MCP4011/2/3/4 Low-Cost 64-Step Volatile Digital POT Package Types • Volatile Digital Potentiometer in SOT-23, SOIC, MSOP and DFN packages • 64 Taps: 63 Resistors with Taps to terminal A and terminal B • Simple Up/Down (U/D) Protocol • Power-on Recall of Default Wiper Setting - Custom POR wiper settings available (contact factory) • Resistance Values: 2.1 kΩ, 5 kΩ, 10 kΩ or 50 kΩ • Low Tempco: - Absolute (Rheostat): 50 ppm (0°C to 70°C typ.) - Ratiometric (Potentiometer): 10 ppm (typ.
MCP4011/2/3/4 1.0 ELECTRICAL CHARACTERISTICS † Notice: Stresses above those listed under “Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. Absolute Maximum Ratings † VDD ..................................................
MCP4011/2/3/4 AC/DC CHARACTERISTICS (CONTINUED) Electrical Specifications: Unless otherwise indicated, all parameters apply across the specified operating ranges. TA = -40°C to +125°C, 2.1 kΩ, 5 kΩ, 10 kΩ and 50 kΩ devices. Typical specifications represent values for VDD = 2.7V to 5.5V, VSS = 0V, TA = +25°C. Parameters Sym Resolution Min N Typ Max 64 Units Taps Conditions No Missing Codes Step Resistance RS — RAB / 63 — Ω Note 6 Wiper Resistance (Note 3, Note 4) RW — 70 125 Ω 5.
MCP4011/2/3/4 AC/DC CHARACTERISTICS (CONTINUED) Electrical Specifications: Unless otherwise indicated, all parameters apply across the specified operating ranges. TA = -40°C to +125°C, 2.1 kΩ, 5 kΩ, 10 kΩ and 50 kΩ devices. Typical specifications represent values for VDD = 2.7V to 5.5V, VSS = 0V, TA = +25°C.
MCP4011/2/3/4 AC/DC CHARACTERISTICS (CONTINUED) Electrical Specifications: Unless otherwise indicated, all parameters apply across the specified operating ranges. TA = -40°C to +125°C, 2.1 kΩ, 5 kΩ, 10 kΩ and 50 kΩ devices. Typical specifications represent values for VDD = 2.7V to 5.5V, VSS = 0V, TA = +25°C. Parameters Sym Min Typ Max Units VIH 0.7 VDD — — V Conditions Digital Inputs/Outputs (CS, U/D) Input High Voltage VIL — — 0.3 VDD V High-Voltage Input Entry Voltage VIHH 8.5 — 12.
MCP4011/2/3/4 tCSHI tCSLO CS tLUC 1/fUD tLO tLCUF tLUC tLCUF U/D tHI tLCUR tS tS W FIGURE 1-1: Increment Timing Waveform. SERIAL TIMING CHARACTERISTICS Electrical Specifications: Unless otherwise noted, all parameters apply across the specified operating ranges. Extended (E): VDD = +1.8V to 5.5V, TA = -40°C to +125°C. Parameters Sym Min Typ Max Units CS Low Time tCSLO 5 — — µs CS High Time tCSHI 500 — — ns 2.7V ≤ VDD ≤ 5.5V — — — ns 1.8V ≤ VDD < 2.7V 500 — — ns 2.
MCP4011/2/3/4 tCSHI tCSLO CS 1/fUD tLUC tLUC tHI tLCUF U/D tLO tLCUR tS tS W FIGURE 1-2: Decrement Timing Waveform. SERIAL TIMING CHARACTERISTICS Electrical Specifications: Unless otherwise noted, all parameters apply across the specified operating ranges. Extended (E): VDD = +1.8V to 5.5V, TA = -40°C to +125°C. Parameters Sym Min Typ Max Units CS Low Time tCSLO 5 — — µs CS High Time tCSHI 500 — — ns 2.7V ≤ VDD ≤ 5.5V — — — ns 1.8V ≤ VDD < 2.7V 500 — — ns 2.
MCP4011/2/3/4 tCSHI tCSLO 12V CS 5V tHUC 1/fUD tLO tHCUF tHUC tHCUF U/D tHI tHCUR tS tS W FIGURE 1-3: High-Voltage Increment Timing Waveform. SERIAL TIMING CHARACTERISTICS Electrical Specifications: Unless otherwise noted, all parameters apply across the specified operating ranges. Extended (E): VDD = +1.8V to 5.5V, TA = -40°C to +125°C. Parameters Sym Min Typ Max Units Conditions CS Low Time tCSLO 5 — — µs CS High Time tCSHI 500 — — ns 2.7V ≤ VDD ≤ 5.5V — — — ns 1.
MCP4011/2/3/4 tCSHI tCSLO CS 12V 5V 1/fUD tHUC tHUC tHI tHCUF U/D tLO tHCUR tS tS W FIGURE 1-4: High-Voltage Decrement Timing Waveform. SERIAL TIMING CHARACTERISTICS Electrical Specifications: Unless otherwise noted, all parameters apply across the specified operating ranges. Extended (E): VDD = +1.8V to 5.5V, TA = -40°C to +125°C. Parameters Sym Min Typ Max Units Conditions CS Low Time tCSLO 5 — — µs CS High Time tCSHI 500 — — ns 2.7V ≤ VDD ≤ 5.5V — — — ns 1.
MCP4011/2/3/4 TEMPERATURE CHARACTERISTICS Electrical Specifications: Unless otherwise indicated, VDD = +2.7V to +5.5V, VSS = GND.
MCP4011/2/3/4 2.0 TYPICAL PERFORMANCE CURVES Note: The graphs and tables provided following this note are a statistical summary based on a limited number of samples and are provided for informational purposes only. The performance characteristics listed herein are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified operating range (e.g., outside specified power supply range) and therefore outside the warranted range.
MCP4011/2/3/4 Note: Unless otherwise indicated, TA = +25°C, VDD = 5V, VSS = 0V. 120 0.05 100 0.025 80 0 DNL 60 -0.025 40 -0.05 20 0 8 25C Rw 25C INL 25C DNL 85C Rw 85C INL 85C DNL 125C Rw 125C INL 125C DNL 300 0.4 60 0.2 40 0 200 0 DNL RW 100 DNL RW 500 -0.
MCP4011/2/3/4 Note: Unless otherwise indicated, TA = +25°C, VDD = 5V, VSS = 0V. 2500 2000 2060 RWB (Ohms) Nominal Resistance (RAB) (Ohms) 2080 VDD = 5.5V 2040 2020 1500 1000 -40°C 25°C 85°C 125°C 500 VDD = 2.7V 0 2000 -40 0 40 80 Ambient Temperature (°C) 120 FIGURE 2-11: 2.1 kΩ – Nominal Resistance (Ω) vs. Ambient Temperature and VDD. © 2006 Microchip Technology Inc. 0 8 16 24 32 40 48 Wiper Setting (decimal) 56 64 FIGURE 2-12: 2.1 kΩ – RWB (Ω) vs.
MCP4011/2/3/4 Note: Unless otherwise indicated, TA = +25°C, VDD = 5V, VSS = 0V. WIPER WIPER WIPER U/D U/D U/D FIGURE 2-13: 2.1 kΩ – Low-Voltage Decrement Wiper Settling Time (VDD = 2.7V). FIGURE 2-16: 2.1 kΩ – Low-Voltage Increment Wiper Settling Time (VDD = 2.7V). WIPER WIPER U/D U/D FIGURE 2-14: 2.1 kΩ – Low-Voltage Decrement Wiper Settling Time (VDD = 5.5V). FIGURE 2-17: 2.1 kΩ – Low-Voltage Increment Wiper Settling Time (VDD = 5.5V). WIPER VDD FIGURE 2-15: Response Time.
MCP4011/2/3/4 Note: Unless otherwise indicated, TA = +25°C, VDD = 5V, VSS = 0V. 120 0.05 100 0.025 INL 80 0 DNL 60 -0.025 40 -0.05 20 0 -0.1 0 8 -40C Rw -40C INL -40C DNL 25C Rw 25C INL 25C DNL 85C Rw 85C INL 85C DNL 125C Rw 125C INL 125C DNL 350 0.075 300 0.025 250 0 DNL -0.025 150 -0.05 RW 100 50 0 16 24 32 40 48 -0.4 -0.
MCP4011/2/3/4 4950 6000 4925 5000 4900 4000 RWB (Ohms) Nominal Resistance (RAB) (Ohms) Note: Unless otherwise indicated, TA = +25°C, VDD = 5V, VSS = 0V. 4875 VDD = 5.5V 4850 4825 3000 2000 -40°C 25°C 85°C 125°C 1000 VDD = 2.7V 4800 0 -40 -20 0 20 40 60 80 100 120 Ambient Temperature (°C) FIGURE 2-24: 5 kΩ – Nominal Resistance (Ω) vs. Ambient Temperature and VDD. DS21978C-page 16 0 8 16 24 32 40 48 Wiper Setting (decimal) 56 64 FIGURE 2-25: 5 kΩ – RWB (Ω) vs.
MCP4011/2/3/4 Note: Unless otherwise indicated, TA = +25°C, VDD = 5V, VSS = 0V. WIPER WIPER U/D U/D FIGURE 2-26: 5 kΩ – Low-Voltage Decrement Wiper Settling Time (VDD = 2.7V). FIGURE 2-28: 5 kΩ – Low-Voltage Increment Wiper Settling Time (VDD = 2.7V). WIPER WIPER U/D FIGURE 2-27: 5 kΩ – Low-Voltage Decrement Wiper Settling Time (VDD = 5.5V). © 2006 Microchip Technology Inc. U/D FIGURE 2-29: 5 kΩ – Low-Voltage Increment Wiper Settling Time (VDD = 5.5V).
MCP4011/2/3/4 Note: Unless otherwise indicated, TA = +25°C, VDD = 5V, VSS = 0V. 0.05 120 0.025 100 DNL 80 0 INL 60 -0.025 40 -0.05 RW 20 -0.075 0 85C Rw 85C INL 85C DNL 125C Rw 125C INL 125C DNL DNL 300 INL 250 200 -0.05 150 -0.075 RW 100 -0.1 50 0 -0.125 8 60 0 40 -0.05 RW -0.1 -0.15 8 -40C Rw -40C INL -40C DNL 3000 25C Rw 25C INL 25C DNL 85C Rw 85C INL 85C DNL 125C Rw 125C INL 125C DNL 2500 DNL 2000 1500 INL 1000 500 RW 0 0 8 125C Rw 125C INL 125C DNL 1.
MCP4011/2/3/4 12000 10250 10230 10210 10190 10170 10150 10130 10110 10090 10070 10050 10000 VDD = 5.5V VDD = 2.7V RWB (Ohms) Nominal Resistance (RAB) (Ohms) Note: Unless otherwise indicated, TA = +25°C, VDD = 5V, VSS = 0V. 8000 6000 4000 -40°C 25°C 85°C 125°C 2000 0 -40 -20 0 20 40 60 80 100 120 Ambient Temperature (°C) FIGURE 2-36: 10 kΩ – Nominal Resistance (Ω) vs. Ambient Temperature and VDD. © 2006 Microchip Technology Inc.
MCP4011/2/3/4 Note: Unless otherwise indicated, TA = +25°C, VDD = 5V, VSS = 0V. WIPER WIPER U/D FIGURE 2-38: 10 kΩ – Low-Voltage Decrement Wiper Settling Time (VDD = 2.7V). WIPER U/D FIGURE 2-39: 10 kΩ – Low-Voltage Decrement Wiper Settling Time (VDD = 5.5V). DS21978C-page 20 U/D FIGURE 2-40: 10 kΩ – Low-Voltage Increment Wiper Settling Time (VDD = 2.7V). WIPER U/D FIGURE 2-41: 10 kΩ – Low-Voltage Increment Wiper Settling Time (VDD = 5.5V). © 2006 Microchip Technology Inc.
MCP4011/2/3/4 Note: Unless otherwise indicated, TA = +25°C, VDD = 5V, VSS = 0V. 120 0 INL -0.05 RW 40 150 -0.1 0 85C Rw 85C INL 85C DNL 125C Rw 125C INL 125C DNL 400 300 600 0.025 500 -0.025 INL 200 -0.05 100 -0.075 RW 0 8 85C Rw 85C INL 85C DNL 125C Rw 125C INL 125C DNL RW INL DNL 0 8 16 24 32 40 48 56 Wiper Setting (decimal) FIGURE 2-44: 50 kΩ Pot Mode – RW (Ω), INL (LSb), DNL (LSb) vs. Wiper Setting and Ambient Temperature (VDD = 1.8V). © 2006 Microchip Technology Inc.
MCP4011/2/3/4 Note: Unless otherwise indicated, TA = +25°C, VDD = 5V, VSS = 0V. 60000 49600 50000 49400 VDD = 5.5V 49200 49000 48800 VDD = 2.7V 48600 48400 RWB (Ohms) Nominal Resistance (RAB) (Ohms) 49800 40000 30000 20000 -40C 25C 85C 125C 10000 48200 48000 0 -40 -20 0 20 40 60 80 100 120 Ambient Temperature (°C) FIGURE 2-48: 50 kΩ – Nominal Resistance (Ω) vs. Ambient Temperature and VDD.
MCP4011/2/3/4 Note: Unless otherwise indicated, TA = +25°C, VDD = 5V, VSS = 0V. U/D U/D WIPER WIPER FIGURE 2-50: 50 kΩ – Low-Voltage Decrement Wiper Settling Time (VDD = 2.7V). FIGURE 2-53: 50 kΩ – Low-Voltage Increment Wiper Settling Time (VDD = 2.7V). U/D U/D WIPER WIPER FIGURE 2-51: 50 kΩ – Low-Voltage Decrement Wiper Settling Time (VDD = 5.5V). FIGURE 2-54: 50 kΩ - Low-Voltage Increment Wiper Settling Time (VDD = 5.5V). WIPER VDD FIGURE 2-52: Response Time.
MCP4011/2/3/4 Note: Unless otherwise indicated, TA = +25°C, VDD = 5V, VSS = 0V. -3dB Frequency (MHz) 4.5 4 A 2.1 k: 3.5 3 VIN 2.5 5 k: 2 1.5 10 k: 1 0.5 ~ Offset Gnd +5V W DUT + VOUT - B 50 k: 2.5V DC 0 -40 25 125 Temperature (°C) FIGURE 2-55: Temperature. DS21978C-page 24 -3 dB Bandwidth vs. FIGURE 2-56: Circuit. -3 dB Bandwidth Test © 2006 Microchip Technology Inc.
MCP4011/2/3/4 3.0 PIN DESCRIPTIONS The descriptions of the pins are listed in Table 3-1.
MCP4011/2/3/4 3.6 Chip Select (CS) The CS pin is the chip select input. Forcing the CS pin to VIL enables the serial commands. These commands can increment and decrement the wiper. Forcing the CS pin to VIHH enables the high-voltage serial commands. These commands can increment and decrement the wiper and are compatibe with the MCP402X devices. The wiper is saved to volatile memory (RAM). 3.
MCP4011/2/3/4 4.0 GENERAL OVERVIEW EQUATION 4-1: The MCP4011/2/3/4 devices are general purpose digital potentiometers intended to be used in applications where a programmable resistance with moderate bandwidth is desired.
MCP4011/2/3/4 4.2 Power-up 4.3 When the device powers up (rising VDD crosses the Trip Point Voltage (VTP)), the “default” wiper setting is restored. Table 4-1 shows the default value loaded into the wiper on POR/BOR. TABLE 4-1: DEFAULT POR WIPER SETTING SELECTION Default POR Wiper Setting Wiper Code Typical RAB Value -202 Mid-scale 1Fh 2.1 kΩ -502 Mid-scale 1Fh 5.0 kΩ -103 Mid-scale 1Fh 10.0 kΩ -503 Mid-scale 1Fh 50.
MCP4011/2/3/4 5.0 SERIAL INTERFACE 5.1 Overview 5.2 The MCP4011/2/3/4 utilizes a simple 2-wire interface to increment or decrement the digital potentiometer’s wiper terminal (W). This interface uses the CS and U/D pins. The CS pin is the Chip Select input, while the U/D pin is the Up/Down input. The Increment/Decrement protocol enables the device to move one step at a time through the range of possible resistance values. The wiper value is initialized with the “default” value upon power-up.
MCP4011/2/3/4 5.2.1 INCREMENT When the device voltage falls below the RAM retention voltage of the device, the wiper state may be corrupted. When the device returns to the operating range, the wiper will be loaded with the default POR wiper setting. This mode is achieved by initializing the U/D pin to a high state (VIH) prior to achieving a low state (VIL) on the CS pin. Subsequent rising edges of the U/D pin increment the wiper setting toward terminal A. This is shown in Figure 5-1.
MCP4011/2/3/4 5.2.2 Note: INCREMENT (FOR MCP402X COMPATIBILITY) When the device voltage falls below the RAM retention voltage of the device, the wiper state may be corrupted. When the device returns to the operating range, the wiper will be loaded with the Default POR wiper setting. This command allows compatibility with the MCP402X family, which supports updating of the non-volatile wiper setting. After the CS pin is driven to VIH (from VIL), any other serial command may immediately be entered.
MCP4011/2/3/4 5.2.3 DECREMENT When the device voltage falls below the RAM retention voltage of the device, the wiper state may be corrupted. When the device returns to the operating range, the wiper will be loaded with the default POR wiper setting. This mode is achieved by initializing the U/D pin to a low state (VIL) prior to achieving a low state (VIL) on the CS pin. Subsequent rising edges of the U/D pin will decrement the wiper setting toward terminal B. This is shown in Figure 5-3.
MCP4011/2/3/4 5.2.4 Note: DECREMENT (FOR MCP402X COMPATIBILITY) When the device voltage falls below the RAM retention voltage of the device, the wiper state may be corrupted. When the device returns to the operating range, the wiper will be loaded with the default POR wiper setting. This command allows compatibility with the MCP402X family, which supports updating of the non-volatile wiper setting. After the CS pin is driven to VIH (from VIL), any other serial command may immediately be entered.
MCP4011/2/3/4 5.2.5 Note: HIGH-VOLTAGE INCREMENT 1 (FOR MCP402X COMPATIBILITY) After the CS pin is driven to VIH (from VIL), any other serial command may immediately be entered. Note: This command allows compatibility with the MCP402X family, which supports updating of the non-volatile wiper setting with the WiperLock Technology feature. The wiper value will not overflow. That is, once the wiper value equals 0x3F, subsequent increment commands are ignored.
MCP4011/2/3/4 5.2.6 Note: HIGH-VOLTAGE INCREMENT 2 (FOR MCP402X COMPATIBILITY) After the CS pin is driven to VIH (from VIL), any other serial command may immediately be entered. Note: This command allows compatibility with the MCP402X family, which supports updating of the non-volatile wiper setting with the WiperLock Technology feature. The wiper value will not overflow. That is, once the wiper value equals 0x3F, subsequent increment commands are ignored.
MCP4011/2/3/4 5.2.7 Note: HIGH-VOLTAGE DECREMENT 1 (FOR MCP402X COMPATIBILITY) After the CS pin is driven to VIH (from VIL), any other serial command may immediately be entered. Note: This command allows compatibility with the MCP402X family, which supports updating of the non-volatile wiper setting with the WiperLock Technology feature. The wiper value will not underflow. That is, once the wiper value equals 0x00, subsequent decrement commands are ignored.
MCP4011/2/3/4 5.2.8 Note: HIGH-VOLTAGE DECREMENT 2 (FOR MCP402X COMPATIBILITY) After the CS pin is driven to VIH (from VIL), any other serial command may immediately be entered. Note: This command allows compatibility with the MCP402X family, which supports updating of the non-volatile wiper setting with the WiperLock Technology feature. The wiper value will not underflow. That is, once the wiper value equals 0x00, subsequent decrement commands are ignored.
MCP4011/2/3/4 5.3 CS High Voltage The CS pin is High-Voltage (VIHH) tolerant, like the MCP402X. This allows the MCP401X to be used in MCP402X applications without needing to change other portions of the application circuit. 6.0 RESISTOR Digital potentiometer applications can be divided into two categories: Figure 6-1 shows a block diagram for the MCP401X resistors. A RW (1) RW (1) RW (1) N = 62 Typical Resistance (Ω) Total (RAB) Step (RS) MCP401X-203E 2100 33.33 MCP401X-503E 5000 79.
MCP4011/2/3/4 6.1 Resistor Configurations 6.1.1 6.1.2 RHEOSTAT CONFIGURATION When used as a rheostat, two of the three digital potentiometer’s terminals are used as a resistive element in the circuit. With terminal W (wiper) and either terminal A or terminal B, a variable resistor is created. The resistance will depend on the tap setting of the wiper and the wiper’s resistance. The resistance is controlled by changing the wiper setting. The unused terminal (B or A) should be left floating.
MCP4011/2/3/4 6.2 Wiper Resistance The slope of the resistance has a linear area (at the higher voltages) and a non-linear area (at the lower voltages), where resistance increases faster than the voltage drop (at low voltages). Wiper resistance is the series resistance of the wiper. This resistance is typically measured when the wiper is positioned at either zero-scale (00h) or full-scale (3Fh).
MCP4011/2/3/4 6.3 Operational Characteristics Understanding the operational characteristics of the device’s resistor components is important to the system design. 6.3.1 6.3.1.1 6.3.1.2 Differential Non-Linearity (DNL) DNL error is the measure of variations in code widths from the ideal code width. A DNL error of zero would imply that every code is exactly 1 LSb wide.
MCP4011/2/3/4 6.3.2 MONOTONIC OPERATION Monotonic operation means that the device’s resistance increases with every step change (from terminal A to terminal B or terminal B to terminal A). The wiper resistance is different at each tap location. When changing from one tap position to the next (either increasing or decreasing), the ΔRW is less than the ΔRS. When this change occurs, the device voltage and temperature are “the same” for the two tap positions.
MCP4011/2/3/4 7.0 DESIGN CONSIDERATIONS In the design of a system with the MCP401X devices, the following considerations should be taken into account: • The Power Supply • The Layout 7.1 Power Supply Considerations The typical application will require a bypass capacitor in order to filter high-frequency noise, which can be induced onto the power supply's traces. The bypass capacitor helps to minimize the effect of these noise sources on signal integrity.
MCP4011/2/3/4 8.0 APPLICATIONS EXAMPLES VDD Non-volatile digital potentiometers have a multitude of practical uses in modern electronic circuits. The most popular uses include precision calibration of set point thresholds, sensor trimming, LCD bias trimming, audio attenuation, adjustable power supplies, motor control overcurrent trip setting, adjustable gain amplifiers and offset trimming.
MCP4011/2/3/4 8.2 Operational Amplifier Applications VDD VIN Figure 8-3, Figure 8-4 and Figure 8-5 illustrate typical amplifier circuits that could replace fixed resistors with the MCP4011/2/3/4 to achieve digitally-adjustable analog solutions. R3 A VIN MCP4011 A R3 MCP4012 FIGURE 8-4: Trimming Offset and Gain in a Non-Inverting Amplifier.
MCP4011/2/3/4 8.3 Temperature Sensor Applications VDD Thermistors are resistors with very predictable variation with temperature. Thermistors are a popular sensor choice when a low-cost, temperature-sensing solution is desired. Unfortunately, thermistors have non-linear characteristics that are undesirable, typically requiring trimming in an application to achieve greater accuracy. There are several common solutions to trim and linearize thermistors.
MCP4011/2/3/4 9.0 DEVELOPMENT SUPPORT 9.1 Evaluation/Demonstration Boards Currently there are three boards that are available that can be used to evaluate the MCP401X family of devices. 1. The MCP402X Digital Potentiometer Evaluation Board kit (MCP402XEV) contains a simple demonstration board utilizing a PIC10F206, the MCP401X and a blank PCB, which can be populated with any desired MCP4011/2/3/4 device in a SOT-23-5, SOT-23-6 or 150 mil SOIC 8-pin package.
MCP4011/2/3/4 10.0 PACKAGING INFORMATION 10.
MCP4011/2/3/4 Package Marking Information 8-Lead DFN (2x3) (MCP4011) Example: ABE 534 256 XXX YWW NNN Part Number Code MCP4011T-202E/MC ABE MCP4011T-502E/MC ABF MCP4011T-103E/MC ABG MCP4011T-503E/MC ABH Note: Applies to 8-Lead DFN Example: 8-Lead MSOP (MCP4011) XXXXXX 401122 YWWNNN 534256 8-Lead SOIC (150 mil) (MCP4011) Example: XXXXXXXX XXXXYYWW NNN 401152E e3 0534 SN^^ 256 Part Numbers 8L-MSOP Legend: XX...
MCP4011/2/3/4 5-Lead Plastic Small Outline Transistor (OT) (SOT-23) Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging E E1 p B p1 n D 1 α c A φ L β A1 INCHES* Units Dimension Limits A2 MIN MILLIMETERS NOM MAX MIN NOM Pitch n p .038 0.95 Outside lead pitch (basic) p1 .075 1.90 Number of Pins Overall Height 5 MAX 5 A .035 .046 .057 0.90 1.18 1.45 Molded Package Thickness A2 .
MCP4011/2/3/4 6-Lead Plastic Small Outline Transistor (CH) (SOT-23) Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging E E1 B p1 n D 1 α c A φ β A1 L INCHES* Units Dimension Limits MIN Pitch .038 BSC Outside lead pitch p1 .075 BSC Overall Height MILLIMETERS NOM n p Number of Pins A2 MAX MIN NOM 6 MAX 6 0.95 BSC 1.90 BSC A .035 .046 .057 0.90 1.18 1.
MCP4011/2/3/4 8-Lead Plastic Dual-Flat No-Lead Package (MC) 2x3x0.9 mm Body (DFN) – Saw Singulated Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.
MCP4011/2/3/4 8-Lead Plastic Micro Small Outline Package (MS) (MSOP) Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging D N E E1 NOTE 1 1 2 e b A2 A ϕ c L1 A1 Number of Pins Pitch Overall Height Molded Package Standoff Overall Width Molded Package Overall Length Foot Length Footprint Foot Angle Lead Thickness Lead Width Units Dimension Limits N e A Thickness A2 A1 E Width E1 D L L1 ϕ c b MIN — 0.75 0.
MCP4011/2/3/4 8-Lead Plastic Small Outline (SN) – Narrow, 150 mil (SOIC) Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging E E1 p D 2 B n 1 h α 45° c A2 A φ β L Units Dimension Limits n p INCHES* NOM 8 .050 .061 .056 .007 .237 .154 .193 .015 .025 4 .009 .017 12 12 MAX MILLIMETERS NOM 8 1.27 1.35 1.55 1.32 1.42 0.10 0.18 5.79 6.02 3.71 3.91 4.80 4.90 0.25 0.38 0.48 0.62 0 4 0.20 0.23 0.33 0.
MCP4011/2/3/4 APPENDIX A: REVISION HISTORY Revision C (December 2006) • Added device designators in conditions column to associate units (MHz) in Bandwidth -3 dB parameter in AC/DC Characteristics table. • Added device designations in conditions column for R-INL and R-DNL specifications. Revision B (October 2006) • For the 10 kΩ device, the rheostat differential non-linearity specification at 2.7V was changed from ±0.5 LSb to ±1 LSb. • Figure 2-9 in Section 2.
MCP4011/2/3/4 NOTES: DS21978C-page 56 © 2006 Microchip Technology Inc.
MCP4011/2/3/4 PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office. PART NO.
MCP4011/2/3/4 NOTES: DS21978C-page 58 © 2006 Microchip Technology Inc.
Note the following details of the code protection feature on Microchip devices: • Microchip products meet the specification contained in their particular Microchip Data Sheet. • Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. • There are dishonest and possibly illegal methods used to breach the code protection feature.
WORLDWIDE SALES AND SERVICE AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://support.microchip.com Web Address: www.microchip.