User's Manual
Table Of Contents
- Intended Use
- Prior to Installation
- Installation
- Child Safety
- During Use
- Maintenance and Cleaning
- Servicing
- Disposing of the FROSTMED
- Handling of CO2
- CO2 Canister Transportation
- CO2Temperature
- CO2 Pressure
- CO2 Refilling Process
- CO2 Canister Storage and Transportation (empty/full)
- In the very rare case of a frostbite
- IC and FCC Compliance
- This device complies with Industry Canada license-exempt RSS standard(s). This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device...
- FCC/ISED RF exposure
- This equipment complies with FCC radiation exposure limits and Canada radiation RF exposure limits set forth in CFR 47 Sections 2.1091 and Industry Canada RSS-102 for an uncontrolled environment. This equipment should be installed and operated with a ...
- FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
- Digital class B notice
- NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential insta...
- • Reorient or relocate the receiving antenna.
- • Increase the separation between the equipment and receiver.
- • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- • Consult the dealer or an experienced radio/TV technician for help.
- FDA clearance
- FROSTMED devices (PRO G1, PRO G2, LITE G1, LITE G2, LITE CV G1 and LITE CV G2 models) are
- FDA-cleared as Class II device, 510(K) exempts.
- 1. Introduction
- 2. Starting FROSTMED PRO, LITE, LITE CV
- 3. Operating FROSTMED
- 4. Removing Empty CO2 Canisters
- 5. Alert Programming and Notification
- 6. Troubleshoot
- 7. Service and Spare Parts
- 8. Customer Service Department
- Informations importantes relatives à la sécurité
- Utilisation prévue
- Avant l’installation
- Installation
- Sécurité des enfants
- Pendant l’utilisation
- Entretien et nettoyage
- Réparations
- Élimination de FROSTMED
- Manipulation du CO2
- Transport des cartouches de CO2
- Température du CO2
- Pression du CO2
- Processus de remplissage des cartouches de CO2
- Stockage et transport des cartouches de CO2 (vides/pleines)
- Dans les très rares cas d’engelures
- Conformité
- Informations importantes relatives à la sécurité
- 1. Introduction
- 2. Commencer à utiliser FROSTMED PRO, LITE, LITE CV
- 3. Fonctionnement de FROSTMED
- 4. Retrait des cartouches de CO2 vides
- 5. Programmation et notification des alertes
- 6. Dépannage
- 7. Réparation et pièces de rechange
- 8. Service client
Avant l’installation
Vérifiez FROSTMED pour détecter les éventuels dommages liés au transport. Vous ne devez en
aucun cas installer un FROSTMED endommagé. En cas de dommages, veuillez contacter le point
de vente.
Installation
•
Vous devez prendre des précautions lorsque vous déplacez FROSTMED.
•
Il est dangereux de modifier les spécifications techniques ou d’altérer ce produit d’une
quelconque manière.
•
Toutes les cartouches doivent être bien fixées avant de mettre FROSTMED en marche.
•
FROSTMED doit être posé à plat sur le fond de la glacière et/ou du conteneur isotherme où il a
été placé.
Sécurité des enfants
Ne laissez pas les enfants utiliser l’application Bluetooth qui contrôle FROSTMED sans la
surveillance d’un adulte !
Pendant l’utilisation
•
Ne placez pas de GLACE dans la glacière lorsque vous utilisez FROSTMED.
•
Les conteneurs contenant des gaz ou des liquides inflammables peuvent fuir à basse
température. Ne stockez pas de récipients contenant des substances inflammables, comme p.
ex. des bombes aérosols, des cartouches de recharge d’extincteurs, etc. avec FROSTMED.
•
N’immergez jamais FROSTMED.
Entretien et nettoyage
•
Éteignez toujours FROSTMED avant de procéder au nettoyage.
•
Essuyez toutes les surfaces avec une solution antimicrobienne (alcool isopropylique) et un
coton-tige.
Réparations
•
Ce produit doit être réparé par un technicien agréé, et seules des pièces détachées d’origine
doivent être utilisées.