User's Manual
Table Of Contents
- Intended Use
- Prior to Installation
- Installation
- Child Safety
- During Use
- Maintenance and Cleaning
- Servicing
- Disposing of the FROSTMED
- Handling of CO2
- CO2 Canister Transportation
- CO2Temperature
- CO2 Pressure
- CO2 Refilling Process
- CO2 Canister Storage and Transportation (empty/full)
- In the very rare case of a frostbite
- IC and FCC Compliance
- This device complies with Industry Canada license-exempt RSS standard(s). This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device...
- FCC/ISED RF exposure
- This equipment complies with FCC radiation exposure limits and Canada radiation RF exposure limits set forth in CFR 47 Sections 2.1091 and Industry Canada RSS-102 for an uncontrolled environment. This equipment should be installed and operated with a ...
- FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
- Digital class B notice
- NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential insta...
- • Reorient or relocate the receiving antenna.
- • Increase the separation between the equipment and receiver.
- • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- • Consult the dealer or an experienced radio/TV technician for help.
- FDA clearance
- FROSTMED devices (PRO G1, PRO G2, LITE G1, LITE G2, LITE CV G1 and LITE CV G2 models) are
- FDA-cleared as Class II device, 510(K) exempts.
- 1. Introduction
- 2. Starting FROSTMED PRO, LITE, LITE CV
- 3. Operating FROSTMED
- 4. Removing Empty CO2 Canisters
- 5. Alert Programming and Notification
- 6. Troubleshoot
- 7. Service and Spare Parts
- 8. Customer Service Department
- Informations importantes relatives à la sécurité
- Utilisation prévue
- Avant l’installation
- Installation
- Sécurité des enfants
- Pendant l’utilisation
- Entretien et nettoyage
- Réparations
- Élimination de FROSTMED
- Manipulation du CO2
- Transport des cartouches de CO2
- Température du CO2
- Pression du CO2
- Processus de remplissage des cartouches de CO2
- Stockage et transport des cartouches de CO2 (vides/pleines)
- Dans les très rares cas d’engelures
- Conformité
- Informations importantes relatives à la sécurité
- 1. Introduction
- 2. Commencer à utiliser FROSTMED PRO, LITE, LITE CV
- 3. Fonctionnement de FROSTMED
- 4. Retrait des cartouches de CO2 vides
- 5. Programmation et notification des alertes
- 6. Dépannage
- 7. Réparation et pièces de rechange
- 8. Service client
5.
Taille de la glacière.
6.
Température ambiante.
La Figure 13 montre la durée de refroidissement utile en fonction de différentes températures
externes pour FROSTMED LITE, avec une température réglée à + 6 °C et des globules rouges
factices comme charge utile (tests effectués par la Société canadienne du sang le 27
août 2019) :
Figure 13 : Durée de refroidissement utile en fonction de la température extérieure
Si FROSTMED ne fonctionne pas correctement, veuillez effectuer les vérifications nécessaires
suivantes avant de contacter votre représentant local du service client FROSTMED.
FROSTMED n’est pas alimenté en courant.
Vérifiez que la batterie rechargeable de FROSTMED est entièrement ou partiellement chargée.
La température dans la glacière est trop élevée
Assurez-vous que le thermostat est réglé sur le réglage de température adapté aux conditions
de température ambiante/extérieure de la glacière.
Excès de givre, accumulation de glace
Vérifiez le niveau de température ambiante/extérieure. Si la température ambiante/extérieure
est supérieure à la température de consigne de l’application, il est alors possible que de la glace
s’accumule. Assurez-vous que la température ambiante/extérieure n’est pas inférieure à 10
°F/- 12 °C.
Sons de fonctionnement normaux
La valve s’ouvre, un bref sifflement est audible pendant environ 5 secondes.
Ce son est considéré comme normal. Si le sifflement dure plus de 10 à 15 secondes, consultez