Fax 563-556-1235 44 Job Pro Serie-JP Manual del Operador