User's Manual
Table Of Contents
- Intended Use
- Prior to Installation
- Installation
- Child Safety
- During Use
- Maintenance and Cleaning
- Servicing
- Disposing of the FROSTMED
- Handling of CO2
- CO2 Canister Transportation
- CO2Temperature
- CO2 Pressure
- CO2 Refilling Process
- CO2 Canister Storage and Transportation (empty/full)
- In the very rare case of a frostbite
- IC and FCC Compliance
- This device complies with Industry Canada license-exempt RSS standard(s). This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device...
- FCC/ISED RF exposure
- This equipment complies with FCC radiation exposure limits and Canada radiation RF exposure limits set forth in CFR 47 Sections 2.1091 and Industry Canada RSS-102 for an uncontrolled environment. This equipment should be installed and operated with a ...
- FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
- Digital class B notice
- NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential insta...
- • Reorient or relocate the receiving antenna.
- • Increase the separation between the equipment and receiver.
- • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- • Consult the dealer or an experienced radio/TV technician for help.
- FDA clearance
- FROSTMED devices (PRO G1, PRO G2, LITE G1, LITE G2, LITE CV G1 and LITE CV G2 models) are
- FDA-cleared as Class II device, 510(K) exempts.
- 1. Introduction
- 2. Starting FROSTMED PRO, LITE, LITE CV
- 3. Operating FROSTMED
- 4. Removing Empty CO2 Canisters
- 5. Alert Programming and Notification
- 6. Troubleshoot
- 7. Service and Spare Parts
- 8. Customer Service Department
- Informations importantes relatives à la sécurité
- Utilisation prévue
- Avant l’installation
- Installation
- Sécurité des enfants
- Pendant l’utilisation
- Entretien et nettoyage
- Réparations
- Élimination de FROSTMED
- Manipulation du CO2
- Transport des cartouches de CO2
- Température du CO2
- Pression du CO2
- Processus de remplissage des cartouches de CO2
- Stockage et transport des cartouches de CO2 (vides/pleines)
- Dans les très rares cas d’engelures
- Conformité
- Informations importantes relatives à la sécurité
- 1. Introduction
- 2. Commencer à utiliser FROSTMED PRO, LITE, LITE CV
- 3. Fonctionnement de FROSTMED
- 4. Retrait des cartouches de CO2 vides
- 5. Programmation et notification des alertes
- 6. Dépannage
- 7. Réparation et pièces de rechange
- 8. Service client
•
A Red Light indicates the system is powered ON and operating/cooling.
•
A slowly blinking Blue Light indicates that the Bluetooth connection is available.
•
A rapid blinking Blue light indicates the Bluetooth connection is established.
•
A Green Light indicates the control valve is turned on and CO
2
will be released
.
Figure 12: LED Indicators for the FROSTMED PRO.
3.3
Charging Level of the Rechargeable Battery pack
To determine the level of the charge of the rechargeable battery pack, push the button on the
battery pack.
When the rechargeable battery is activated a set of four green LEDs will appear. A 100% charge is
equivalent to 4 LED lights. The higher the number of LEDs present, the more the battery is charged
3.4
Recommendations
1. The device is NOT sterile and biological/medical materials MUST BE protected and
isolated from the internal cooler's environment.
2. Double check the exposure temperature after transportation:
• Control the logged temperatures using the suitable app or/and
• Use a temperature monitor strip as temperature control backup (examples: 3M™
MONITORMARK™ TIME TEMPERATURE INDICATOR 9860C 10°C/50°F 48 HOUR, or
Berlinger Mini-tag or equivalent).