User's Manual
Table Of Contents
- Intended Use
- Prior to Installation
- Installation
- Child Safety
- During Use
- Maintenance and Cleaning
- Servicing
- Disposing of the FROSTMED
- Handling of CO2
- CO2 Canister Transportation
- CO2Temperature
- CO2 Pressure
- CO2 Refilling Process
- CO2 Canister Storage and Transportation (empty/full)
- In the very rare case of a frostbite
- IC and FCC Compliance
- This device complies with Industry Canada license-exempt RSS standard(s). This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device...
- FCC/ISED RF exposure
- This equipment complies with FCC radiation exposure limits and Canada radiation RF exposure limits set forth in CFR 47 Sections 2.1091 and Industry Canada RSS-102 for an uncontrolled environment. This equipment should be installed and operated with a ...
- FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
- Digital class B notice
- NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential insta...
- • Reorient or relocate the receiving antenna.
- • Increase the separation between the equipment and receiver.
- • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- • Consult the dealer or an experienced radio/TV technician for help.
- FDA clearance
- FROSTMED devices (PRO G1, PRO G2, LITE G1, LITE G2, LITE CV G1 and LITE CV G2 models) are
- FDA-cleared as Class II device, 510(K) exempts.
- 1. Introduction
- 2. Starting FROSTMED PRO, LITE, LITE CV
- 3. Operating FROSTMED
- 4. Removing Empty CO2 Canisters
- 5. Alert Programming and Notification
- 6. Troubleshoot
- 7. Service and Spare Parts
- 8. Customer Service Department
- Informations importantes relatives à la sécurité
- Utilisation prévue
- Avant l’installation
- Installation
- Sécurité des enfants
- Pendant l’utilisation
- Entretien et nettoyage
- Réparations
- Élimination de FROSTMED
- Manipulation du CO2
- Transport des cartouches de CO2
- Température du CO2
- Pression du CO2
- Processus de remplissage des cartouches de CO2
- Stockage et transport des cartouches de CO2 (vides/pleines)
- Dans les très rares cas d’engelures
- Conformité
- Informations importantes relatives à la sécurité
- 1. Introduction
- 2. Commencer à utiliser FROSTMED PRO, LITE, LITE CV
- 3. Fonctionnement de FROSTMED
- 4. Retrait des cartouches de CO2 vides
- 5. Programmation et notification des alertes
- 6. Dépannage
- 7. Réparation et pièces de rechange
- 8. Service client
que la sangle en plastique maintienne fermement les deux cartouches ensemble.
REMARQUE : De légères fuites de gaz peuvent se produire lors de la mise en place des
cartouches. C’est normal. Néanmoins, un sifflement continu sans l’électronique est le signe
d’un mauvais alignement ou d’une valve défectueuse. Consultez la section de dépannage si le
problème persiste.
2.2
Activation de l’électronique
Les instructions suivantes s’appliquent aux modèles FROSTMED PRO, LITE et LITE CV.
Pour activer l’électronique, appuyez sur le bouton « ON/OFF ». La valve s’ouvrira
automatiquement et commencera le processus de refroidissement. Vous entendrez un sifflement
lorsque le gaz sortira de FROSTMED. C’est normal.
2.3
Connexion avec un appareil mobile
Ce système de refroidissement est contrôlé par l’application FROSTMED. Pour pouvoir contrôler
la température et les autres fonctions de FROSTMED, l’utilisateur doit avoir téléchargé
l’application sur le périphérique Bluetooth utilisé (p. ex. smartphone, tablette, etc.). L’application
est disponible sur [*Google Play Store et Apple App Store*].
Pour connecter FROSTMED via Bluetooth, ouvrez l’application FROSTMED qui est représentée par
l’icône suivante :
FROSTMED
Dans l’écran principal, touchez les trois points verticaux dans le coin supérieur droit pour ouvrir
les options. Dans la liste déroulante, sélectionnez « Rechercher FROSTMED ».