ADSL Modem with Built-In 802.
TABLE OF CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Key Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION Thank you for purchasing the ADSL Modem with Built-In 802.11g Wireless Router (the Router). In minutes, you will be able to share your Internet connection and network your computers. The following is a list of features that make your new Router an ideal solution for your home or small office network. OVERVIEW Key Features Integrated 802.11g Wireless Access Point 802.11g is an exciting new wireless technology that provides up to 54Mbps (nearly five times faster than 802.11b) data rates.
INTRODUCTION SPI Firewall Your Router is equipped with a firewall that will protect your network from a wide array of common hacker attacks including IP Spoofing, Land Attack, Ping of Death (PoD), Denial of Service (DoS), IP with zero length, Smurf Attack, TCP Null Scan, SYN flood, UDP flooding, Tear Drop Attack, ICMP defect, RIP defect, and fragment flooding.
INTRODUCTION Package Contents • ADSL Modem with Built-In 802.
KNOWING YOUR ROUTER Front Panel Power LED (PWR) ADSL – SYN Status LED ADSL – Data LED Wireless Network LED LAN Port Status LEDs Power LED (PWR) OFF Router is OFF Green Router is ready ADSL – SYN Status LED OFF No ADSL connection Solid Green ADSL connection is ready Blinking Green Negotiating connection This LED lights in GREEN to indicate that your Modem Router is connected properly to the ADSL line.
KNOWING YOUR ROUTER LAN Port-Status LEDs OFF No device is linked to the port Solid Orange 10/100Base-Tx device connected Blinking Orange Port activity These LEDs are labeled 1–4 and correspond to the numbered ports on the rear of the Router. When a computer is properly connected to one of the LAN ports on the rear of the Router, the LED will light. When information is being sent over the port, the LED blinks rapidly.
KNOWING YOUR ROUTER maintaining the programmed settings. You can also restore the factory default settings by using the Reset button. Use the restore option in instances where you may have forgotten your custom password. a. Resetting the Router Push and release the Reset button. When the Power/Ready light becomes solid again, the reset is complete. b. Restoring the Factory Defaults Press and hold the Reset button for 10 seconds then release it.
PLACEMENT OF YOUR ROUTER Proper placement of your Router is important to ensure the best performance of your wireless network. Typically, indoors your Wireless Router can provide a circular coverage area of 250 feet or more. However, different types of construction materials and other obstructions in a building can greatly affect the wireless signal and decrease the range. Whenever possible, your Router should be placed as close as possible to the center of the area that you want to cover.
CONNECTING AND CONFIGURING YOUR ROUTER ISP Settings Please collect the following information from your ISP before setting up the Wireless ADSL Modem Router.
CONNECTING AND CONFIGURING YOUR ROUTER Installing with a Splitter Installing a Splitterless Connection If you are using a splitterless (G.lite) connection, then your service provider will attach the outside ADSL line directly to your phone system. In this case, you can connect your phones and computer directly to the incoming ADSL line, but you will have to add low-pass filters to your phones as shown on the next page.
CONNECTING AND CONFIGURING YOUR ROUTER Installing without a Splitter Attach to your Network Using Ethernet Cabling The four LAN ports on the ADSL Modem Router auto-negotiate the connection speed to 10Mbps Ethernet or 100Mbps Fast Ethernet, as well as the transmission mode to half duplex or full duplex. Configuring the Router The Belkin Wireless ADSL Modem Router is equipped with a Web-Based Interface that you can use to set up the Router.
CONNECTING AND CONFIGURING YOUR ROUTER • Set the Router’s firewall to work with specific applications (port forwarding). • Set up security features such as client restrictions and MAC address filtering. • Enable the DMZ feature for a single computer on your network. • Change the Router’s internal password. • Reset the Router. • Reset the Router’s default settings. • Update the Router’s firmware. Step 1: Installing the Hardware 1. Power down your equipment. 2.
CONNECTING AND CONFIGURING YOUR ROUTER 6. Turn on the rest of your computers. After your computers boot up, a LAN link light (on the front of the Router) will be on for each port to which a wired computer is connected. These lights are your means to verify that your computers are connected. LAN Port Status LEDs Step 2: Set your Computer’s Network Settings to Work with a DHCP Server Configure the TCP/IP settings on your computers to obtain an IP address automatically.
CONNECTING AND CONFIGURING YOUR ROUTER Logging into the Router To configure the Router’s settings, you have to log in. The Router is supplied with no password entered. In the login screen, leave the password blank and click the “Submit” button to log in. Logging out of the Router One computer at a time can log into the Router for the purposes of making changes to the settings of the Router. Once a user has logged in to make changes, there are two ways that the computer can be logged out.
NAVIGATING THE WEB BROWSER INTERFACE Setup Wizard 1. Internet Sharing Select the connection type you are using. This information is provided by your ISP. 2. Setting your ISP Connection Type to PPPoE or PPPoA Enter the PPPoE (Point-to-Point Protocol over Ethernet) or PPPoA information in the provided spaces, and click “Next”. Click “Apply” to activate your settings. This information is provided by your ISP. User Name - Enter the ISP assigned user name. (Assigned by your ISP).
NAVIGATING THE WEB BROWSER INTERFACE 3. Setting your Connection Type to Disable Internet Sharing Enter VPI/VCI value in the provided spaces, and then click “Next”. Click “Apply” to activate your settings. VPI/VCI - Enter your Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI) parameter here. (Assigned by your ISP). 4. Setting your Connection Type to Multiple Protocol over ATM Mode Enter ATM (Asynchronous Transfer Mode) information in the provided spaces, and click “Next”.
NAVIGATING THE WEB BROWSER INTERFACE VPI/VCI - Enter your Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI) parameter here. (Assigned by your ISP). Default Gateway - Enter a default gateway IP address. If the Wireless ADSL Modem Router cannot find the destination address within its local network, it will forward the packets to the Default Gateway. (Assigned by your ISP). 5. Click apply to activate your settings. You have finished installing your new Belkin Router.
UNDERSTANDING THE WEB-BASED USER INTERFACE The home page shows you a quick view of the Router’s status and settings. All advanced setup pages can be reached from this page. 1 10 9 2 8 7 5 4 3 6 1. Quick-Navigation Links You can go directly to any of the Router’s UI pages by clicking directly on these links. The links are divided into logical categories and grouped by tabs to make finding a particular setting easier to find.
UNDERSTANDING THE WEB-BASED USER INTERFACE page where you will need to enter a password. When you are logged into the Router, you can make changes to the settings. When you are finished making changes, you can log out of the Router by clicking the “Logout” button. For more information about logging into the Router, see the section called “Logging into the Router”. 5. Help Button The “Help” button gives you access to the Router’s help pages.
UNDERSTANDING THE WEB-BASED USER INTERFACE Changing LAN Settings All settings for the internal LAN setup of the Router can be viewed and changed here. 1. LAN Settings Clicking on the header of the LAN tab (A) will take you to the LAN tab’s header page. A quick description of the functions can be found here. To view the settings or make changes to any of the LAN settings, click on “LAN Settings” (B) or to view the list of connected computers, click on “DHCP client list” (C).
UNDERSTANDING THE WEB-BASED USER INTERFACE 1. IP Address The “IP address” is the internal IP address of the Router. The default IP address is “192.168.2.1”. To access the setup interface, type this IP address into the address bar of your browser. This address can be changed if needed. To change the IP address, type in the new IP address and click “Apply Changes”. The IP address you choose should be a non-routable IP. Examples of a non-routable IP are: 192.168.x.x (where x is anything between 0 and 255) 10.
UNDERSTANDING THE WEB-BASED USER INTERFACE one day or one hour, frees IP addresses after the specified period of time. This also means that a particular computer’s IP address may change over time. If you have set any of the other advanced features of the Router, such as DMZ or client IP filters, these are dependent on the IP address. For this reason, you will not want the IP address to change. 6. Local Domain Name The default setting is “Belkin”.
UNDERSTANDING THE WEB-BASED USER INTERFACE 2. Internet WAN The “Internet WAN” tab is where you will set up your Router to connect to your Internet Service Provider. The Router is capable of connecting to virtually any ADSL Service Provider’s system provided you have correctly configured the Router’s settings for your ISP’s connection type. Your connection settings are provided to you by your ISP.
UNDERSTANDING THE WEB-BASED USER INTERFACE Connection Type From the Connection Type page, you can select the type of connection you use. Select the type of connection you use by clicking the radio button (1) next to your connection type and then clicking “Next” (2). 1 2 Setting your ISP Connection Type to PPPoE or PPPoA Enter the PPPoE (Point-to-Point Protocol over Ethernet) or PPPoA information in the provided spaces, and click “Next”. Click “Apply” to activate your settings.
UNDERSTANDING THE WEB-BASED USER INTERFACE a. Username - Enter the ISP assigned user name. (Assigned by your ISP). b. Password - Enter your password. (Assigned by your ISP). c. Retype Password - Confirm the password. (Assigned by your ISP). d. IP assigned by ISP - Select “Yes” for automatic IP assignment from your ISP. Select “No” only if your ISP assigns you a fixed IP address. e. IP address - If you are using a fixed IP address, enter the fixed IP address supplied by your ISP. f.
UNDERSTANDING THE WEB-BASED USER INTERFACE Setting your ISP Connection Type to Disable Internet Sharing VPI/VCI - Enter your Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI) parameter here. (Assigned by your ISP). Encapsulation - Select LLC or VC MUX. (Assigned by your ISP). Setting your ISP Connection Type to Multiple Protocol over ATM a b c d e a. WAN IP - Enter an IP address for the Wireless ADSL Modem Router WAN interface. (Assigned by your ISP). b.
UNDERSTANDING THE WEB-BASED USER INTERFACE DNS (Domain Name Server) Settings A “Domain Name Server” is a server located on the Internet that translates Universal Resource Links (URLs) like “www.belkin.com” to IP addresses. Many ISPs do not require you to enter this information into the Router. The “Automatic from ISP” box (1) should be checked if your ISP did not give you a specific DNS address.
UNDERSTANDING THE WEB-BASED USER INTERFACE requirements. Your Router is configured to operate on the proper channels for the country you reside in. The default channel is 11 (unless you are in a country that does not allow channel 11). The channel can be changed if needed. If there are other wireless networks operating in your area, your network should be set to operate on a channel that is different than the other wireless networks.
UNDERSTANDING THE WEB-BASED USER INTERFACE 1 2 Using the ESSID Broadcast Feature For security purposes, you can choose not to broadcast your network’s SSID. Doing so will keep your network name hidden from computers that are scanning for the presence of wireless networks. To turn off the broadcast of the SSID, select “DISABLE” and then click “Apply Changes”. The change is immediate. Each computer now needs to be set to connect to your specific SSID; an SSID of “ANY” will no longer be accepted.
UNDERSTANDING THE WEB-BASED USER INTERFACE • 11g Only Mode - 11g Only mode is compatible with 802.11g clients only. This mode can be useful only if you do not have any 802.11b clients that need access to the network. To switch modes, select the desired mode from the drop-down box next to “Wireless Mode” then click “Apply Changes”. • 11b Only Mode - It is not recommended you use this mode unless you have a very specific reason to do so.
UNDERSTANDING THE WEB-BASED USER INTERFACE There are two types of WPA security, WPA-PSK (no server) and WPA (with server). WPA-PSK uses what is known as a pre-shared key as the security key. A pre-shared key is basically a password that is between 8 and 40 characters long. It can be a combination of letters, numbers, or characters. Each client uses the same key to access the network. Typically, this is the mode that will be used in a home environment.
UNDERSTANDING THE WEB-BASED USER INTERFACE 1. From the Security Mode drop-down menu, select “WPA (with server)”. 2. Enter the IP address of the radius server into the “Radius Server” fields. 3. Enter the radius key into the Radius Key field. 4. Enter the key interval. Key interval is how often the keys are distributed (in packets). 5. Click “Apply Changes” to finish. You must now set all clients to match these settings.
UNDERSTANDING THE WEB-BASED USER INTERFACE 2. After selecting your WEP encryption mode, you can enter you WEP key manually by typing in the HEX WEP key manually, or you can type in a Passphrase in the Passphrase field and click “Generate” to create a WEP key from the passphrase. Click “Apply Changes” to finish. You must now set all of your clients to match these settings. 3. Encryption in the Router is now set.
UNDERSTANDING THE WEB-BASED USER INTERFACE Note to Mac users: Original Apple AirPort products support 64-bit encryption only. Apple AirPort 2 products can support 64-bit or 128-bit encryption. Please check your product to see which version you are using. If you cannot configure your network with 128-bit encryption, try 64-bit encryption. 4.
UNDERSTANDING THE WEB-BASED USER INTERFACE Application Gateways Settings Application gateways let you select ports to be open for certain applications to work properly with the Network Address Translation (NAT) feature of the Router. A list of popular applications has been included to choose from. Select your application from the drop-down list from the bottom of the screen. If your application is not here, you will need to check with the application vendor to determine which ports need to be configured.
UNDERSTANDING THE WEB-BASED USER INTERFACE Virtual Servers Virtual Servers allow you to route external (Internet) calls for services such as a web server (port 80), FTP server (Port 21), or other applications, through your Router to your internal network. Since your internal computers are protected by a firewall, machines from the Internet cannot get to them because they cannot be “seen”.
UNDERSTANDING THE WEB-BASED USER INTERFACE Access Control Access Control allows users to define the outgoing traffic permitted or denied access through the WAN interface. The default is to permit all outgoing traffic. To configure restrictive access to your computers, do the following: 1. Click “Add PC” on the Access Control screen. 2. Define the appropriate settings for client PC services (as shown on the following screen). 3. Click “OK” and then click “Apply Changes” to save your settings.
UNDERSTANDING THE WEB-BASED USER INTERFACE URL Blocking To configure the URL Blocking feature, specify the websites (www.anywebsite.com) and or keywords you want to filter on your network. Click “Apply Changes” to activate the change. To complete this configuration, you will need to create or modify an access rule in the “Client IP filters” section. To modify an existing rule, click the “Edit” option next to the rule you want to modify. To create a new rule, click on the “Add PC” option.
UNDERSTANDING THE WEB-BASED USER INTERFACE Follow these steps to add a schedule: 1. Click “Add Schedule Rule”. 2. You will see the following screen. 3. To configure the Schedule Rule, specify the Name, Comment, Start Time, and End Time that you want to filter on your network. 4. Click “OK” and then “Apply Changes” to save your settings. 5. To complete this configuration, you will need to create or modify an access rule in the Client IP filters section.
UNDERSTANDING THE WEB-BASED USER INTERFACE DMZ (Demilitarized Zone) If you have a client PC that cannot run an Internet application properly from behind the firewall, you can open the client up to unrestricted two-way Internet access. This may be necessary if the NAT feature is causing problems with an application such as a game or video conferencing application. Use this feature on a temporary basis. The computer in the DMZ is not protected from hacker attacks.
UNDERSTANDING THE WEB-BASED USER INTERFACE To put a computer in the DMZ, enter the last digits of its LAN IP address in the Static IP field and click “Apply Changes” for the change to take effect. If you are using multiple Public (WAN) IP addresses, it is possible to select which Public (WAN) IP address the DMZ host will be directed to. Type in the Public (WAN) IP address you wish the DMZ host to direct to, enter the last two digits of the IP address of the DMZ host computer, and click “Apply Changes”.
UNDERSTANDING THE WEB-BASED USER INTERFACE Restarting the Router to Restore Normal Operation 1. Click the “Restart Router” button. 2. The following message will appear. Click “OK” to restart your Router. Restore Factory Defaults Using this option will restore all of the settings in the Router to the factory (default) settings. It is recommended that you back up your settings before you restore all of the defaults. 1. Click the “Restore Defaults” button. 2. The following message will appear.
UNDERSTANDING THE WEB-BASED USER INTERFACE Saving/Backup Current Settings You can save your current configuration by using this feature. Saving your configuration will allow you to restore it later if your settings are lost or changed. It is recommended that you back up your current configuration before performing a firmware update. 1. Click “Save”. A window called “File Download” will open. Click “Save”. 2. A window will open that allows you to select the location in which to save the configuration file.
UNDERSTANDING THE WEB-BASED USER INTERFACE 3. When the save is complete, you will see the window below. Click “Close”. The configuration is now saved. Restore Previous Settings This option will allow you to restore a previously saved configuration. 1. Click “Browse”. A window will open that allows you to select the location of the configuration file. All configuration files end with a “.bin”. Locate the configuration file you want to restore and double-click on it. 2. Then, click “Restore”.
UNDERSTANDING THE WEB-BASED USER INTERFACE Firmware Update From time to time, Belkin may release new versions of the Router’s firmware. Firmware updates contain feature improvements and fixes to problems that may have existed. When Belkin releases new firmware, you can download the firmware from the Belkin update website and update your Router’s firmware to the latest version. Updating the Router’s Firmware 1. In the “Firmware Update” page, click “Browse”.
UNDERSTANDING THE WEB-BASED USER INTERFACE Setting or Changing the Administrator Password The Router ships with NO password entered. If you wish to add a password for greater security, you can set a password here. Write down your password and keep it in a safe place, as you will need it if you need to log into the Router in the future. It is also recommended that you set a password if you plan to use the remote management feature of your Router.
UNDERSTANDING THE WEB-BASED USER INTERFACE Enabling Remote Management Before you enable this advanced feature of your Belkin Router, MAKE SURE YOU HAVE SET THE ADMINISTRATOR PASSWORD. Remote management allows you to make changes to your Router’s settings from anywhere on the Internet. There are two methods of remotely managing the Router. The first is to allow access to the Router from anywhere on the Internet by selecting “Any IP address can remotely manage the Router”.
UNDERSTANDING THE WEB-BASED USER INTERFACE Enabling/Disabling UPnP UPnP (Universal Plug-and-Play) is yet another advanced feature offered by your Belkin Router. It is a technology that offers seamless operation of voice messaging, video messaging, games, and other applications that are UPnPcompliant. Some applications require the Router’s firewall to be configured in a specific way to operate properly. This usually requires opening TCP and UDP ports, and in some instances, setting trigger ports.
MANUALLY CONFIGURING NETWORK SETTINGS Set up the computer that is connected to the ADSL modem FIRST using these steps. You can also use these steps to add computers to your Router after the Router has been set up to connect to the Internet. Manually Configuring Network Settings in Mac OS up to 9.x 1. Pull down the Apple menu. Select “Control Panels” and select “TCP/IP”. 2. You will see the TCP/IP control panel. Select “Ethernet Built-In” or “Ethernet” in the “Connect via:” drop-down menu (1). 1 2 3.
MANUALLY CONFIGURING NETWORK SETTINGS 4. If not already set, at “Configure:”, choose “Using DHCP Server”. This will tell the computer to obtain an IP address from the Router. 5. Close the window. If you made any changes, the following window will appear. Click “Save”. Restart the computer. When the computer restarts, your network settings are now configured for use with the Router. Manually Configuring Network Settings in Mac OS X 1. Click on the “System Preferences” icon. 2.
MANUALLY CONFIGURING NETWORK SETTINGS 3. Select “Built-in Ethernet” (2) next to “Show” in the Network menu. 2 3 4 5 4. Select the “TCP/IP” tab (3). Next to “Configure” (4), you should see “Manually” or “Using DHCP”. If you do not, check the PPPoE tab (5) to make sure that “Connect using PPPoE” is NOT selected. If it is, you will need to configure your Router for a PPPoE connection type using your user name and password. 5.
MANUALLY CONFIGURING NETWORK SETTINGS Manually Configuring Network Settings in Windows 2000, NT, or XP 1. Click “Start”, “Settings”, then “Control Panel”. 2. Double-click on the “Network and dial-up connections” icon (Windows 2000) or the “Network” icon (Windows XP). 3. Right-click on the “Local Area Connection” associated with your network adapter and select “Properties” from the drop-down menu. 4.
MANUALLY CONFIGURING NETWORK SETTINGS Manually Configuring Network Settings in Windows 98 or Me 1. Right-click on “My Network Neighborhood” and select “Properties” from the drop-down menu. 2. Select “TCP/IP > Settings” for your installed network adapter. You will see the following window. 1 2 3 3. If “Specify and IP address” is selected, your Router will need to be set up for a static IP connection type. Write the address information in the table below.
MANUALLY CONFIGURING NETWORK SETTINGS Recommended Web Browser Settings In most cases, you will not need to make any changes to your web browser’s settings. If you are having trouble accessing the Internet or the Web-Based Advanced User Interface, then change your browser’s settings to the recommended settings in this section. Microsoft Internet Explorer 4.0 or Higher 1. Start your web browser. Select “Tools” then “Internet Options”. 2.
MANUALLY CONFIGURING NETWORK SETTINGS 4. Make sure there are no check marks next to any of the displayed options: “Automatically detect settings”, “Use automatic configuration script”, and “Use a proxy server”. Click “OK”. Then click “OK” again in the “Internet Options” page. Netscape Navigator 4.0 or Higher 1. Start Netscape. Click on “Edit” then “Preferences”. 2. In the “Preferences” window, click on “Advanced” then select “Proxies”. In the “Proxies” window, select “Direct connection to the Internet”.
GLOSSARY IP address The “IP address” is the Internal IP address of the Router. To access the advanced setup interface, type this IP address into the address bar of your browser. This address can be changed if needed. To change the IP address, type in the new IP address and click “Apply Changes”. The IP address you choose should be a non-routable IP. Examples of a non-routable IP are: 192.168.x.x (where x is anything between 0 and 255.) 10.x.x.x (where x is anything between 0 and 255.
GLOSSARY 3. You have to double-click on a desktop icon other than your browser to get on the Internet To set the Router to use PPPoE, type in your user name and password in the spaces provided. After you have typed in your information, click “Apply Changes”. After you apply the changes, the Internet Status indicator will read “connection OK” if your Router is set up properly. PPPoA (Routing Mode, for multiple PCs) Enter the PPPoA information in the provided spaces, and click “Next”.
GLOSSARY ESSID Broadcast Many wireless network adapters currently on the market possess a feature known as site survey. It scans the air for any available network and allows each computer to automatically select a network from the survey. This occurs if the computer’s SSID is set to "ANY”. Your Belkin Router can block this random search for a network.
GLOSSARY Virtual Servers This function will allow you to route external (Internet) calls for services such as a web server (port 80), FTP server (Port 21), or other applications through your Router to your internal network. Since your internal computers are protected by a firewall, machines from the Internet cannot get to them because they cannot be “seen”.
GLOSSARY MAC Address Filtering The MAC Address Filter is a powerful security feature that allows you to specify which computers are allowed on the network. Any computer attempting to access the network that is not specified in the filter list will be denied access. When you enable this feature, you must enter the MAC address of each client on your network to allow network access to each or copy the MAC address by selecting the name of the computer from the “DHCP Client List”.
GLOSSARY Assuming the time-out is set to 10 minutes, then 10 minutes after you leave, the login session will expire. You will have to login to the Router again to make any more changes. The login time-out option is for security purposes and the default is set to 10 minutes. Note, only one computer can be logged into the Router’s advanced setup interface at a time. Time and Time Zone The Router keeps time by connecting to a Simple Network Time Protocol (SNTP) server.
TROUBLESHOOTING You can find technical support information at www.belkin.com/networking or www.belkin.com through the tech support area. If you want to contact technical support by phone, please call 877-736-5771. Technical support is available 24-hours-a-day, 7-days-a-week. Problem Possible Cause/Solution The ADSL SYN LED is not on. 1. Check the connection between the Modem Router and ADSL line. Make sure the cable from the ADSL line is connected to the port on the Router labeled “ADSL”. 2.
TROUBLESHOOTING I’ve forgotten or lost my password. Press the Reset button on the rear panel (holding it down for at least five seconds) to restore the factory defaults. My wireless PC cannot connect to the Router. 1. Make sure the wireless PC has the same SSID settings as the Router, and you have the same security settings on the clients such as WPA or WEP encryption. 2. Make sure the distance between the Router and wireless PC are not too far away. The wireless network is often interrupted. 1.
INFORMATION FCC Statement DECLARATION OF CONFORMITY WITH FCC RULES FOR ELECTROMAGNETIC COMPATIBILITY We, Belkin Corporation, of 501 West Walnut Street, Compton, CA 90220, declare under our sole responsibility that the product, F5D7630-4 to which this declaration relates, complies with Part 15 of the FCC Rules.
INFORMATION Canada-Industry Canada (IC) The wireless radio of this device complies with RSS 139 & RSS 210 Industry Canada. This Class B digital complies with Canadian ICES-003. Cet appareil numérique de la classe B conforme á la norme NMB-003 du Canada. Europe-European Union Notice Radio products with the CE 0682 or CE alert marking comply with the R&TTE Directive (1995/5/EC) issued by the Commission of the European Community.
INFORMATION Belkin Corporation Limited Lifetime Product Warranty Belkin Corporation warrants this product against defects in materials and workmanship for its lifetime. If a defect is discovered, Belkin will, at its option, repair or replace the product at no charge provided it is returned during the warranty period, with transportation charges prepaid, to the authorized Belkin dealer from whom you purchased the product. Proof of purchase may be required.
belkin.com Belkin Corporation 5501 West Walnut Street Compton • CA • 90220-5221 • USA Tel: +1 310 898 1100 Fax: +1 310 898 1111 Belkin Components, Ltd. Express Business Park • Shipton Way Rushden • NN10 6GL • United Kingdom Tel: +44 (0) 1933 35 2000 Fax: +44 (0) 1933 31 2000 Belkin Components B.V. Starparc Building • Boeing Avenue 333 1119 PH Schiphol-Rijk • The Netherlands Tel: +31 (0) 20 654 7300 Fax: +31 (0) 20 654 7349 Belkin, Ltd.
